Cable Eraction Test at Splay Band f

Cable Eraction Test at Splay Band for Spatial Suspension Bridge

Heungbae Gil , MASCE, AND Youngjae Choi

Abstract:

The Youngjong Grand Bridge include a self-anchored suspension bridge with inclined cable planes.The bridge use splay band (cable collars) to flare the main cable at anchorage, which is located at the end of a stiffing truss. During the cable erection,some of the wires at the splay band were expected to experience lateral displacement and/or lift phenomena because of the large flare angles at the splay band .mockup cable erection test at the anchorage were carried out to find the degree of displacement of wires and to determine appropriate measures to deal with these problems ,through these problems . Through these tests ,method to arrange wires at the splay bands were devised and tried ,and select method was successfully used for actually bridge. DOI:10,1061/(ASCE)1084-0702(2002)7:5(300)

CE Database keywords: Bridges, suspension ; Korea; Cables

Introduction

The young jiong Grand bridge consists of a steel box girder span, a truss span ,and a suspension span(Gil and cho1998).The suspension span (550m) is a self-anchored suspension bridge with inclined main planes(Fig.1).Self-anchored suspension bridge have the main cable anchorage at the Stiffing truss ,and only a limited number of them have been built (ochsendorf and biillington 1999).Due to the spatial layout of the cable ,the main cable plane of the main span is vertical during the cable spinning .But the cable planes become inclined as the hanger ropes (suspender )are linked to the main cable .In the completed state, the cable planes of the main and side spans are inclined ,The main cable planes of the suspension have 14 strands ,each of which Is composed of 480 galvanized parallel wires with a diameter of 5.1mm .the air spinning method ,which can have more wires per strands than the parallel wire strand method ,is used to erect main cables.

The typical suspension bridge use splay saddles to splay the main cable near the anchorage .The strands diverging from the splay saddles are flared and anchored to strand shoes or sockets and transmit the cable forces to anchor block ,In general ,the splay saddle is placed above the strand shoes or socket and spreads the cable downward .To flare the main cable as shown in Fig2 ,the suspension span of the Grand Bridge has a splay band (cable collar )rather than a splay saddle .The splay band binds and then spreads the cable symmetrically in the vertical and horizontal plane .The splay band shown in Fig3 is installed with an angle of 16.314°,which correspond to the angle of the main cable centerline .To accommodate the flare ,vertical and horizontal spacers ,shown in Fig4 ,are placed between the strands at the exit side of the splay band ,the splay band composed of two parts ,the top and the bottom .during the cable spinning ,the bottom of the splay band is temporarily fixed to the stiffing truss and wires are erected on it.the bottom has rectangle grooves to house the strands. after completion of the cable erection ,the top and bottom of the splay band are fastened by bolts and then the bands are released from the stiffing truss and equilibrium in the air.

The unique features of the suspension span –the self-anchored and spatial cable layout –pose cable erection problems ,which are most prominent in the tower saddles and at the splay band .Mockup erection test were performed to deal with these problems ;The problems of and the results of the mockup tests at the tower saddle are dealt with in an other paper (gil and choi2002) .this paper presents the results of mockup tests at the splay band .A few alternative proposals were

suggested to deal with the erection problems, and the optimal alternative was selected and used for erection of the main cables of the Grand Bridge.

Problem statements

The anchorage zone refers to the zone from the splay bands to the semicircular strand shoes .as shown in Fig 5 ,the strands shoes are symmetrically distributed around the main cable centerline .since the main cable anchorage is located at the stiffing truss ,The distance between the splay band and the strand shoes is rather short (13.0m).Furthermore ,the horizontal flare angle of the cable ,16.65°,is larger than the vertical flare angle 8.76°.Some strand shoes –for example ,Nos,8,10,and 14-are located above and/or the left(right)of the centerline .The strands linked to these strands bend at the complete state and showed lift and/or lateral displacement phenomena during cable erection .A detailed description of the cable erection problem is given below :

Lateral displacement of wires

In a typical earth-anchored suspension bridge, the splay saddle is placed above the strand and the horizontal flare is rather small .Therefore ,the wires at splay saddle bend downward and there is little horizontal movement of the wires .In the Grand Bridge ,14 strands composing a main cable fan out from the splay band and linked to the respective strand shoes .for the strand that have horizontal flare angles ,the horizontal bending force of the wires at the splay band is higher than the vertical bending force .This cause lateral displacement (shift)and pilling up of wires on the side of the splay band channel ,as shown in Fig6.

WIRE LIFT

In the complete state ,the strands as shown in Fig2 ,are symmetrical flare out from the splay band in vertical as well as in horizontal plane . To accommodate the flare of the main cable ,the band at the entrances (pylon sides) is straight but has vertical curvatures at the exit (strand shoe side) .The five strand shoes of the upper row (Fig5) are placed above the main cable centerline ,and the strands linked to these shoes bend upward with the angle of 4.338°after leaving the splay band at the complete state.

During cable spinning ,the bottom of the splay band is temporarily attached to the stiffing truss and the wires are erected on it .strands linked to the upper strand shoes tend to move upward .Because of this phenomena (wire lift), shown in Fig7 ,the wire toward the main pylon can be laid on the base of the band channel ,but the wire toward the strand shoes do not contract the base of the sadldle and therefore remain unsupported .this requires restraining of the wires during erection.

Test setup and procedure

The arrangement of 14 strands at the splay band is shown in Fig 3. In the mockup test ,the wire arrangement of two strands ,Nos .4and 10 ,were tested . During cable spinning ,the wires of the strand NO4 are expected to be displaced laterally at the splay band ,and those of NO.10 are expected to show both lateral displacement and lift.

A mockup strand shoe and splay band channels are placed on the frames ,as shown in Fig8, and the mockup strand shoe was placed on the left ;it was designed to be fixed at different position to model different strand shoes to be tested. The center frame housed the full scale splay band channels ,which are made of cast iron. The interior width of the channel is 105mm .the main cable angles at the splay band and flare angles of the strands were kept the same as those of the real bridge ,and the wires were looped around the strand shoes and anchored plate placed on the right

frame using wedges. The wires were tensioned using a 343N countering weight ,which corresponded to the cable tension during cable spinning.

Each strand in the real bridge has 480 wires (20 wires per x24 layers ).In the mockup test, the fewer than 100 wires (20 wires per layerx5layers) were erected for each strand .the lateral displacement of wires at the splay band was investigated first,after which the lift was performed. Lateral displacement

The test was performed using strand NO14,which was linked to the strand shoe located to the left of the centerline (Fig5).Its wires were expected to be displaced laterally during cable spinning.The splay band channel that stimulated the groove of the splay band is shown in Fig 9.The channel has horizontal and vertical curvatures at the exit side to accommodate flaring of the strand in both planes . several schemes to arrange the wires were devised and tried .The modification to splay band channel were made during the tests ,if necessary.

PROPOSAL 1 Wire Former use

A “wire former” proved to be an effective tool for the arrangement of the wires at the pylon saddle of the Grand Bridge (Gil and Choi2001).The wire former ,which look like somewhat a comb, is a steel bar with inserted piano wires were inserted to house 20 wires ,which is equal to the number of the wires to each layer .During cable erection ,the cable wires were placed in the slots between piano wires.

Wires formers were placed at both ends of the splay band channel in this test the test results showed that the wire former enable the arrangement at both end of the channel .At the inside of the channel ,however ,the arrangement was disturbed and the wires shifted to one side of due to the horizontal curvature of the channel and the lateral bending of the wires .it was also found that realigning the shifted wires by hand was almost impossible due to the wire tension. PROPOSAL2 Change of Wires layout order

In air spinning method of cable erection,The wires are classified into “dead wire”and “live wire”,depending on the position of the wires.To minimize the number of wire crossings (tangling )at the anchor span (from the splay band to the strand shoes), the dead wires are laid from the sides .therefore the wires at the splay band are arranged in the live wire-dead wire –live wire pattern shown in Fig11(a).The number in Fig11 represent the erection order of the wires inside the channel.

