IFR 26650-3000mAh-3.2V -磷酸铁锂电池规格书超详细版

IFR 26650-3000mAh-3.2V -磷酸铁锂电池规格书超详细版
IFR 26650-3000mAh-3.2V -磷酸铁锂电池规格书超详细版

地址:广东省深圳市坪山新区金荔科技园4栋

TEL:86(0)0755-2308 8336 FAX:86(0)0755-2308 8396 DATE: 2015/10/24

Cylindrical LIFEPO4 Battery

Specification

圆柱型磷酸铁锂电池规格书MODEL/型号: IFR 26650-3000mAh 3.2V

Prepared By/Date 编制/日期Checked By/Date

审核/日期

Approved By/Date

批准/日期

冯时春/2015.10.24

Customer Approval 客户批准

Signature

确认

Date

日期

Company Name:

公司名称:

Company Stamp:

客户印章:

--- 保密文件---

地址:广东省深圳市坪山新区金荔科技园4栋

TEL:86(0)0755-2308 8336 FAX:86(0)0755-2308 8396 DATE: 2015/10/24

Amendment Records (修正记录)

Edition (版本) Description

(记述)

Prepared by

(编制)

Approved by

(批准)

Date

(日期)

A First Publish 冯时春2015/10/24

地址:广东省深圳市坪山新区金荔科技园4栋

TEL:86(0)0755-2308 8336 FAX:86(0)0755-2308 8396 DATE: 2015/10/24

1 Scope(适用范围)

This specification is applied to the reference battery in this Specification that manufactured by Yinkai Power Technology Co., Ltd.

本说明书适用于本书中所提及的银凯动力科技有限公司制造的电池。

2 Product Specification(产品技术规格)

Table 1 (表1)

No. (序号)

Item

(项目)

General Parameter

(常规参数)

Remark

(备注)

1 Rated Capacity

(额定容量)

Typical

(标称容量)

3000mAh Standard discharge(0.2C

5

A)

after Standard charge

(标准充电后0.2C5A标准放电)

Minimum

(最小容量)

2850mAh

2 Nominal Voltage

(正常电压)

3.2V

Mean Operation Voltage

(即工作电压)

3 Voltage at end of

Discharge

(放电终止电压)

2.5V

Discharge Cut-off Voltage

(放电截止电压)

4 Charging Voltage

(充电电压)

3.65V

5 Internal Impedance

(内阻)

≤30mΩ

Internal resistance measured at

AC 1KH Z after 50% charge

(半电态下用交流法测量内阻)

The measure must uses the

new batteries that within one

week after shipment and cycles

less than 5 times

(使用出货后不到一个星期及循

环次数少于5次的新电池测量)

6 Standard charge

(标准充电)

Constant Current 0.2C5A

Constant Voltage 3.65V

0.01 C cut-off

(持续电流:0.2C5A

持续电压:3.65V

截止电流:0.01 C)

7 Standard discharge

(标准放电)

Constant current 0.2C5A

end voltage 2.5V

(持续电流:0.2C5A

截止电压:2.5V)

地址:广东省深圳市坪山新区金荔科技园4栋

TEL:86(0)0755-2308 8336 FAX:86(0)0755-2308 8396 DATE: 2015/10/24

Continuous the table 1 (续表1)

No. (序号)

Item

(项目)

General Parameter

(常规参数)

Remark

(备注)

8 Fast charge

(快速充电)

Constant Current 0.5C

Constant Voltage 3.65V

0.01 C cut-off

(持续电流:0.5C

持续电压:3.65V

截止电流:0.01 C)

9 Fast discharge

(快速放电)

Constant current 0.5C

end voltage 2.5V

(持续电流:0.5 C

截止电压:2.5V)

10 Maximum Continuous

Charge Current

(最大充电持续电流)

1.0 C

11 Maximum Continuous

Discharge Current

(最大放电持续电流)

1.5 C

12 Operation Temperature

Range

(工作温度范围)

Charge(充电): 0~45℃

60±25%R.H.

Bare Cell

(电池储存湿度范围)

Discharge(放电): -10~60℃

13 Storage Temperature

Range

(储存温度范围)

Less than 1 year: -20~25℃

(小于一年:-20~25℃)

60±25%R.H.

at the shipment state

(出货状态时的湿度范围)

less than 3 months: -20~40℃

(小于3个月:-20~40℃)

Less than 7 day : -20~65℃

(小于7天:-20~65℃)

14

Cell Dimension

(单体电芯尺寸)

High/高度:66.2±0.3 mm

Initial Dimension

(初始尺寸)

Diameter/直径: 26.0±0.25 mm

地址:广东省深圳市坪山新区金荔科技园4栋

TEL:86(0)0755-2308 8336 FAX:86(0)0755-2308 8396 DATE: 2015/10/24

3 Performance And Test Conditions (电池性能及测试条件)

3.1 Standard Test Conditions(标准测试条件)

Test should be conducted with new batteries within one week after shipment from our factory and the cells shall not be cycled more than five times before the test. Unless otherwise specified, test and measurement shall be done under temperature of 23±3℃and relative humidity of 45~85%. If it is judged that the test results are not affected by such conditions, the tests may be conducted at temperature 15~30℃and humidity 25~85%RH.

