DS3100集控站系统3.0版本现场安装手册课件

DS3100集控站系统

V3.0

现场安装手册

国电南京自动化股份有限公司电网事业部地址:南京市江宁区西门子路8号

邮编:211100

电话:025-********

传真:025-********

E-MAIL:ds3100@https://www.360docs.net/doc/1a11999019.html,

目录

1系统配置 (3)

2硬件配置 (4)

2.1机柜设备及接口 (4)

2.2 设备间连线 (6)

3软件配置 (7)

3.1 SCADA配置 (7)

3.1.1 MOXA(2610)配置 (7)

3.1.2交换机的配置(cisco2950) (7)

3.2天融信防火墙配置 (16)

3.2.1物理连接 (16)

3.2.2防火墙配置 (17)

3.3转发 (24)

3.3.1通道设置 (24)

3.3.2遥测转发 (26)

3.3.3遥信转发 (26)

3.3.4遥控转发 (27)

3.4五防 (28)

3.4.1物理连接 (28)

3.4.2数据库配置 (28)

3.4.3程序运行 (29)

2.1机柜设备及接口

2.2 设备间连线

3软件配置

3.1 SCADA配置

3.1.1 MOXA(2610)配置

(1)修改MOXA的双网切换时间:telnet moxa的IP地址,进入管理界面后,修改如下选项:port-mode-将Async server Proprietary Protocol ……选中后回车,

修改Tcp alive check time选项:将值7(默认)修改为1

备注:不可以修改为0,默认最小值为1

(2)解决遥控不能下发问题:telnet moxa的IP地址,进入管理界面后,修改如下选项:port-mode-将cts/rts选项修改为none

3.1.2交换机的配置(cisco2950)

Cisco交换机默认有24秒的测试时间,即对刚接入的网口进行测试,以免形成回路。如果这个时间影响现场的程序测试的话,可以进行如下设置,去掉24秒测试。

用串口线将计算机与路由器连接,加电

开始—程序—附件—通信—超级终端—新建连接—名称(随便键入名称)--

新建连接—名称(随便键入名称)

连接到com1口——确定

配置com1口属性——确定

确定后进入超级终端屏幕,以下为屏幕出现的内容:(黑体字为需输入的内容) % Please answer 'yes' or 'no'.

Would you like to enter the initial configuration dialog? [yes/no]: no

00:00:53: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state t

o up

Press RETURN to get started!

00:01:22: %LINK-5-CHANGED: Interface Vlan1, changed state to administratively do

wn

00:01:23: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state t

o down

Switch>en

Switch#sh run

Building configuration...

Current configuration : 1071 bytes

!

version 12.1

no service pad

service timestamps debug uptime

service timestamps log uptime

no service password-encryption

!

hostname Switch

!

!

ip subnet-zero

!

!

spanning-tree mode pvst

no spanning-tree optimize bpdu transmission spanning-tree extend system-id

!

!

!

!

interface FastEthernet0/1

!

interface FastEthernet0/2

!

interface FastEthernet0/3

!

interface FastEthernet0/4

!

interface FastEthernet0/5

!

interface FastEthernet0/6

!

interface FastEthernet0/7

!

interface FastEthernet0/8

!

interface FastEthernet0/9

!

interface FastEthernet0/10

!

interface FastEthernet0/11

!

interface FastEthernet0/12

!

interface FastEthernet0/13

!

interface FastEthernet0/14

!

interface FastEthernet0/15

!

interface FastEthernet0/16

!

interface FastEthernet0/17

!

interface FastEthernet0/18

!

interface FastEthernet0/19

!

interface FastEthernet0/20

!

interface FastEthernet0/21

!

interface FastEthernet0/22

!

interface FastEthernet0/23

!

interface FastEthernet0/24

!

interface Vlan1

no ip address

no ip route-cache

shutdown

!

ip http server

!

line con 0

line vty 5 15

!

!

end

Switch#conf t

Enter configuration commands, one per line. End with CNTL/Z. Switch(config)#int range f0/1 -24

Switch(config-if-range)#spanning-tree portfast

%Warning: portfast should only be enabled on ports connected to a single host. Connecting hubs, concentrators, switches, bridges, etc... to this interface when portfast is enabled, can cause temporary bridging loops. Use with CAUTION

%Portfast will be configured in 24 interfaces due to the range command but will only have effect when the interfaces are in a non-trunking mode.