As explainearlier, the wires moved to one side (The left side in Fig 11), which caused disarrangement of the erected wires . It was thought that these problems could be dealt with by changing the layout order of the wires . the wires were simply placed from left to right without distinction between dead wires or live wires. Thus, as shown in Fig11(b),two live wires were followed by two dead wires(the spinning wheel carried two wires at a time )rather than the live wire-dead wire –live wire patten.

However, it was observed that the wires still shifted and piled up at the left side of the channel .A special wire guide was devised to prevent wire piling and keep the wires at the desired position. This device is a 95mm long metal bar, which is fixed at a height corresponding to the diameter of one wire(5.1mm).With the help of this guide ,the arrangement of the first layer wire can be easily finished. However, it was found that the arrangement of the first layer was easily disturbed when the guide was removed to erected the second layer. Furthermore, lots of wires crossings (tangling)were observed at the anchorage zone due to the mixture of the dead and the live wires. PROPOSAL3.Tension reduction by Slacking Device

In addition to horizontal bending of the strand ,wire tension was observed to cause the wire disarrangement as it tried to straighten the wires . It was thought that the wires could be easily managed and arranged by hand if the wire tension at the splay band is low enough .to reduce the wire tension inside the splay band, a tension-reduction” slacking device” was devised, as shown in Fig12.

As a part of the slacking device, a special fastener that can hold one layer of 20wires was introduced. One fastener was fixed at the exit side (strand shoe side)of the channel and the other was placed at the entrance side(pylon side)and connected to a turnbuckle. After a layer was erected, wires at both ends of the channel were arranged and held by the fasteners. Wire tension inside the band could be reduced by adjusting the turnbuckle.

Test resuts showed that the tension of the wire inside the splay band could be reduced by decreasing the distance between the fastener .However, the length of wires inside the channel was not reduced and the wires simply started to sag.As a result, arranging the wires was almost impossible .Even f the wires of the first layer was properly arranged ,The arrangement was easily disturbed when the fastener were removed for the erection of the second layer.

PROPOSA.Shape-preserving Device

One of the erection problem observed so far was how to maintain the arrangement of the previously erected layer during erection of a new layer.In Proposal 4 tie wires ,heat treated steel bars(thickness :3mm;width 25mm)and clamps ,as shown in Fig13,were employed to arrange the wires and to maintain the arrangement of the erected layers during the erection of a new layer.When necessary ,the sidewalls of the mockup splay band channel were cut out to install the device.To anchor thje bars and the clamps ,threaded rods were also welded to the channel base and sidwall.

During cable spinning, the erected wires were temporarily bound in order by tie wires.In addition to tie wires ,two clamps (Clamp1),shown in Fig14,were also installed to keep the wires temporarily in position during spinning. When new wires were spun,these clamps,which rotated around the threaded anchor,were opened and the wires were placed .Once all the wires of the first layer were laid ,the tie wires were removed and the wires were arranged by hand and by wood hammers , while two additional clamps ,which were installed at the sidewall ,held down the first-layer wires.After the arrangement ,two steel bars placed at the opening of the side walls were anchored to the base of the splay band and clamp2 were removed.

The steel bars maintained the arrangement of the wires during erection of the second layer. The second layer was erected on the top of the steel bars.The wires were spun and arranged as in the first and kept under clamp2 .After that ,the steel bars placed between the first and the second layers were pulled out and resinstalled at the top of the second layer.this procedure was repeated and enabled the arrangement of the wires at the splay band.

The interior width of the channel is 105mm and is larger than the width of the wire layer (5.1mmx20=102mm).the odd-numbered layers were placed from the right side wall of the channel and the even numbered layers were placed from the left side of the wall so that the wires of the new layer were placed on the groove-formed between the wires of an erected layer as shown inFig15.It was observed that due to horizontal bending ,the wires of the even-numbered layers tended to slide to the left side and on the top of the wires rather than on the grooves.To prevent this,a 3mm thick filler was installed between the side wall and the left wall.

Test Results

After a few trials,Proposal4 turned out to be the most satisfactory system to facilitated the arrangement of the wire with the lateral displacement phenomena .After the arrangement of each layer ,The height was measured to compare the theoretical height.The comparison in Table 1shows that the difference between the actual and the theoretical height is reduced as more layers are accumulated ,and that the height of the left side is higher than that on the right side.

Another important factor in the test was the amount of time required to arrange the layers.It took about 15min 20sfor the spinning wheel to travel from one anchorage to the other .In order not to hold the spinning wheel ,the layers need to be arranged within the time.It was determined that the wires could be arranged within this time because the arrangement time in Table 1 range from 14min23s to 12min40s.

Lift test

The tests were performed using the NO10 strand ,which was expected to show the wires lift as well as the lateral displacement phenomena. The splay band channel that houses the NO10 strand is made of cast iron and is installed with the angle of 16.2414°,corresponding to the main cable angle.As shown in Fig16,the channel has vertical and horizontal curvatures at the exit side to accommodate the flaring angle of the main cable.It was also designed to have a 450mm long strand spacer on the floor ,which is used to separated the strands inside the splay band at the exit side .In the test ,the actual degree of the wire lift was first determined and then compared with the analytical values.After that ,the schemes to control the lift and to arrange the wires were devised.

Test Procedure and Results

The steel bars and the clamps ,which were originally devised to prevent lateral displacement of the wires in previous test,were attached to the channel. Both maintained the arrangement of erected wires by pressing the wires against the bottom of the band channel .If necessary ,the sidewalls of the splay band channel were cut out to accommodate the steel bars and the clamps.

As expected ,the wires were in partial contact with the channel floor at the exited side due to the lift and vertical curvature of the splay band.Even when the wires were pressed against the floor by the clamps and bars ,a gap was observed between the first layer and the bottom of the channel.as shown in Fig 7.This gap occurred near the end of the horizontal strand spacer.Because of the gap in combination with the upward bend force of the wires,the bands and clamps could not effectively press the wire against the bottom ,and thus the wires tangled and could not be arranged.

A wood filler inside the splay band channel were employed to help in the arrangement of the wires .The wood filler was placed at the end of the horizontal strand spacer to fill the roombetween the wires and the channel floor.It acted as a reaction floor that took the force from the bars ,which held down the erected wires .For the actual splay band the length of the horizontal spacer was extended up to 815mm.Steel bars and clamps 1,as shown in Fig18 were also installed to prevent the disarrangement of the wires at the exit side of splay band.The lower supported bar was placed at the height corresponding to the height of the first layer wires in the complete state .The wires were laid on top of this support bar ,and when the erection of a layer was finished ,the wires were kept between the upper and lower bar at the designed position.

The operation sequence of the bars and the clamps to control the lift was similar to that to control the lateral displacement .the wires were erected on the top of the steel bars ,and the clamp limited the displacement of the erected wires .When a layer was erected ,the metal bars were pulled out and reininstalled on top of the just erected wires .After that the clamps were released and the wires

were erected again ,and this produce was repeated.

To measure the effectiveness of the devised system,The height of the erected layers were compared with that of the theoretical value .The result is summarized in Table 2 shows the difference between the actual and theoretical height of the layers .beginning with the second layer and increasing with the number of the layers .The maximum difference was slightly less than 4mm when the 10th layer was erected.however, the difference did not increase rapidly as the number of layers increased .

The difference between the actual and theoretical height of the NO 10strand was somewhat bigger than that of the NO4 strand shown in Table1 because the No4 strand only experienced the lateral shift phenomena . while the No10 experienced both the lateral displacement and the lift phenomena.

As explained earlier ,the travel time of spinning wheel between the anchorage is 15min20s. the time required to arrange each layer of the 10th strand tend to decrease as layer were accumulated .the required arrangement time for the 10th layer was less than 13min so that the wire arrangement was not expected to slow down the spinning operation.