测试必须使用出厂时间不超过一个星期的新电池,且未进行过五次以上的充放电循环。除非特别说明,否则测试会在温度23±3℃,相对湿度45~85%的条件下进行。如果经鉴定测试结果不受上述条件影响,测试也可以在温度15~30℃,相对湿度25~85%RH的条件下进行。

3.2 Measuring Instrument or Apparatus(测量器具及设备)

3.2.1 Dimension Measuring Instrument(尺寸测量器具)

The dimension measurement shall be implemented by instruments with equal or more

precision scale of 0.01mm.

尺寸测量器具的精度等级应不小于0.01 mm 。

3.2.2 Voltmeter(伏特计)

Standard class specified in the national standard or more sensitive class having inner impedance more than 10kΩ/V

按照国家标准指定规格等级或采用灵敏度更高的,测量电压时内阻不应小于10kΩ/V。

3.2.3 Ammeter(安培计)

Standard class specified in the national standard or more sensitive class. Total external resistance including ammeter and wire is less than 0.01Ω.

按照国家标准指定规格等级或采用灵敏度更高的,包括电流表及电线在内的总外阻应小于0.01Ω。

3.2.4 Impedance Meter(电阻计)

Impedance shall be measured by a sinusoidal alternating current method(1kHz LCR meter).

内阻测试仪测量原理应为交流阻抗法(1kHz LCR)。

3.3 Standard Charge\Discharge(标准充放电)

3.3.1 Standard Charge :Test procedure and its criteria are referred as follows:

标准充电:测试过程及标准如下:

0.2C5A =600mA

Charging shall consist of charging at a 0.2C5A constant current rate until the cell reaches 3.65V. The cell shall then be charged at constant voltage of 3.65 volts while tapering the charge current. Charging shall be terminated when the charging current has tapered to 0.01 C. Charge time: Approx 5.5h, The cell shall demonstrate no permanent degradation when charged between 0 oC and 45 oC.

电池先0.2C5A恒流充至3.65V,当充电电流逐渐减小时再以3.65V恒压充至电流减小到0.01 C,充电时间大约为5.5个小时。在0℃-45℃内充电电池应没有永久损害。

3.3.2 Standard Discharge(标准放电)

0.2C5A =600mA

Cells shall be discharged at a constant current of 0.2 C5A to 2.5 volts @ 23o± 3C

电池以0.2 C5A恒流放电至2.5V @ 23o± 3C

3.3.3 If no otherwise specified, the rest time between Chare and Discharge amount to 30min.

如果没有特别说明,电池充放电间隔时间为30分。

地址:广东省深圳市坪山新区金荔科技园4栋

TEL:86(0)0755-2308 8336 FAX:86(0)0755-2308 8396 DATE: 2015/10/24

3.4 Appearance(外观)

There shall be no such defect as flaw, crack, rust, leakage, which may adversely affect commercial value of battery.

电池外观应没有划伤、破裂、污渍、生锈、漏液等影响市场价值的缺陷存在。

3.5 Initial Performance Test(初始性能测试)

Table 2(表2)

Item (项目)Test Method and Condition

(测试方法及条件)

Requirements

(要求)

(1) Open-Circuit

Voltage

(开路电压)The open-circuit voltage shall be measured

within 24 hours after standard charge.

(标准充电后24小时内测量开路电压)

≥3.3V

(2) Internal impedance

(初始内阻) Internal resistance measured at AC 1KHz after

50% charge.

(半充电状态下,测量其AC 1KHz下的交流阻抗)

≤30mΩ

(3) Minimal Rated

Capacity

(最小额定容量) The capacity on 0.2C5A discharge till the voltage

tapered to 2.5V shall be measured after rested

for 30min then finish standard charge.

(标准充电后,搁置30min,测量0.2C放电至2.5V

截止电压所放出的容量)

Discharge Capacity

(放电容量)

≥2850mAh

3.6 Temperature Dependence of discharge capacity(放电温度特性)

Cells shall be charged per 3.3.1 and discharged @0.2 C5A to 2.5 volts. Except to be discharged at temperatures per Table 3. Cells shall be stored for 3 hours at the test temperature prior to discharging and then shall be discharged at the test temperature. The capacity of a cell at each temperature shall be compared to the capacity achieved at 23 oC and the percentage shall be calculated. Each cell shall meet or exceed the requirements of Table 3.