Switch(config-if-range)#zz

zz

^

% Invalid input detected at '^' marker.

zz

^

% Invalid input detected at '^' marker.

zz

^

% Invalid input detected at '^' marker.

zz

^

% Invalid input detected at '^' marker.

zz

^

% Invalid input detected at '^' marker.

zz

^

% Invalid input detected at '^' marker.

zz

^

% Invalid input detected at '^' marker.

zz

^

% Invalid input detected at '^' marker.

zz

^

% Invalid input detected at '^' marker.

zz

^

% Invalid input detected at '^' marker.

zz

^

% Invalid input detected at '^' marker.

zz

^

% Invalid input detected at '^' marker.

zz

^

% Invalid input detected at '^' marker.

zz

^

% Invalid input detected at '^' marker.

zz

^

% Invalid input detected at '^' marker.

zz

^

% Invalid input detected at '^' marker.

zz

^

% Invalid input detected at '^' marker.

zz

^

% Invalid input detected at '^' marker.

zz

^

% Invalid input detected at '^' marker.

zz

^

% Invalid input detected at '^' marker.

zz

^

% Invalid input detected at '^' marker.

zz

^

% Invalid input detected at '^' marker.

zz

^

% Invalid input detected at '^' marker.

^

% Invalid input detected at '^' marker.

Switch(config-if-range)#wr

wr

^

% Invalid input detected at '^' marker.

wr

^

% Invalid input detected at '^' marker.

wr

^

% Invalid input detected at '^' marker.

wr

^

% Invalid input detected at '^' marker.

wr

^

% Invalid input detected at '^' marker.

wr

^

% Invalid input detected at '^' marker.

wr

^

% Invalid input detected at '^' marker.

wr

^

% Invalid input detected at '^' marker.

wr

^

% Invalid input detected at '^' marker.

wr

^

% Invalid input detected at '^' marker.

wr

^

% Invalid input detected at '^' marker.

wr

^

% Invalid input detected at '^' marker.

wr

^

% Invalid input detected at '^' marker.

wr

^

% Invalid input detected at '^' marker.

wr

^

% Invalid input detected at '^' marker.

wr

^

% Invalid input detected at '^' marker.

wr

^

% Invalid input detected at '^' marker.

wr

^

% Invalid input detected at '^' marker.

wr

^

% Invalid input detected at '^' marker.

wr

^

% Invalid input detected at '^' marker.

wr

^

% Invalid input detected at '^' marker.

wr

^

% Invalid input detected at '^' marker.

wr

^

% Invalid input detected at '^' marker.

^

% Invalid input detected at '^' marker.

Switch(config-if-range)#exit

Switch(config)#exit

Switch#

断开超级终端即可

3.2天融信防火墙配置

数据网的数据经过路由器后到达天融信防火墙,防火墙负责把从公网传来的数据经过地址转换后发送到独立采集的C网和D网,然后前置系统就可以实现网络通道的数据采集。

3.2.1物理连接

用交叉线连接路由器和防火墙的eth0口,用普通网线将防火墙的eth1口连接到C网交换机,将eth2口连接到D网交换机。

3.2.2防火墙配置

准备工作

1 公网分配的两个IP:10.34.206.83

10.34.206.84

公网路由:10.34.206.94

2 前置机IP

前置1 :C网192.166.100.13 D网192.166.101.13

前置2 :C网192.166.100.14 D网192.166.101.14

3防火墙IP配置

192.166.100.100

192.166.101.100

4防火墙缺省配置

Eth0 192.168.1.254 255.255.255.0

默认出厂用户名为:superman,密码为:talent

配置防火墙

用普通线连接笔记本电脑到Eth0口,IP地址设到

192.168.1.0网段,在IE浏览器中输入Https://192.168.1.254即可连接到防火墙,输入默认用户名和密码。

下列图片以合肥螺丝岗现场为例,输入Https:

//192.168.101.100

1.配置物理接口

Eth0口配置时,先增加一条路由,保存,原来的不要删除,等所有配置工作结束后在删除原来的纪录。

2.配置静态路由,增加一条网关

第20 页共29 页

相关文档
最新文档