Pre_Specification TM047XYHP02-00_V1.0

MODEL NO.:TM047XYHP02

ISSUED DATE:2012-9-5

VERSION:Ver1.0

■Preliminary Specification

□Final Product Specification

Customer:

Approved by Notes

SHANGHAI TIANMA Confirmed:

Prepared by Checked by Approved by

Sunty Jack Huang Hawkin_He

The information contained herein is the exclusive property of SHANGHAI TIANMA MICRO-ELECTRONICS Corporation,and shall not be distributed,reproduced,or disclosed in whole or in part without prior written

Table of Contents

Coversheet (1)

Table of Contents (2)

Record of Revision (3)

1General Specifications (4)

2Dimension (5)

3FPC PIN Assignment (9)

4Cell Process Rule (15)

5Electrical Specification (16)

6Optical Characteristics (17)

7Environmental/Reliability Test (20)

8Package drawing (21)

9Precautions For Use of LCD Modules (22)

The information contained herein is the exclusive property of SHANGHAI TIANMA MICRO-ELECTRONICS Corporation,and shall not be distributed,reproduced,or disclosed in whole or in part without prior written

Record of Revision

The information contained herein is the exclusive property of SHANGHAI TIANMA MICRO-ELECTRONICS Corporation,and shall not be distributed,reproduced,or disclosed in whole or in part without prior written

1General Specifications

Note1:Viewing direction for best image quality is different from TFT definition,there is a180degree shift.

Note2:Requirements on Environmental Protection:Q/S0002

Note3:Substrate represents TFT or CF side thickness.

Note4:LCD weight tolerance:+/-5%

The information contained herein is the exclusive property of SHANGHAI TIANMA MICRO-ELECTRONICS Corporation,and shall not be distributed,reproduced,or disclosed in whole or in part without prior written

2Dimension

2.1Outline Dimension

The information contained herein is the exclusive property of SHANGHAI TIANMA MICRO-ELECTRONICS Corporation,and shall not be distributed,reproduced,or disclosed in whole or in part without prior written

2.2FPC Detail

The information contained herein is the exclusive property of SHANGHAI TIANMA MICRO-ELECTRONICS Corporation,and shall not be distributed,reproduced,or disclosed in whole or in part without prior written

The information contained herein is the exclusive property of SHANGHAI TIANMA MICRO-ELECTRONICS Corporation,and shall not be distributed,reproduced,or disclosed in whole or in part without prior written 2.3Test Pad

The information contained herein is the exclusive property of SHANGHAI TIANMA MICRO-ELECTRONICS Corporation,and shall not be distributed,reproduced,or disclosed in whole or in part without prior written

3FPC PIN Assignment

3.1Pin Definition

The information contained herein is the exclusive property of SHANGHAI TIANMA MICRO-ELECTRONICS Corporation,and shall not be distributed,reproduced,or disclosed in whole or in part without prior written

The information contained herein is the exclusive property of SHANGHAI TIANMA MICRO-ELECTRONICS Corporation,and shall not be distributed,reproduced,or disclosed in whole or in part without prior written

The information contained herein is the exclusive property of SHANGHAI TIANMA MICRO-ELECTRONICS Corporation,and shall not be distributed,reproduced,or disclosed in whole or in part without prior written

The information contained herein is the exclusive property of SHANGHAI TIANMA MICRO-ELECTRONICS Corporation,and shall not be distributed,reproduced,or disclosed in whole or in part without prior written

The information contained herein is the exclusive property of SHANGHAI TIANMA MICRO-ELECTRONICS Corporation,and shall not be distributed,reproduced,or disclosed in whole or in part without prior written

The information contained herein is the exclusive property of SHANGHAI TIANMA MICRO-ELECTRONICS Corporation,and shall not be distributed,reproduced,or disclosed in whole or in part without prior written

4Cell Process Rule

4.1Seal Outline

The information contained herein is the exclusive property of SHANGHAI TIANMA MICRO-ELECTRONICS Corporation,and shall not be distributed,reproduced,or disclosed in whole or in part without prior written

5Electrical Specification

(1)Vcom must be adjusted to optimize display quality:cross talk,contrast ratio and etc.

(2)VGH is TFT gate on voltage

(3)VGL is TFT gate off voltage

The storage capacitance structure of this product is Cst(Storage on Common).

The low voltage level of VGL signal must be fluctuated with same phase as Vcom,in case of Storage on Gate structure.

(4)Environmental condition:25℃

The information contained herein is the exclusive property of SHANGHAI TIANMA MICRO-ELECTRONICS Corporation,and shall not be distributed,reproduced,or disclosed in whole or in part without prior written

The information contained herein is the exclusive property of SHANGHAI TIANMA MICRO-ELECTRONICS Corporation,and shall not be distributed,reproduced,or disclosed in whole or in part without prior written 6Optical Characteristics

6.1Optical Specification

Light Sourc:C-light(With NV Polarizer)Ta=25℃

Test Conditions:1.The ambient temperature is 25℃.2.

The test systems refer to Note1and Note2.

6.2Rubbing Direction

The information contained herein is the exclusive property of SHANGHAI TIANMA MICRO-ELECTRONICS Corporation,and shall not be distributed,reproduced,or disclosed in whole or in part without prior written

Note 1:Definition of optical measurement system.

The optical characteristics should be measured in dark room.After 5minutes operation,the optical properties are measured at

the center point of the LCD screen.All input terminals LCD panel must be ground when measuring the center area of the

panel.

Photo Panel

TFT-LCD Note 2:Definition of viewing angle range and measurement system.

viewing angle is measured at the center point of the LCD by CONOSCOPE(ergo-80)。

Fig.1Definition of viewing angle

The information contained herein is the exclusive property of SHANGHAI TIANMA MICRO-ELECTRONICS Corporation,and shall not be distributed,reproduced,or disclosed in whole or in part without prior written Note 3:Definition of contrast ratio

“White state “:The state is that the LCD should driven by Vwhite.“Black state”:The state is that the

LCD should driven by Vblack.V White :To be determined

V Black :To be determined.

Note 4:Definition of response time

The response time is defined as the LCD optical switching time interval between “White”state and “Black”state.Rise time (T ON )is the time between photo detector output intensity changed from 90%to 10%.And fall time (T OFF )is the time between photo detector output intensity changed from 10%to 90%.

Note 5:Definition of color chromaticity (CIE1931)

Color coordinates measured at center point of LCD.

The information contained herein is the exclusive property of SHANGHAI TIANMA MICRO-ELECTRONICS Corporation,and shall not be distributed,reproduced,or disclosed in whole or in part without prior written 7

Environmental /Reliability Test

No Test Item

Condition

Quantity

Remark

1High Temperature Operation 70℃,240Hr 52Low Temperature Operation

-20℃,240Hr

53High Temperature &High Humidity

Operation

60℃,90%RH,240Hr

104High Temperature Storage 80℃,240HR 55Low Temperature Storage -30℃,240HR

56Thermal Shock -30℃,80℃(30Min)24cycle 107Package Vibration Test 10~55Hz,1.5mm,X/Y/Z 6hours 1Packing 8

Packing shock

76cm /8Corner /6Face,1cycle

1

Packing 9Packing thermal shock 1Packing