电池按3.3.1规定充电。按表3的温度中放电,电池必须先在该试验温度中放置3个小时。在每一个温度中的放电容量应不小于表3的要求。

Table 3 (表3)

Discharge Temperature

(放电温度)

0℃23℃45℃60℃

Discharge Capacity(0.2 C5A)

(放电容量/0.2 C5A)

60% 100% 97% 95%

地址:广东省深圳市坪山新区金荔科技园4栋

TEL:86(0)0755-2308 8336 FAX:86(0)0755-2308 8396 DATE: 2015/10/24

3.7 Cycle Life and Leakage-Proof(循环寿命及漏液试验)

Table 4(表4)

No. (序号)

Item

(项目)

Criteria

(标准)

Test Conditions

(测试条件)

1

Cycle Life

(循环寿命)

Higher than 80% of the

Initial Capacities of the

Cells

(初始容量的80%)

Carry out 1500cycle

Charging/Discharging in the below

condition.

◆Charge: Standard Charge, per 3.3.1

◆Discharge: 0.2 C5A to 2.5V

◆Rest Time between

charge/discharge:30min.

◆Temperature:23±3℃

循环1500次

充放电按以下条件:

◆充电: 标准充电, 按3.3.1规定

◆放电: 0.2 C5A放至2.5V

◆搁置:30min.

◆温度:23±3℃

2 Leakage-Proof

(漏液试验)

No leakage

(visual inspection)

(没有漏液/目测)

After full charge with standard charge, store

at 60±3℃, 60±10%RH for 1 month.

标准充电条件下充满电后在温度60±3℃,湿

度60±10%RH下储存一个月

4. Mechanical characteristics and Safety Test(安全测试及机械特性)

Table 5(表5)(Mechanical characteristics)

No. (序号)

Items

(项目)

Test Method and Condition

(测试方法及条件)

Criteria

(标准)

1 Vibration

Test

振动测试

After standard charging, fixed the cell to vibration

table and subjected to vibration cycling that the

frequency is to be varied at the rate of 1Hz per

minute between 10Hz an 55Hz, the excursion of

the vibration is 1.6mm. The cell shall be vibrated

for 30 minutes per axis of X YZ axes.

将标准充电后的电芯固定在振动台上,沿X、Y、Z三

个方向各振动30分钟,振幅 1.6mm,振动频率为

10Hz~55Hz,每分钟变化1Hz。

No leakage

无泄漏

No fire

不起火

2 Drop Test

跌落测试

The cell is to be dropped from a height of 1 meter

twice onto concrete ground.

将标准充电后的电芯从1米高度跌落至混凝土地面2

No explosion,

No fire,no leakage

无爆炸、无起火、

无泄漏

地址:广东省深圳市坪山新区金荔科技园4栋

TEL:86(0)0755-2308 8336 FAX:86(0)0755-2308 8396 DATE: 2015/10/24

Table 6(表6)(Safety Test)

Item (项目)

Battery

Condition

(电池要求)

Test Method

(测试方法)

Requirements

(要求)

Crush (挤压试验)

Fresh,

Fully charged

(充满电的新电池)

Crush between two flat plates. Applied force is

about 13kN(1.72Mpa) for 30min.

(电池放置在两块平面金属板间,施加13KN

(1.72Mpa)的作用力,且持续保持30分钟)

No explosion,

No fire

(无起火无爆炸)

Short

Circuit (短路试验20℃)

Fresh,

Fully charged

(充满电的新电池)

Each test sample battery, in turn, is to be short-

circuited by connecting the (+) and (-) terminals of

the battery with a Cu wire having a maximum

resistance load of 0.1Ω.T ests are to be conducted

at room temperature(20±2℃).

(在常温下约20±2℃依次把每个样品电池的正

负极用铜线连接起来使电池外部短路--线路总电

阻不超过0.1Ω)

No explosion,

No fire

The Temperature

of the surface of

the Cells are

lower than 150℃

(无起火无爆炸

电池表面温度

应低于150℃)

Short

Circuit (短路试验60℃)

Fresh,

Fully charged

(充满电的新电池)

Each test sample battery, in turn, is to be short-

circuited by connecting the (+) and (-) terminals of

the battery with a Cu wire having a maximum

resistance load of 0.1Ω.T ests are to be conducted

at temperature(60±2℃).

(在常温下约60±2℃依次把每个样品电池的正

负极用铜线连接起来使电池外部短路--线路总电

阻不超过0.1Ω)

No explosion,

No fire

The Temperature

of the surface of

the Cells are

lower than 150℃

(无起火无爆炸

电池表面温度应

低于150℃)

Impact (冲击试验)

Fresh,

Fully charged

(充满电的新电池)

A 56mm diameter bar is inlayed into the bottom of

a 10kg weight. And the weight is to be dropped

from a height of 1m onto a sample battery and

then the bar will be across the center of the

sample.(用一条直径为56mm的圆棒放置在电

池中央,将一10Kg的重锤从1m的高度垂直落

下在电池的中心位置)

No explosion,

No fire

(无起火无爆炸)

Forced Discharge (过放试验)

Fresh,

Fully charged

(充满电的新电池)

Discharge at a current of 1 C5A for 2.5h.