Conclusion

Cable erection problems are expected during the erection of the suspension bridge with inclined cable planes.Some of the wires at the splay band deviated from the desire positions and move vertically and horizontally .Mockup cable erection test using full-scale splay band channels and strand shoes were carried out before the actual cable spinning .thorough a series of tests ,several schemes to arrange the wires and the strand were devised and tried .A combination of steel bars and clamps was found to be the most effective system to control wire displacement .As a consequence of the test results ,details of the splay band such as the length of the spacers was adjusted,The system was successfully employed for erection of the main cables in the actual bridge.

References

Ghi ,H and Cho, c (1998) …yongjiongGrand Suspension Bridge,Korea”struct Eng.int (IABSE,Zurich,Switzerland),8(2),97-98

空间悬索桥斜吊杆安装索缆试验

摘要:永江大桥中包含一段有斜缆索的自锚式悬索桥。该桥采用锚固在刚架末端的斜索面支撑主缆。在主缆的架设过程中,人们预计斜面索会因为相对较大的张角产生侧向位移或提升现象。人们用相同比例的实物模型试验来测量缆索的位移值,以决定采取相应的措施来解决这一问题。通过这些试验安排架设斜面上绳索的方案被修正,在尝试。最后的方案在实桥中得到成功的应用。

DOI:10.1061/(ASCE)1084-0702(2002)7:5(300)

数据库,关键词:桥,悬索,朝鲜;索缆。

简介:永江大桥包含一跨钢箱梁,一跨刚桁架,一跨悬索桥。悬索桥跨度550m,采取斜索面自锚体系。(如图1)自锚式桥主缆锚固在刚桁架上,只有一小部分已经完工。由于缆索的空间布置形式。在纺丝架缆过程中,主跨的主缆保持竖直。但是在吊杆与主缆相连后缆索平面会发生倾斜。在成桥状态主跨,边跨的索面都是斜的。悬索桥主缆由14股钢绞线绞合而成。每股包含480根直径5.1mm的镀锌钢丝。为架设主缆人们采用了可以比平行索法架设更多股钢丝的空气离心技术。

悬索桥在锚固区附近通常采用索鞍来支撑主缆。各股索缆在索鞍处分散开来,延伸出去。

由锚固脚或锚槽锚固。同时把索力传到锚固块上。一般来说,索鞍布置在股脚上部以把各索向下分散开来。为了像图2那样把各索合理的分散开来,大桥的悬索跨与其说采用索鞍还不如说用了倾斜的索箍,与个索连在一起,在水平和竖直方向将缆索对称的分散开来。图3所示斜索箍以16.314°安装。以同主缆轴线张角相适应。为了安放放射钢线,水平和竖直的定位块布置在各股钢索之间,斜吊杆外侧.斜吊杆由两份构成:顶部和底部。在纺索过程中索面下部临时固结在刚架上,然后在其上架设钢丝。吊杆的下部有可嵌入钢丝的索槽。索缆架设完毕后斜吊杆上下部都用螺栓锚固,然后在其自身平衡下,放松刚架的临时固结。

悬索桥段的独特之处在于:自锚式体系和其索的空间布置形式,带来一系列的架设问题,在索塔,索鞍处更加突出。为了解决这些问题人们许多按实物尺寸的模型演示试验,试验和鞍塔处的试验结果,另有文章论述。本文只论述斜索面的试验结果。为了解决架设问题,人们提出了好多可替代的架设方案,选出最好的用于大桥住缆架设。

问题的提出:

锚固区是指从斜索面底到半圆形套管的整个区域。如图5所示,套管沿主篮轴线对称布置。由于主缆锚固在刚架上,斜索面到套管的距离相当的小,只有13米,而且主索的水平倾角16.650o大于竖向8.76o的倾角。一些套管,例如8,10,14号只好安装在主缆轴线的上侧或偏左偏右。连接套管的索在成桥状态下是弯曲的。而在架设过程中表现出提升和侧移现象。下面对架设过程中出现的问题进行了细致的描述。

钢丝的侧向位移:

在典型的地锚式悬索桥中,索鞍放置在套管之上水平-位移非常小在大桥中14股缆索(包含主缆)像扇子一样在斜索面上展开。与各自的套管相连。对于这些有水平张角的钢索,斜索面上索的水平弯曲力比竖向弯曲力还大。这就导致了斜索槽侧面钢丝卷起。如图6所示钢丝的提升现象:

在成桥状态下,如图2所示,各股钢索从斜索面处向外延伸,在竖直和水平两个面内都是对称的。为了与主缆延伸相适应,面的入口一侧(塔架一侧)是直的,而在出口一侧(套管一侧)是竖向弯曲的。上面一排的5个套管布置在主缆轴线的上方,与这些套管相连的索在斜索成型后以4.3811o上扬。

在缆索的纺线过程中斜索底部要与刚架临时固结,然后在其上架索,与套管相连的索有向上移动的趋势。由于索的抬升趋势,如图7所示,朝向索塔一侧的索可以布置在索槽根部。但是朝向套管一侧的索并不与索鞍底部接触。因此始终得不到支撑,这就要在架设过程中约束主缆。

试验安装与安装次序:

14根主缆的布置形式如图3所示,在这些实物比例的模拟试验中,人们对4,10号两根索进行了试验。在纺索过程中人们预计4号索钢绞线在斜索面上会出现侧向位移。10号索回同时发生侧向位移和提升现象。

如图8所示,在框架上设置等比例的套管和索槽。套管设置在左侧,人们设计从不同的方位安装,以演示不同的套管试验。同时用以铸铁制造的中心框架将索槽封闭起来。索槽内部宽度为105㎜。斜索面处主缆的倾角及各索的张角与成桥状态保持一致,钢绞线缠绕在套管上,锚固在用楔子在右侧框架上安装的锚固块上。人们用343n的反力张拉缆索,以同纺索施工中对索的张拉力相同。

实桥中每根主缆都有480根钢绞线(24层,每层20根),人们对每根索配的钢绞线只有100根,(5层,每层20根)。先对侧向位移试验然后再对抬升现象试验》本试验以4号索进行演示,该索与主缆轴线左侧的套管相连,如图5所示,人们估计在纺索过程中该索会发生侧向位移,以斜索面上的槽来模拟实桥中的索槽。如图9所示。在出口一侧,索槽水平竖直方向都有弯曲。以与两个面内索的弯曲相适应。人们对几种安装索

的方案进行修正,试验。如有必要,在试验过程中人们对索槽也要修改。

方案一:采用索缆成型器。

大家一致认为,索缆成型器是塔鞍处安装索缆的有效工具。它看起来像个梳子,是一根内部塞有琴弦一样钢绞线的钢杆。如图10所示,将21根高强钢丝嵌入20根钢绞线中,这样就与每层上线的数目相同。在缆索架设过程中,索布置在钢丝的接缝之间。本试验中钢索成型器在斜索面两侧都有布置。试验结果表明,成型器使人们有能力在槽两侧都安装。索槽内侧的水平弯曲和钢绞线的侧向弯曲却造成了,索槽内部的安装障碍,而且钢索偏向一侧。同时人们发现用手工对张拉过的索重新定位几乎是不可能的。

方案二:改变索的安装次序。

以空气绞线法架设缆索。索,以其位置被分为:固定索于活动索两种。为了减少索在锚固段的交叉数量,(从索箍到套管)固定索从槽中心开始安装,活动索从两边开始。因此斜索面上槽的安装以活动-固定-活动的模式,如图11(a)所示。图11所示的数字代表槽内索的架设顺序。

正如前面解释的那样,钢绞线偏向一侧,(如图11,偏向左侧),这就造成了架设主缆安装不到位。大家认为通过改变索缆的安装次序可以解决这一问题。各索简单的从左向右架固定索和活动索之间不留空隙。因此像图11b那样,两条活动索紧跟着固定索架设。(纺车每次可以纺两条索),而不是采用活动-固定-活动的安装模式。