(以1C 的电流放电2.5小时)

No explosion,

No fire

(无起火无爆炸)

地址:广东省深圳市坪山新区金荔科技园4栋

TEL:86(0)0755-2308 8336 FAX:86(0)0755-2308 8396 DATE: 2015/10/24

5. Cautions in use(谨慎使用)

To ensure proper use of the battery please read the manual carefully before using it.

(为确保正确使用电池,使用前请仔细阅读本细则)

. Handling(电池操作)

? Do not expose to, dispose of the battery in fire.(不要靠近和放置电池于火中)

?Do not put the battery in a charger or equipment with wrong terminals connected.

(在充电器或设备仪器中不要把电池接错电极)

?Avoid shorting the battery(避免电池短路)

?Avoid excessive physical shock or vibration.(避免电池过多的物理撞击和震动)

?Do not disassemble or deform the battery.(不要解剖和使电池变形)

?Do not immerse in water.(不要把电池浸泡在水中)

?Do not use the battery mixed with other different make, type, or model batteries.

(不要和其它不同类型的电池混和使用)

?Keep out of the reach of children.(放置电池于儿童不易接触的地方)

. charge and discharge(充电和放电)

?Battery must be charged in appropriate charger only.

(电池必须用适当的充电器充电)

?Never use a modified or damaged charger.(不要使用改装或损坏的充电器)

?Do not leave battery in charger over 24 hours.

(不要把电池放置于充电器超过24h)

. storage(储存)

?Store the battery in a cool, dry and well-ventilated area.

(应把电池置于凉爽、干燥及通风良好的区域)

. disposal(电池处理)

?Regulations vary for different countries. Dispose of in accordance with local regulations.(电池处理要符合当地的规定)

6 .Battery operation instruction(电池工作指南)

6.1 Charging(充电)

Charging current:Cannot surpass the biggest charging current which in this specification book stipulated。

(充电电流:不能超过规格书上规定的最大充电电流)

Charging voltage:Does not have to surpass the highest amount which in this specification book stipulated to decide the voltage。

(充电电压:不能超过规格书上规定的最大充电电压)

Charge temperature:The battery must carry on the charge in the ambient temperature scope which this specification book stipulated。

(充电温度:电池充电必须在规格书规定环境温度范围内)

Uses the constant electric current and the constant voltage way charge, the prohibition reverse charges. If the battery positive electrode and the cathode meet instead, can damage the battery。(使用持续电流和电压方式进行充电,禁止反向充电,否则会损害电池)

地址:广东省深圳市坪山新区金荔科技园4栋

TEL:86(0)0755-2308 8336 FAX:86(0)0755-2308 8396 DATE: 2015/10/24

6.2 Discharging current(放电电流)

The discharging current does not have to surpass this specification book stipulation the biggest discharging current, the oversized electric current electric discharge can cause the battery capacity play to reduce and to cause the battery heat。

(不要超过本规格书上规定的最大放电电流,太大的电流放电会导致容量变小及使电池发热)

6.3 Electric discharge temperature(放电温度)

The battery discharge must carry on in the ambient temperature scope which this specification book stipulated.

(电池放电必须在本规格书规定的环境温度范围)

6.4 Over-discharges(过放电)

After the short time excessively discharges charges immediately cannot affect the use, but the long time excessively discharges can cause the battery the performance, battery function losing. The battery long-term has not used, has the possibility to be able to be at because of its automatic flashover characteristic certain excessively discharges the condition, for prevented excessively discharges the occurrence, the battery should maintain the certain electric quantity。

(在短时间过放电然后立即充电不会影响电池的使用,但如果是长时间过放电会导致电池性能及电池功能丧失。电池长时间不使用,可能会有因它本身自动产生的电弧特性而必然的过放电情形,为防止电池过放电,电池应该保持一定的电量) 6.5 Storing the Batteries(储存电池)

The battery should store in the product specification book stipulation temperature range. If has surpasses above for six months the long time storage, suggested you should carry on additional charge to the battery。(电池应该储存在本产品规格书中规定温度范围。如果储存时间超过六个月,建议对电池进行额外充电。)

7. Period of Warranty(保质期)

The period of warranty is half a year from the date of shipment. YINKAI POWER guarantees to give a replacement in case of cells with defects proven due to manufacturing process instead of the customers abuse and misuse.

(保质期从出货之日起半年。如果是制造过程的缺陷而不是用户错用滥用造成的,本公司确保更换)

8.Other The Chemical Reaction(其它的化学反应)

Because batteries utilize a chemical reaction, battery performance will deteriorate over time even if stored for a long period of time without being used. In addition, if the various usage conditions such as charge, discharge, ambient temperature, etc. are not maintained within the specified ranges the life expectancy of the battery may be shortened or the device in which the battery is used may be damaged by electrolyte leakage. If the batteries cannot maintain a charge for long periods of time, even when they are charged correctly, this may indicate it is time to change the battery.