但是人们仍然发现槽左侧缆索的偏移,抬升现象。工程师设计了一个特制的导索来阻止缆索的抬升,以保证各索始终在其设计位置。这个装置是一根95㎜长的铁杆,安装在一个与缆索直径5.1㎜相适应的高度。在导索的帮助下,第一层索可以很轻松的安装好。但随后工程师们又发现,在用导索安装第二层索时,第一层索却碍手碍脚。更糟糕的是由于固定和活动索的混合使用,人们发现许多索在锚固区交叉。

方案三:用松弛装置降低预应力索的预应力。

除了钢丝索平弯之外,人们发现钢索的预加应力会尽量使钢索保持水平,同样造成钢索布置的紊乱。工程师们认为当索的预加力足够小时人们可以轻易的用手工对其进行控制,安装。为降低索面的内部应力,人们设计了一个降低索力的松弛装置,如图12所示。

人们引入了一个每层可以容纳20根索的扣件,作为松弛装置的一部分。一个安置在出口(套管一侧),另一个安置在槽入口(塔架一侧)与紧线器相连。架设完一层后,槽两侧的索也架设好了。并由这个紧线器来支撑。这样就可以通过调整紧线器来调整降低索的预加应力。

试验结果显示,人们可以通过缩短紧线器间的距离来降低索力。但是索槽内部索的长度并没有减少,它们很自然的开始下催。结果是安装索草几乎是不可能的。尽管第一层索可以安装得很合适,为安装第二层索移动紧线器时,安装工作很容易受阻。

方案四:形状保持装置。

到目前为止,人们发现的架设问题的一个是,怎样在架设新一层索缆时保持以架设索缆不发生位置变化。在方案四中,人们采用如图13所示的,绑扎用铁丝,热处理的钢条(3㎜厚,25㎜宽),还有索夹来布置缆索,以保证随后架设过程中先前架设的不发生位置改变。有必要的话,人们可以切断斜缆索槽的侧壁来安放这些设备。为锚固钢杆和夹子人们把螺纹钢筋也焊到了槽底和侧壁上。

在纺缆过程中以架设的索被绑扎钢丝临时连成一列,该施工阶段不但用到了绑扎钢丝,还用到了索夹,来保持索始终在其设计位置(如图14所示)。新的缆索纺完后,夹子绕着螺纹锚具旋转,打开然后将个股钢丝放置进去。第一层索安装完毕后,人们便将绑扎钢丝移走,靠手工和木锤布置缆索。同时另添加两个装在侧壁的夹子来压紧第一层索(Ⅱ型索夹),安装完毕后,侧壁开口处的钢杆被锚固到斜索底部,同时将Ⅱ型夹子移走。

在假设第二层索的过程中人们用钢杆来维持个索的布置。第二层索被架设在钢杆上,钢束像第一层索一样被纺起来,然后固定在Ⅱ型索夹下面。架设完毕后两层间的钢杆被抽出来。重新安在第二层上,此工艺流程循环进行,直到架设完毕。

索槽内部通道宽105㎜比索层厚度(5.1㎜×20=102㎜)要大。奇数层的缆索从索槽的右侧壁开始安装。偶数层的索从左侧开始安装。因此,新一层的缆索被安放在以架设好的钢绞线之间形成的凹槽处。如图15所示。人们发现由于索的平弯,偶数层索倾向于滑向左侧,从而到了以架设好索的顶部而不是在凹槽之中。为了阻止这种现象发生,人们在索槽侧壁和左弯较多的索之间安了一块3㎜厚的垫板。

试验结果:

经过这一系列的试验,人们发现方案四是解决安装缆索过程中发生侧向位移的理想体系。安装完每一层后工程师都要测量其高度与理论高度值相比较。从表1的比较中我们可以发现随着层数的增加实际与理论高差越来越小,而且左侧发生偏移的一边反而比右册侧还高些。

试验的另一个重要因数是安装个索所需要的时间。人们用纺车把揽索从一个锚固区牵引到另一个锚固区所需要的时间大约是15分20秒。为了不影响纺线,各层必须在这段时间内完成。这一点人们还是很自信的,因为从表1得到的试验数据,时间为从14分23秒到12分40秒,小于纺丝所需要的时间。

抬升试验:

工程师取预计会发生抬升现象并伴随侧向位移的10号索作为试验对象。容纳10号索的索槽采用铸铁作成,安装是采用与主缆相适应16.2414°。如图16所示,为与主缆的张角相适应,10号索槽在水平和竖直面内都有弯曲。而且人们专门设计了一个架设在地面上450㎜的水平缆索定位架,人们用它在斜缆索内部将个条索分隔开来。在试验中人们先预计一个量值然后与分析后的实际数值想比较再设计控制抬升与布索方案。

试验程序与结论;

最初设计用来阻止先前试验缆索侧向位移的钢杆和夹子同索槽连在一起,两者都是通过将缆索压向索槽底部来保持以架设缆索的位置。如有必要可以切断斜索面槽的侧壁来安放钢杆,夹子。

正如预计的那样,由于斜索面的竖向弯曲和抬升,钢索只与底部部分相接触,如图7所示,尽管用钢杆,夹子可以向下压人们仍然发现第一层和与底版之间有一条很大的缝隙。在水平索缆定位器末端附近。由于缝隙的存在在加上索缆的纵向向上移动,钢杆甲子并不能将索缆有效的压回底部,这样钢索变得紊乱而无法安装。

人们吊杆内部引入了一个木制的垫板,索槽外侧布置一对钢杆来帮助钢索安装。如图17所示,木制的垫板被安装在水平索缆定位器末端来填充索缆与槽底的空间。它支撑着架设好的索缆,被工程师用做抵抗钢杆传来力的平面。在实吊杆中水平垫板被延伸到815㎜长。如图18所示,安装在吊杆外侧的钢杆,索夹同样阻止索缆变得紊乱。在成桥状态下,低一些支架的架设高度要与第一层索缆的布置高度相适应,索架在支撑杆顶部,而且每一层架设完毕后,缆索保持在上下两杆之间的设设计位置。

控制抬升的钢杆与索夹的施工工序与控制侧向位移的极为相似。索同样架在钢杆顶部,夹限制缆索位移。每层架完后人们将钢杆抽出,在架在刚安好的缆上。放松索夹,架好,如此重复施工直到完毕。

为测试体系的有效性,工程师测量架好索的高度,与理论值比较,结果总结在表2中。同样的测试架设索缆所需要的时间,表2中的结果显示,实际层高与理论层高从第二层开始不同,而且随层高加大。架完第十层,偏差以达4㎜,但偏差并不显著增加。

表1所示10号索实际与理论偏差略大于4号索。由于10号索还发生抬升,4号索只有

侧向位移。

如前所示,纺车从一个锚固区移到另一个大约要15分20秒,随层数增加架索时间减少,到第十层时只要13分钟左右,因此不会影响防线作业。

结论:

工程师们估计,悬索桥架设过程中会发生吊杆侧向移动,垂直移动,与设计位置偏离。通过一系列的试验,修正,尝试。工程师发现钢杆与索箍组合体系最为有效。一些细节问题如垫板长度等也得到检验。该体系在实际桥中得到成功应用。

参考文献:`

2019计算机一级考试试题及答案

计算机一级考试试题及答案(2) 第1 题第2 题第3 题第4 题第5 题 法律,依网络道德是指使用计算机时除______ 之外应当遵守的一法,守法,×0 些标准和规则。遵法20 世纪40 年代数字电子计算机的诞生,拉开了第5 次信息革命和______ 信息技术发展的序幕。在计算机的外部设备中,除外存储器:软盘、硬盘、光盘和磁带机等外,最常用的输入设备有键盘、_________。计算机软件分为系统软件和应用软件。打印机驱动程序属于______ 软件。从数据管理和通信的角度出发,数据又可以被看作是信息的______ 。现代×0 鼠标 ×0 系统 ×0 载体 ×0 第计算机系统由计算机软件和计算机硬件两大部分组成,其6 系统软件×0 中计算机软件又