(电池是利用化学反应产生电量,电池性能会随时间变差,即使电池长时间储存而不使用。另外,各种各样的使用方法,像充电、放电及环境温度,等等不能在本规格书规定的范围时的情形,会减小电池的期望寿命,或者会使仪器设备由于电池漏液而损坏。即使充电正确,电池长时间不能再充电,那就要更换电池了。)

9.Note:Any other items which are not covered in this specification shall be agreed by both parties.

(注意:任何本产品规格书未包含的其它条款,应由双方协议确定。)

地址:广东省深圳市坪山新区金荔科技园4栋

TEL:86(0)0755-2308 8336 FAX:86(0)0755-2308 8396 DATE: 2015/10/24

10. Appearance& Dimension(产品外观尺寸):

Pack PVC

Pack PVC

D 26.0±0.25H 66.2±0.3Units/单位mm

Drawer 绘图Checked

审核

Approved

批准

Date

日期

IFR26650 DRAWING

Drawing ID/图号

锂电池规格书

储能型磷酸铁锂电池规格书STORAGE LiFePO4 BATTERY SPECIFICATIONS 客户名称(Customer): 产品型号(Type): CF12V80Ah 发行日期(Issuing Date):

1. 适用范围(Product Scope) 本规格书描述了锂离子二次电池的技术要求、测量方法、运输、储存及注意事项。 This Specification describes the requirements of the lithium ion rechargeable battery supplied by 2. 电池组特性 (Battery Group Specifications)

单只电芯曲线图feature curve for single cell 3. 技术要求(Technical Requirements) 测试条件(除特别规定) Testing Conditions (unless otherwise specified) 温度Temperature: 15~35℃ 相对湿度Relative Humidity: 45%~75% 大气压Atmospheric pressure: 86~106Kpa 充放电性能 (Electrical Characteristics)

环境性能 (Environmental Characteristic) 机械性能(Mechanical characteristics)

安全性能(Safe Characteristic)

4 电池组基本性能 (Basic Characteristics of Battery) 5 电池组保护功能要求 (Battery Required Protection Functions) To insure the safety, charger and the protection circuit shall be satisfied the items below. As safety device, please use in combination with the temperature fuse. The standard charge method is CC/CV (constant current/constant voltage) 为确保安全,充电器和保护电路应符合以下要求。同时请使用装有热熔保险丝的安全装置。标准充电方法为CC/CV(恒流/恒压)

锂电池规格书参照

聚合物锂离子电池 产品规格承认书 ::JD220768430F(500Ah) 品名: 品名 编制审核批准 客户确认 签名//日期客户名称//印章签名 客户名称 总部:北京神州巨电新能源技术开发有限公司 Beijing Globe Super Power New Energy Technology Development Corp. 地址:中国北京市海淀区上地3街9号嘉华大厦E座206 ADD:Rm E-206,Gem Tech-Center,No.9,3rd Street,Haidian Dist.,Beijing,P.R.China 86-10--82783543-816Fax:86-10 86-10--82780720-1073 Tel:86-10 工厂:河北神州巨电新能源科技开发有限公司 Hebei Globe Super Power New Energy Technology Development Corp. 地址:河北邢台市巨鹿县巨鹿工业园 Hebei i Province,P.R.China ADD:Industrial District,Ju Jul l u,Xiangtan,Hebe

产品规格承认书 目录 1.适用范围---------------------------------------------------------------------------------------------------------2 2.产品规格---------------------------------------------------------------------------------------------------2 3.电池性能检查测试-----------------------------------------------------------------------------------------2 4.外观尺寸图------------------------------------------------------------------------------------------------------3 5.使用指南--------------------------------------------------------------------------------------------------------3 6.其它事项------------------------------------------------------------------------------------------------------4 7.电芯处理须知---------------------------------------------------------------------------------------------------4

IFR 26650-12Ah 6.4V -2S4PIFR 14500-600mAh 3.2V磷酸铁锂电池规格书超详细版

地址:广东省深圳市坪山新区金荔科技园4栋 TEL:86(0)0755-2308 8336 FAX:86(0)0755-2308 8396 DATE: 2016/01/08 Cylindrical LIFEPO4 Battery Specification 圆柱型磷酸铁锂电池规格书MODEL/型号: IFR 26650-12Ah 6.4V(2S4P) Prepared By/Date 编制/日期Checked By/Date 审核/日期 Approved By/Date 批准/日期 冯时春/2016.01.08 Customer Approval 客户批准 Signature 确认 Date 日期 Company Name: 公司名称: Company Stamp: 客户印章: --- 保密文件---

地址:广东省深圳市坪山新区金荔科技园4栋 TEL:86(0)0755-2308 8336 FAX:86(0)0755-2308 8396 DATE: 2016/01/08 Amendment Records (修正记录) Edition (版本) Description (记述) Prepared by (编制) Approved by (批准) Date (日期) A First Publish 冯时春2016/01/08