可分为_________ 和应用软件。题第7 题第8 题常用的打印机有击打式、______ 式和激光打印机三种。喷墨×0 数据信号需要通过某种通信线路来传输,这个传输信号的通路叫_________。 信道 ×0 第CPU 与存储器之间在速度的匹配方面存在着矛盾,一般采外存,辅9 用多级存储系统层次结构来解决或缓和矛盾。按速度的快存,辅助×0 题慢排列,它们是高速缓存、内存、_________ 。存储第物质、能源和_________是人类社会赖以生存、发展的三10 大重要资源。题信息×0 第微波线路传输具有容量大、直线传播的特点,其缺点是易环境,电11 ×0 受______ 的影响、长途传输必须建立中继站。磁,干扰题第存储器分内存储器和外存储器,内存又叫_________,外12 存也叫辅存。题第信息处理技术就是对获取到的信息进行识别、13 _________ 、加工,保证信息安全、可靠地存储。题第计算机技术和_________相结合形成了计算机网络。主存,MAIN MEMORY ×0 转换,处×0 理通信技术×0 1

雅思历年真题口语题目汇总

雅思历年真题口语题目汇总 version 01old person describe an old man influenced you 1.who was he 2.when did you know him 3.what he did and explain why he influenced you part3 1.老人的经验有什么问题存在? 2.喜欢什么艺术品? 3.给老人拍照片时候注意什么呢? 4.你们国家对老年人是什么态度? 5.你认为这个社会在哪些方面对老年人不太好? 6.老人在你们家有什么影响? 7.你认为老年人在看问题的时候跟年轻人有什么不一样? 8.他们对大家有什么影响? version 02 city 1.where it is located? 2. what special for you? 3. why you want to stay there? part 3 1.please compare 100 hundred years old city and modern city and what predict about the city in the future. 2.上海是个怎样的城市 3.都有那些著名建筑

4.你想为这个城市做些什么? 5.有哪些现象有待提高或者那些提倡 version 03 room part2: 1.what's your favorite room in your home 2.what it likes you live 3.what you do in the room normally and explain why you like it part3: 1.你认识你的邻居吗? 2.城市里的房子和乡村有什么不同? 2003年9月换题后的口语topic Old person Describe a older person you know You should say:Who he or she is How you know him or her How he or she is And explain what infection he or she give you and in what aspect Further question: 1、你们国家对老年人是什么态度? 2、你认为这个社会在哪些方面对老年人不太好? 3、老人在你们家有什么影响? 4、你认为老年人在看问题的时候跟年轻人有什么不一样? 5、他们对大家有什么影响?

google搜索从入门到精通4.0

Google搜索从入门到精通 v4.0 (一) 1、前言 我是在2000年上半年知道GOOGLE的。在这之前,我搜索英文信息通常用AltaVista,而搜索中文信息则常用 Sina。但自使用了GOOGLE之后,它便成为我的Favorite Searchengine了。这也得感谢新浪网友曹溪,因为当初正是因为他的大力推介,才使我识得了GOOGLE。 记得1996年夏季的时候,当我第一次接触Internet,便被扑面而来的魔力征服了。那种天涯咫尺的感觉,真是妙不可言。在经历了疯狂的WWW冲浪和如痴如醉的BBS沉迷之后,我意识到Internet对我影响至深的还是在于学习方式的变迁。 如何来描述这种变迁呢?以前的学习,一般需要预先在肚子里存储下足够的知识,必要时,就从海量的信息中提取所需的部分。这种学习方式造就了很多“才高八斗,学富五车”的大才子。但是,到了信息领域大大超出“四书五经”的新时期,预先无目的的吞下海量信息的学习方式就有些不合时宜了。比方说,我们到了大型的图书城,往往有一种不知所措的感觉。旧有的学习方式需要变更以适应这个信息爆炸的年代。目的明确的去学习,即先知道要学什么,然后有目的的去寻找答案,这种方式看上去更加有效率。我不妨把这称为“即学式”,相应的,旧有的称为“预学式”。不过,“即学式”的实施是有前提的。首先,要求学习者拥有一个包罗万象的信息库,以供随时抽取各种目的信息;其次,是需要一个强劲的信息检索工具,以便高效率的从信息库中提取信息。很明显,Internet可以充当那个海量的信息库,而搜索引擎,则正是寻找光明之火的绝好工具。 “公欲善其事,必先利其器”。Internet只有一个,而搜索引擎则有N多个。有搜索高手说,所谓搜索,就是“在正确的地方使用正确的工具和正确的方法寻找正确的内容”。但是,对于普通人而言,掌握诸多搜索引擎的可能性似乎不大。用一两个相对强劲的具代表性的工具达到绝大多数搜索目的更为人们所迫切希望。不同的时期,涌现出不同的强者。就目前而言,我们非常幸运的有了: *****GOOGLE***** 2、摘要 本文简要的介绍了GOOGLE的历史和特点,GOOGLE的基本搜索语法和高级搜索语法,GOOGLE的特

剑桥雅思5 口语 Test4 Part3

雅思为各位考生推荐复习材料-剑 5 口语 Test4 Part3-Purpose of festivals and celebrations;需要本教程其他单元口语范文的考生请点击:剑 5 口语Test3 Part1-Entertainment;剑5 口语 Test3 Part2-Describe one of your friends;剑5 口语 Test3 Part3范文-Qualities of Friends。 PART 3: Purpose of festivals and celebrations Q: Why do you think festivals are important events in the working year? Answer: Yeah. It’s very important for two reasons. For the country, it’s a time to remember our cultural origin and our historical past. The whole country celebrates our root and it’s very inspiring. We become so proud of our past. I guess that’s why festivals are important. For the individual, festivals give us a chance for relaxation as we often have a few days off. It’s a time of fun, meeting friends, entertainment. So after that we feel like a new man. In a sense, holidays restore our balance between work and leisure. That’s also why we need festivals for China. Q: Would you agree that the original significance of festival is often lost today? 构思: 节日的初衷: 庆祝传统, 承上启下, 结束也是开始 现在的节日: 人们繁忙, 感觉不到开始和结束的意义, 过完节,马上就再次投入到工作中, 有些单位甚至连节假日都加班. 人们也不在那么感动传统,倒是好好的利用节日放松了一下,

2018年全国计算机一级考试题库及答案

2018年全国计算机一级考试题库及答案 1、计算机软件系统包括[ C ]。 A)程序和数据 B)编辑软件和应用软件 C)系统软件和应用软件 D)数据库软件和工具软件 2、计算机之所以能按照人们的意志自动进行工作,最直接的原因是采用了[ B ]。 A)二进制数值 B)存储程序思想 C)程序设计语言) D)高速电子元件 3、RAM的特点是[ A ]。 A)断电后,存储在其内的数据将会丢失B)存储在其内的数据将永久保存 C)用户只能读出数据,但不能写入数据D)容量大但存取速度慢 4、计算机病毒破坏的主要对象是[ D ]。 A)磁盘片 B)磁盘驱动器 C)CPU D)程序和数据 5、在计算机技术指标中,MIPS用来描述计算机的[ A ]。 A)运算速度 B)时钟频率 C)存储容量 D)字长 6、用八位二进位可以表示最大的十进制数为[ B ]。 A)256 B)255 C)1024 D)512 7、汉字国标码规定,每个汉字用[ B ]个字节表示。 A)1 B)2 C)3 D)4 8、在同一时刻,Windows系统中的活动窗口可以有[ D ]。 A)2个 B)255个 C)任意多个,只要内存足够 D)唯一一个 9、以下关于“回收站”的叙述中,不正确的是[ C ]。 A)放入回收站的信息可以恢复 B)回收站的容量可以调整 C)回收站是专门用于存放从软盘或硬盘上删除的信息