地址:广东省深圳市坪山新区金荔科技园4栋 TEL:86(0)0755-2308 8336 FAX:86(0)0755-2308 8396 DATE: 2016/01/08 1 Scope(适用范围) This specification is applied to the reference battery in this Specification that manufactured by Yinkai Power Technology Co., Ltd. 本说明书适用于本书中所提及的银凯动力科技有限公司制造的电池。 2 Product Specification(产品技术规格) Table 1 (表1) No. (序号) Item (项目) General Parameter (常规参数) Remark (备注) 1 Rated Capacity (额定容量) Typical (标称容量) 12Ah Standard discharge(0.2C 5 A) after Standard charge (标准充电后0.2C5A标准放电) Minimum (最小容量) 11.4Ah 2 Nominal Voltage (正常电压) 6.4V Mean Operation Voltage (即工作电压) 3 Voltage at end of Discharge (放电终止电压) 5.0V Discharge Cut-off Voltage (放电截止电压) 4 Charging Voltage (充电电压) 7.3V 5 Internal Impedance (内阻) ≤120mΩ Internal resistance measured at AC 1KH Z after 50% charge (半电态下用交流法测量内阻) The measure must uses the new batteries that within one week after shipment and cycles less than 5 times (使用出货后不到一个星期及循 环次数少于5次的新电池测量) 6 Standard charge (标准充电) Constant Current 0.2C5A Constant Voltage 7.3V 0.01 C cut-off (持续电流:0.2C5A 持续电压:7.3V 截止电流:0.01 C) 7 Standard discharge (标准放电) Constant current 0.2C5A end voltage 5.0V (持续电流:0.2C5A 截止电压:5.0V)

锂电池规格书

1.概述 General 此型号2406S 155×90×50mm的铝质外壳充电器能在输出6A的情况下工作,具有反接保护功能。 Battery Charger 2406S 155×90×50mm can work normally under 6A and with reverse polarity protection. 2.主要参数 Main product specification

3.环境条件 Environmental condition 4.技术特征 Electrical characteristics 输入特征: Input characteristic 输出特征和充电模式: Output characteristic or charge stages 保护特征: Protection characteristics

充电指示 Charging indicator 5.安全性 Safety & EMC

备注:辨识A:在技术要求范围内,充电器功能正常; Remark: Discrimination A- Function OK under technical requirement range; 辨识R:只有由外部干扰信号引起的保护装置(保险丝)损坏,整个设备在更换保护装置和重设运行参数后才能正常工作,因机械性损坏和设备故障的设备却不能。 Discrimination R- Physical damage or failure of equipment are not allowed, but damage of protection device (fuse) caused by interference signal of outside is allowed, and the whole equipment can work normally after replacement of protection device and reset of running parameter 6.环境测试要求 Environmental testing requirements 7.机械特征

锂电池、磷酸铁锂电池类 名词解析

电池名词解释 最近发现有许多人对电池的专有名词有一些误解,因此笔者在此对这些名词做一些整理,希望能帮助大家正确的了解,而不要产生一些认知的误会。 一次电池 顾名思义为只可使用一次性的电池,当电池内以化学能转变为电能来提供电力,也无法透过充电或其它方式将原有电能补充回来,因此完全放电后将不可再使用,这是电化学反应为不可逆转。一般市面上常见的干电池、碳锌电池、碱性电池、水银电池、锌空气电池等,皆属此一次性电池。不同的一次性电池种类有不同的使用方式,但都局限于单次的使用。在制造上许多电池种类的原料使用及制程上所使用的材料具有污染性,对环境以及人体具有相当大的影响。 二次电池 二次电池是可以再重复使用的电池,可持续的充电、放电使用,二次电池一样是经过化学能转换成电能,但可以藉由充电方式,将电能重新转化成化学能,便可让电池再次使用,而使用的次数随着材料与设计有其差异性。市面上常见的有铅酸电池、胶体电池、镍镉电池、镍氢电池、锂离子电池、锂离子聚合物电池、磷酸铁锂电池等。不同种类的二次电池因为其额定电压、额定容量、使用温度以及安全性,

有其不同的使用。在制造上许多电池种类的原料使用及制程上所使用的材料具有污染性,对环境以及人体具有相当大的影响。 碳锌电池 碳锌电池又称碳锌干电池、碳性电池、碳性电芯,外壳由锌构成。既可以作为电池的容器,又可以作为电池的负极。碳锌电池是从液体Leclanche电池发展而来。传统或一般型以氯化铵为电解质;电池则通常是使用氯化锌为电解质的碳锌电池,是一般使用的廉价电池的一种改良版。电池的正极主要是由粉末状的二氧化锰和碳构成。电解液是把氯化锌和氯化铵溶于水中所形成的糊状溶液。碳锌电池是最便宜的原电池,因此成为很多厂商的首选,因为这些厂商所销售的设备中常常需要配送电池。锌碳电池可以用于遥控器、闪光灯、玩具或晶体管收音机等功率不大的设备。此电池正极的碳棒与二氧化锰中所混合的碳只负责引出电流,并不参与反应,正极实际参与还原反应并提供正电的是二氧化锰中的锰,因此,又称为锰锌电池、锌锰电池或锌-二氧化锰电池,也有简称锰干电池的。碳锌电池的电压为1.5V。 锌空气电池 锌空气电池(Zinc-air battery)是一类结构特殊的品种。负极采用了锌合金。而正极材料,则是空气中的氧。在储存时一般保持密封,所以基本上没有自放电。又称锌氧电池,有时也被称为锌空电池。由于锌空电池内部含有高浓度的电解质(氢氧化钾具有强碱性、强腐蚀

磷酸铁锂电池 18650-1500-3.2V中文规格书 蒋合你好

产品规格书 产品名称:锂离子电池 产品型号:HTCF18650-1500mAh-3.2V 制订:周会 审核:李涛 批准:

目录 1. 适用范围 (3) 2. 型号 (3) 3. 外观及尺寸 (3) 4. 主要技术参数 (3) 5. 性能曲线 (4) 6. 安全性能 (5) 7. 环境适应性能 (6) 8. 标准测试环境 (6) 9. 储存及其它事项 (6) 10. 电池使用操作注意事项 (6)

1. 适用范围 本产品规格书描述了海特电子集团有限公司(以下简称海特电子)生产的锂离子电池产品性能指标。 2. 型号 HTCF18650-1500mAh-3.2V 3. 外观及尺寸 项目尺寸(mm) 直径(Ф)18.2±0.1 高度(H)64.8±0.4 4. 主要技术参数 序号项目标准 备注 1 标称容量1500mAh 0.5C,(本型号1C电流值为1500mA) 2 容量范围1450~1550mAh 0.5C 3 标称电压 3.2 V 4 交流内阻≤60mΩ加PTC型 5 充电 条件 截止电压 3.65±0.05V 以0.5C恒流充电至3.65V,恒压充电至电 流降至0.01C截止截止电流0.01C 6 放电截至电压 2.5V 7 循环性能2000次1C充电/1C放电,容量保持率≥80%,100%DOD 8 最大持续放电电流 4.5A 9 脉冲放电电流10A,5s 10 工作温度充电:0°C ~ 55°C;放电:-20°C ~ 60°C 11 储存温度-20°C ~ 45°C 12 电池重量42g (约)

5. 性能曲线 18650-1500mAh-3.2V电池0.5C充放电曲线 2 2.22.42.62.83 3.23.43.63.80 200 400 600 800 1000 1200 1400 1600 1800 容量/mAh 电压/V 充电放电 18650-1500mAh-3.2V 不同倍率放电曲线 2 2.32.62.9 3.23.53.80 200 400 600 800 10001200140016001800 容量/mAh 电压/V 0.1C 0.2C 0.5C 1C 2C 3C 18650-1500mAh-3.2V 不同温度放电曲线(0.5C) 1 1.52 2.53 3.540 300 600 9001200 1500 1800 容量/mAh 电压/V 60℃30℃10℃0℃-10℃-20℃-40℃

NCM三原电池与磷酸铁锂电池参数比对

NCM三元锂电池与磷酸铁锂电池充放 电特性曲线比较 1.性能参数比较 参数阳光三星NCM三元电池(电芯94Ah)宁德时代磷酸铁锂电池 (120Ah) 单体电芯充电 特性曲线推荐标准的充电方式(充电电流为:)充电时间≤, 先恒流充电转恒压限流充电,最高充电至。电流小于 3A默认充满,退出充电模式。也支持快充电(充电电 流为:47A)时间小于2h。 从最低电压至(电池已经 充满)之间充速率特别快充电 过程耗时不足2h,充电电流 为60A。(此曲线与前者对比, 不能明确表征含义) 单体电芯放电 特 性([I=94/(1/=])恒流放电至终止可持续200分 满充电压开路电压约为,放电平台~时放电速度开始急剧加

曲 线 钟。放电倍率越小放出的实际容量就越多,因大倍 率放电时部分能量以热能形式损失。充满电开路电 压,放电平台在~(较宽), 快直至电压约为时电池放电结 束,整个放电过程约110min, 放电电流大小约为60A。(此曲 线与前者对比,不能明确表征含 义,未标明放电制度——放电倍 率、温度条件等) 单体电池 容量与温 度关系曲 线 阳光三星 25℃充1C放,(根据塔菲尔曲线 外推法),循环4200次,电池剩 余容量(EOl)80%。94Ah电池实 际使用时建议及以下 宁德时代新能源 1C放电,45℃下可以将电池电量 方完全,放电均匀效果最好。磷酸铁 锂电池的低温放电性能更差,所有的 电池在温度稍高时均能放出额定容量 的100%。应与前者同等条件对比,循 环寿命(该图不是循环寿命曲线)。 单体电池 充放电倍 率与容量 关系曲线 阳光三星宁德时代新能源

充2C放电池循环3300次电池容量保持率82%;以充放循环2000次电池容量保持率91%;以充1C放循环800次电池容量保持率97%。 结合循环次数和容量保持率,充放效果最佳。 25℃,充放电压为时电池容量放完;25℃,充1C放电压为时电池容量放96%; 25℃,充3C放电压为时电池容量放90%,总之放电倍率越高放电约不完全。 25℃,充情况充放电效果最佳。该图只是单体电芯不同放电倍率下的曲线,不能表征不同放电倍率下的循环寿命。