D)回收站是一个系统文件夹 10、以下关于“剪贴板”的说法中,不正确的是[ B ]。 A)剪贴板是内存的一块区域 B)剪贴板是硬盘的一块区域 C)剪贴板只可保留最后一次剪切或复制的内容 D)进行剪切或复制操作后重新启动计算机,剪贴板中的内容会消失 11.Excel的主要功能是( C )。 A. 表格处理,文字处理,文件管理 B. 表格处理,网络通讯,图表处理 C. 表格处理,数据库管理,图表处理 D. 表格处理,数据库管理,网络通讯 12.将十进制50转化为二进制数是( D )。 A. 110110 B. 101010 C. 110001 D. 110010 13.在Excel中,选定单元格后单击“复制”按钮,再选中目的单元格后单击“粘贴”按钮,此时被粘贴的是源单元格中的( B )。 A. 格式和公式 B. 全部 C. 数值和内容 D. 格式和批注 14.外存储器中的信息,必须首先调入( C ),然后才能供CPU使用。 A. 控制器 B. ROM C. RAM D. 运算器 15.关于Word中的文本框,下列说法(C )是不正确的。 A. 文本框可以做出冲蚀效果 B. 文本框可以做出三维效果 C. 文本框只能存放文本,不能放置图片 D. 文本框可以设置底纹 16.在Excel中,下列说法( D )是不正确的。 A. 可以对建立的图表进行缩放和修改 B. 可将单元格中的数据以各种统计图表的形式显示 C. 建立图表首先要在工作表中选取图表的数据区 D. 工作表中的数据源发生变化时,图表中的对应数据不能自动更新 17.在Word的"字体"对话框中,不可设定文字的(D )。

雅思历年真题口语题目汇总

雅思历年真题口语题目汇总 version01old person describe an old man influenced you 1.who was he 2.when did you know him 3.what he did and explain why he influeced you part3 1.老人的经验有什么问题存在? 2.喜欢什么艺术品? 3.给老人拍照片时候注意什么呢? 4.你们国家对老年人是什么态度? 5.你认为这个社会在哪些方面对老年人不太好? 6.老人在你们家有什么影响? 7.你认为老年人在看问题的时候跟年轻人有什么不一样? 8.他们对大家有什么影响? version02city 1.where it is located? 2.what special for you? 3.why you want to stay there? part3 1.please compare100hundred years old city and modern city and what predict about the city in the futu re. 2.上海是个怎样的城市 新东方批改网(https://www.360docs.net/doc/649472153.html,),在线雅思作文批改,雅思口语批改。语法纠错、恶补,制定考试计划,

3.都有那些著名建筑 4.你想为这个城市做些什么? 5.有哪些现象有待提高或者那些提倡 version03room part2: 1.what's your favorite room in your home 2.what it likes you live 3.what you do in the room normally and explain why you like it part3: 1.你认识你的邻居吗? 2.城市里的房子和乡村有什么不同? 2003年9月换题后的口语topic Old person Describe a older person you know You should say:Who he or she is How you know him or her How he or she is And explain what infection he or she give you and in what aspect Further question: 1、你们国家对老年人是什么态度? 2、你认为这个社会在哪些方面对老年人不太好? 3、老人在你们家有什么影响? 新东方批改网(https://www.360docs.net/doc/649472153.html,),在线雅思作文批改,雅思口语批改。语法纠错、恶补,制定考试计划,

如何成为金牌自由翻译(法磊)

?法磊推荐的书,网站 ●英语写作能力:《高级英语写作手册》(英文版北京外国语大学出版社) ●双语能力:英汉对照读物 ●做个知识渊博的杂家:1)先去国内各大门户网站了解一下新闻,再去 China Daily,新华网英文版了解英文的表达法,可以学到本土特色东西的表 达法。 2)浏览国外新闻网站,就同一个话题,摘取一段换,揣摩表达方法。 3)浏览论坛,如翻译中国,译网情深,https://www.360docs.net/doc/649472153.html,/ 4)《中国翻译》 5)http://blog.hjenglish/wuzhongdong北外教授博客 6)《Google 从入门到精通》 ?翻译路上的交通证(考证一方面是一种凭证,另一方面也是一种 学习过程) ●上海高级口译证书和CATTI笔译二级证书 ●参加比赛:韩素音青年翻译奖 CCTV希望之星英语风采大赛 ?翻译路上的工具 ●搜索引擎:1)缩略语的搜索:缩略语+所属范畴 专有名词的搜索:如,中国银行业监督管理委员会+bank 2)名言名句的翻译要事先搜索是否有更地道的翻译 3)对于不确定的搭配可利用搜索引擎搜索,如果超过20个网页有这样的 表达,且大多数为外国网站,则可以运用 4)小语种的翻译可以借助先转换为英语再转换为中文(资料少的情况下) 语种互译网站:https://www.360docs.net/doc/649472153.html,/translate-t ●TRADOS软件 ●专业术语在线词典:https://www.360docs.net/doc/649472153.html,/ ●word,excel,ppt,pdf,autocad(工科翻译)的熟练使用,包括排版 ?翻译中的思维与方法 ●以段为单位,理解大意后,再翻译每个句子,然后再从整段出发修改 句子。翻译的句子要考虑阅读者的思维习惯。 ●只要保证语义不变,句子形式、语法结构都可以改变。 ●翻译中的修改,1)先修改低级错误,如标点,错别字 2)对照原文逐句看翻译正确与否 3)抛开原文,看译文是否通顺 4)再对照 5)搁置几天后再修改 ●翻译初期,要先做英译中,学学正确的英语表达方法。

典型案例分析

铁山乡干部作风整治典型案例分析会 会议记录整理 时间:2012年4月24日 地点:乡便民服务中心五楼会议室 主持:彭联军(纪检书记) 4月24日上午,铁山乡党委政府在乡便民服务中心五楼会议室召开“集中整治干部作风突出问题活动”典型案例剖析专题会议,出席会议的有全体乡村干部、乡属乡办各单位的负责人。会议由乡纪委书记、集中整治影响发展环境的干部作风突出问题活动领导小组副组长彭联军同志主持。乡党委书记、集中整治影响发展环境的干部作风突出问题活动领导小组组长洪海出席会议并讲话。 一、典型案例分析 1、江西省赣州市石城县通报一起干部作风问题典型案件。 该县屏山镇长江村新村点近百户建房户2007年申请办证,至今年3月调查时仍未办结,对该镇政府、规划所、国土所相关人员办事拖拉、服务意识不强、不把群众利益放在首位的行为和驻村挂点的县体育局“送政策、送温暖、送服务”工作队员作风不实问题进行效能责任追究,给予3人口头效能告诫,扣发一个月津补贴的50%;给予4人书面效能告诫,扣发一个月津补贴,且当年度考核不能评为优秀等次;对建房办证中乱收费行为进行立案调查,给予1人党内严重警告、2人党内警告、2人行政警告处分。目前,该村建房户土地使用

证正在按程序办理中,违规收取的费用已全部退还给了建房户。 分析:江西省赣州市石城县屏山镇长江村新村点农民建房办证过程中有关部门单位存在的问题,暴露出乡政府及职能部门存在着政策宣传不力、惠民政策执行不到位、干部作风飘浮、办事效率不高等问题,它直接侵害了群众的利益,造成了不良社会影响。各部门、各单位尤其是各级领导干部一定要从中汲取教训,引以为戒。要切实维护群众合法权益,坚决制止农民建房乱收费行为。要以当前全县正在开展集中整治影响发展环境的干部作风突出问题活动为契机,不断加强干部作风建设。要积极开展“送政策、送温暖、送服务”工作,深入群众,切实解决群众的合理诉求。 2、河北兴隆县部分县直部门和乡镇党员干部严重违纪违法被查处。 2009年5月,河北省审计厅到兴隆县对该县2006至2008年财政决算情况进行审计,审计中发现兴隆县部分县直部门和乡镇存在较严重的违反财经纪律问题,省审计组陆续向承德市委移送案件线索83件。市委决定组成联合调查组进行调查核实。经过省审计组审计和市委调查组调查,发现被审单位存在三个方面的突出问题:一是监督查处工作不到位。二是资金、账户管理不严。三是资金支出随意性大,违规使用资金现象比较严重。该县挂兰峪镇原党委书记王庆国、原镇长司铁军采用收入不入账、虚打收条截留款项、虚开发票套取资金等方式,将该镇应收的承包费、县直部门拨付的项目款等合计364万元留作账外资金,并采取报销虚假单据的方式,从“小金库”中套取现

【雅思口语预测】雅思口语话题题库范文

【雅思口语预测】雅思口语话题题库范文 雅思口语精准预测刘薇简介环球雅思北京学校副校长最受欢迎口语教师授课时激情中透着温婉幽默里渗入励志秉承让学生 "轻松复习事半功倍"的教学理念。 从事雅思教学多年北京大学传播学硕士曾学术访问哈佛大学 耶鲁大学等世界顶尖名校。 著作《雅思九天口语高分之路》、《剑桥雅思全真试题原版解析8》。本月预测重点本预测适用于xx年4月雅思考试超高频和重回题库考题、一级重点、都是重点类别需要考生准备细致答案。二级重点考生考生准备思路即可。 Part 1 分类汇总一基本信息类 1. Name 什么名字,中文名含义,未来换吗 2. Study or work 上班还上学上学问专业或最喜欢学科上班工作内容,参加过培训吗,未来换工作吗 3. Hometown 家乡哪里,有什么特别的地方,未来想居住的地方 4. Weather 喜欢什么天气家乡天气,家乡天气今年的变化 5. Family 家庭情况,家庭时间如何度过,全家人喜欢一起做什么二衣食住行类 1. Living 住flat还是house,最喜欢的房间,如果重装修会怎么做 2. Building 喜欢什么建筑,你们国家的人更喜欢传统还是时尚建筑,未来建筑的发展 3.

Countryside 喜欢郊区吗,郊区与城市的区别,什么人喜欢郊区 4. Transport 家乡交通特点,公共交通和私人交通的优缺点,未 来如何改善 5. Boating 划过船吗,坐过船吗,好处,你们国 家水运多吗 6. Clothes and fashion 喜欢什么衣服,喜欢时 尚吗,时尚对生活的影响 7. Bags 平时背包包吗,什么类型的 宝宝,知道哪些包包,丢过包包吗 8. Keeping healthy and fit 如何保持健康,如何保持身材 9. Daily routine and favorite time in a day 典型的一天,一天中最喜欢的时间段 10. Sleeping 几点睡几点起,睡不着怎么办,如何培养好的睡眠习惯 三娱乐休闲 1. Music 喜欢什么类型音乐,喜欢在家听还是concert hall。会乐器吗,什么乐器。 2. dancing 会舞蹈吗,中国人喜欢什么舞蹈,传统舞蹈得到了 传承吗 3. photography 喜欢摄影吗,喜欢给别人拍还是别人 给你拍,喜欢收藏照片吗 4. painting 会画画儿吗,小孩子学 习绘画的好处,有什么绘画技巧吗 5. sport 最喜欢什么运 动,好处 6. museum 喜欢去博物馆吗,好处,博物馆该收费吗7. leisure and relaxation 喜欢什么休闲活动,跟谁,在哪 儿,好处,中国人都喜欢什么休闲 8. weekends 如何度过周 末,周末加班吗,老板应该给发工资吗 9. postcards 喜欢 ___吗,发给别人或者收到过吗,跟email的区别 10. public park 喜欢去公园吗,做什么,应该有更多公园吗四科技生活

剑桥雅思口语真题解析

剑桥雅思口语真题解析 Part 1: 1.1姓名 1. What’s your full name? 2. Can I have your name, please? 3. Are there any special meanings of your name? 4. Do you like your name? Why? 5. Do Chinese people like changing their names? 6. What kind of people in China like changing their names? 7. Is there any rule for Chinese people giving names to their children? 1.2故乡 My hometown is Guangzhou. It is the capital of Guangdong province in the southwest of China. It is a large industrial city. It is close to Hong Kong so a lot of the industries involve trade and retail. It is also a finance area. The people in Guangzhou are very genial and helpful, also are very easy to get around. If you lose your way and ask someone, he will give you the direction immediately, he can also give you a hand if you are in trouble. By the year 2011, it is believed that my hometown Guangzhou has become the economic center of China. 2. Where is it located? 3. How about the climate in your hometown? Which season do you like? In my hometown Guangzhou, the four seasons are not evident, which only has spring and summer. It is too hot in the summer and it is also humid in the winter. I like summer better, for we will go swimming and start our outdoor activities in the summer, it gives us pretty environment, which full of various kinds of colors. Another reason is that it is suitable for traveling around. 4. How about the people in your hometown? The people in my hometown Guangzhou are very genial and helpful, also are very easy to get around. People will always give you a hand with things. If you lose your way and ask someone, he will give you the direction immediately, he can also give you a hand if you are in trouble. 5. What do most people do in your hometown? 6. Oh yes. Even though Guangzhou is very modern, it has some interesting temples and streets. There is one called the Temple of Six Banyan Trees and it was built about 1500 years ago. There is also a famous cultural and commercial street in Guangzhou called Beijing Road. In this street, you can not only see a historic exhibition about different years roadbed, which has more than thousand histories, but also has many business shops sale almost all kinds of things. Besides, you can taste traditional snacks and refreshments or experience temples with /unusual special architectural style nearby. Anyway, it is an interesting place so worth to visit! 7. How about the style of the building in your hometown? 8. What is one of the greatest changes having taken place over the years? 9. What problems still exist in your hometown? 10. How to improve the situation in your hometown? 11. Where is Chinese population mainly distributed? 12. What changes have occurred in people’s dwelling? 1.3学习 1. Are you an employee or a student? (Are you working or studying?) 2. What is your major?

法律英语学习经验

法律英语学习经验 1、法律专业且英语较好,或英语专业,掌握一定法律知识。个人觉得前者比后者更容易学好法律英语。本人属于前者。 2、学习外语最重要的是工具书,学习法律英语也不例外,拥有一本好的工具书是非常重要的。下面推荐几本很不错的工具书。 (1) Black’s Law Dictionary (7th版) 布莱克法律辞典(第七版),1999年出版,共1738页,英文原版,价格697元,网络上有卖的。大些的法律书店也有卖的。 (2)牛津现代法律用语辞典 法律出版社引进的英文原版,共953页,价格170元。该书主要是对一些法律词语进行了语法、语义上的分析,比如同义词、近义词比较,一些词语的拼写不同等。 (3)元照英美法词典 价格是380元,质量在国内同类工具书中算是最好的,但也存在一些错误和不足。详见本论坛帖子《元照英美法词典》求疵。 以上三本工具书是我用过的,都很不错。下面是我没用过的,但其他专家推荐的: (4) Oxford Law Dictionary 牛津法律词典 (5) Merriam-Webster’s Law Dictionary 1996年版,16美元。 此外陈忠诚所著《英汉汉英法律用语辩证词典》也不错,有真材实料。至于其他的英汉、汉英法律辞典,最好别买,大概都是剪刀加浆糊的产物;人云亦云,有很多错误的,误人子弟。 宋雷也主编过一大部头的、与元照同样规模的法律英语词典,其内容还未仔细研读,在此不作评论。 如果大家没钱,可以用网上词典,在此推荐https://www.360docs.net/doc/649472153.html,,很不错的词典搜索引擎。

3、多读英文原版教材和文章,理解词的具体运用和英美法律制度,扩大词汇量。 4、多看他人有关文章、著作及有关法律的正式英文译本,去伪存真。前提是你的知识量足够大,能一眼看出其真伪对错。《中国翻译》、《上海翻译》、《中国科技翻译》经常刊载法律翻译方面的文章,可惜多为泛泛之作,少见精品。 关于如何学好法律英语,我的经验大体就这些。但如果要作一个好的法律翻译,这些显然是不够的,这又是另外一个话题了。 关于如何学好法律英语,每个人的基础不一样,学习的习惯也不一样,所以很难有一个"万精油"的方法。 这里仅有几点个人经验,供参考: 1.坚持看原版的法律新闻,最好的地方如下: https://www.360docs.net/doc/649472153.html,/ ,如果上网方便,最好每天去一次,哪怕是时间只够把新闻标题看完…… 2.坚持用原版的法律词典,最好的当然是black’s law dictionary,不过,这两个地方的法律词典也不 错:https://www.360docs.net/doc/649472153.html, ,https://www.360docs.net/doc/649472153.html, .当然,刚开始用原版的法律词典可能有些不习惯,从长远来看,这是非常有好处的。 3.坚持读原版的法律书籍, 4.坚持听原版的法律节目,cnn和abc及bbc每周都有与法律有关的节目,这些节目网上也可以收听,只不过要通过代理服务器,还好,这个网站可以访问:https://www.360docs.net/doc/649472153.html, , 只是这里的节目没有原文对照,听起来有些难。还有一些:坚持分析原版的案件,坚持用英语写读书笔记和日记,坚持用英语思考,用英语和朋友,和

剑桥雅思11口语 Test4 Part3

雅思为各位考生推荐复习材料-剑11口语 Test4 Part3-Different types of TV programmes,需要本教程其他单元的口语范文,请点击:剑11口语 Test3 Part1范文-Photographs;剑11口语 Test3 Part2范文-weather;剑11口语 Test3 Part3范文-Types of weather。 Discussion topics: Different types of TV programmes Example questions: What are the most popular kinds of TV programmes in your country? Why is this? Do you think there are too many game shows on TV nowadays? Why? Do you think TV is the main way for people to get the news in your country? What other ways are there? TV advertising Example questions: What types of products are advertised most often on TV? Do you think that people pay attention to adverts on TV? Why do you think that is? How important are regulations on TV advertising? 题目一:What are the most popular kinds of TV programmes in your country? Why is this? 1.结构提示: There are so many kinds of TV programmes are popular in my country The and are very popular TV programmes in my country for they targetas the main audience 2.要点提示: TV play/TV series/ups and downs in the plot/kill time/ amusing/down to earth/depict common people’s life 题目二:Do you think there are too many game shows on TV nowadays? Why? 1.结构提示: Exactlyhttps://www.360docs.net/doc/649472153.html,/ielts/cb11/ I don’t make a comment because I never see

2015年计算机一级考试试题及答案

2015年计算机一级考试试题及答案 一、单项选择题(每小题2分,共40分) 1. 计算机网络最突出的优点是( D )。 A、存储容量大 B、资源共享 C、运算速度快 D、运算精度高 2.在TCP/IP参考模型中,( B)是TCP/IP参考模型中的最低层,负责网络层与硬件设备间的联系。 A、数据链路层 B、网络接口层 C、表示层 D、应用层 3.为网络提供共享资源并对这些资源进行管理的计算机称为( B )。 A、网卡 B、服务器 C、工作站 D、网桥 4.( C )是专门为增强计算机网络安全性而创建的一种技术手段,它使得网络更加稳定和安全。 A、以太网技术 B、杀毒软件 C、防火墙技术 D、隔离 5.在IEEE 802标准中,哪种代表的是无线局域网?( B ) A、IEEE 802.10 B、IEEE 802.11 C、IEEE 802.12 D、IEEE 802.13 6.下面关于顶级域名的描述中,哪一个是错误的?( C) A、net代表网络支持中心 B、org代表各种非营利性组织 C、int代表网络中心 D、mil代表军事部门 7. Internet中采用了层次结构的( A )来协助管理IP地址。 A、 DNS B、 DHCP C、 WEB D、 FTTP 8.因特网主机(服务器或客户机)的域名采用多层分级结构,各级域名也按由低到高的顺序从左向右排列,其基本结构为( C )。 A、子域名?国家代码?域类型 B、国家代码?子域名?域类型 C、子域名?域类型?国家代码 D、子域名?国家代码?域类型 9.( C )是一种在普通电话线上进行高速传输数据的技术,它使用了电话线中一直没有被使用过的频率,所以可以突破调制解调器速度的极限。 A、以太网技术 B、分布式技术 C、 ADSL技术 D、交换式技术 10.系统对WWW网页存储的默认格式是( C )。 A、 PPT B、 TXT C、 HTML D、 DOC 11. IP地址190.168.12.120属于哪一类IP地址?( B ) A、A类 B、B类 C、C类 D、D类 12. WWW即World Wide Web我们经常称它为( B )。 A、因特网 B、万维网 C、综合服务数据网 D、电子数据交换 13.计算机通信协议中的TCP称为 ( A ) 。 A、传输控制协议 B、网间互联协议 C、邮件通信协议 D、网络操作系统协议 14.互联网上的服务基于一种协议,WWW服务基于( C )协议。 A、 POP3 B、 SMTP C、 HTTP D、 TELNET 15.无线局域网最主要的一个缺点是( B )。 A、速率较慢 B、结构复杂 C、成本高 D、安全问题 16. Telnet功能是( B )。 A、软件下载 B、远程登录 C、 WWW浏览 D、新闻广播

剑桥雅思9口语真题+解析Test3-Part3

剑桥雅思9口语真题+解析Test3-Part3 摘要:剑桥雅思9口语真题+解析Test3-Part3,剑桥雅思9Test3口语Part3讨论话题举例:Reasons for daily travel,有需要的同学抓紧时间下载吧! Discussion topics: Reasons for daily travel Example questions: · Why do people need to travel every day? 为什么人们每天都需要出行? 笨鸟雅思口语名师点题 本题询问人们为什么每天穿梭于各地。通常针对询问people的问题,可以相应列举出不同人群,如上班的人、上学的人、走亲访友的人、旅游的人等,同时针对某类人群适当进行拓展。 高分示例 People need to travel for lots of different reasons. Almost everybody has to travel to work, so they can earn money and provide for their families. If a person is lucky, then they will live very close to the place where they work, so they can travel on foot or by bicycle. Sometimes, however, people live very far away, so they must travel by bus, train, car, or even sometimes by plane or boat! Lots of people also travel to see friends and family members, who might live in a different city, or even a different country. But often people just like to travel for fun, to go to somewhere new, or to see a famous tourist site or place of natural beauty. 参考译文 人们有各种各样的理由来来往往。几乎每个人都要去上班,这样才能赚钱养家。幸运的人住的地方离工作单位很近,可以步行或者骑车去上班。但是,有时候,住的地方比较远的人就必须坐公交车、坐火车、开车,甚至坐飞机、坐船去上班。大部分人都会去异地甚至异国拜访朋友、看望家人。但是人们经常是出去玩,去探索新的地方,去看看著名的景点,去看看自然美景。 亮点表达 earn money 赚钱 tourist site 旅游景点 provide for 供养

html5开发从入门到精通+源码+课件!!!

DOCTYPE和字符集 在2.1.2节中通过新老DOCTYPE的对比,读者可以清晰地看到HTML 5在精简旧有结构上做出的努力。DOCTYPE在出现之初主要用于XML中,用作描述XML允许使用的元素、属性和排列方式。起初HTML借鉴了XML中DOCTYPE的使用方法,并赋予了新用法,如大家熟知的触发浏览器的标准模式。假使在制作一张页面时,没有设定DOCTYPE,则浏览器会以怪异模式状态进行处理(即Quirks模式),该模式与标准模式在盒模型、样式、布局等都存在较大差异。因此,DOCTYPE在制作页面时是不可或缺的部分。 在上一版本HTML 4标准中,DOCTYPE被分为3种模式: ?严格模式,即严格遵循W3C标准的模式,代码格式如下: [html]view plain copy 1. ?过渡模式,包含了W3C标准的内容,同时还可以使用不被W3C推荐的标签,如font、b等,而且不可以使用框架元素(即frameset元素),代码格式如下: [html]view plain copy 1. ?框架模式,可以使用框架元素,其他与过渡模式相同,代码格式如下: [html]view plain copy 1. 提示:旧有的HTML关于DOCTYPE标准,读者可以参看W3C官方文档说明,网页地址:https://www.360docs.net/doc/649472153.html,/TR/1999/REC-html401-19991224/struct/global.html#h-7.2。虽然之前版本的HTML对DOCTYPE做了重重规定,但真实情况却是浏览器会尽最大的可能渲染

相关文档
最新文档