电池规格书模板

TEL:( 0752)3535208 FAX:( 0752)3761580 Date:2017-3-30 Specification Approval Sheet 产品规格承认书 Customer 客户名称:域拓 Model产品型号:4L Type 产品类型:Li-ion battery Specification产品规格:3.7V/1400mAH signed by client 客户签名 Confirmed确认: Checked 审核: Approved 批准: signed by manufacturer 生产商签名 Prepared 制定:肖泽建 Checked 审核: Approved 批准:丁明谊 AMENDMENT RECORDS

TEL:( 0752)3535208 FAX:( 0752)3761580 Date:2017-3-30 Modification Time Description Issued Date Approved By 0 New release2015-06-26

TEL:( 0752)3535208 FAX:( 0752)3761580 Date:2017-3-30 Catalogue 目录 1 .Battery type and scope电池型号和适用范围 (4) 1 . 1: model产品型号: (4) 1 . 2: scope适用范围:客户定义 (4) 2 . Basic character and compose of battery电池的基本特性及组成 (4) 2 . 1: fundamental performance parameter of battery电池基本性能参数: (4) 2 . 2: Main components and parts主要零部件 (6) 2 . 3: Regular performance and unfailing performance产品常规性能和可靠性能 (6) 2 . 4: Contour Dimension of the Battery电池外形尺寸 (11) 3 . Specifications of Parts零部件规格 (112) 3 . 1: fender保护板 (122) 3 . 2: general electric and protection characters一般电气与保护特征 (122) 3 . 2: electric schematic diagram of battery电池电路原理图: (133) 3 . 3 : PCB layout 电路布局图………………………………………………………………….错误!未定义书签。3 4 . Specifications of the Cells电芯规格 (144) Announcements注意事项 (155) Danger 危险 (155) Warnings 警告 (166) Announcements 注意事项 (167)

锂电池规格书

储能型磷酸铁锂电池规格书 STORAGE LiFePO4 BATTERY SPECIFICATIONS 客户名称(Customer): 产品型号(Type): CF12V80Ah 发行日期(Issuing Date): 1. 适用范围(Product Scope) 本规格书描述了锂离子二次电池的技术要求、测量方法、运输、储存及注意事项。 This Specification describes the requirements of the lithium ion rechargeable battery supplied by Prepared 制定 Checked 审核 Approved 批准

2. 电池组特性(Battery Group Specifications) Cell 电芯 Model规格型号IFP8081230-10Ah Capacity容量10 Ah Rated Voltage 标称电压 3.2 V Internal Resistance 内阻标准≤4 mΩ Combination Standard配组标准 A. 容差Capacity Difference≤1% B. 内阻Resistance()=1~2 mΩ C. 荷电保持能力Current-maintaining Ability≥90% D. 电压Voltage3.3~3.4V Combination Method组合方式4串8并4S 8P Pile Index 成品参数 Rated Capacity 标称容量80.0Ah Minimal Capacity最小容量(0.3C5A)80.0Ah Nominal Voltage额定电压12.0V Max. Charge Voltage 最大充电电压14.8 V Discharge cut-off voltage放电截止电压10.0V Charge Current充电电流5-10A Working Current工作电流10-20A Output and Inpu t输出端与输入端P+(red) / P-(black) Weight电池重量9.2Kg Dimension外形尺寸(L×W×H)168×260×132mm(不包含外露开关) Charge Method 适用充电 Standard标准5A×16hrs Quick快速20A×4hrs. Operating Temperature 适用温度 Charge充电0℃~45℃;32o F~113o F Discharge放电-20℃~60℃;-4o F~149o F

磷酸铁锂充电器规格书

360W-43.8V6A SPECIFICATION Manufacturer/制造商 业务/SALES核准/APPROVED BY设计/DESIGNED BY 韦丽彬/Tracy Wei李辉黄强 APPROVAL SIGNATURE/客户确认 核准/APPROVED BY审核/CHECKED BY检测/TESTED BY 澳博森国际有限公司 ABP INTERNATIONAL LIMITED TEL:86-0755-********FAX:86-0755-******** E-mail:tracy-wei@https://www.360docs.net/doc/ee15276983.html, 地址:深圳市宝安区沙井万丰第三工业区丰平路14号3楼B座ADD:No.3rd floor,14th building,fengpin Rord,3rdindu strial area,Wanfeng Village,Shajing Town,Bao'an District,Shenzhen City,Guangdong, China

Contents 1.General-------------------------------------------------------------------3 2.Main product specification--------------------------------------------3 3.Environmental condition----------------------------------------------3 4.Electrical characteristics-----------------------------------------------3 1).Input characteristics-----------------------------------------------------4 2).Output characteristics---------------------------------------------------4 3).Protection characteristics-----------------------------------------------4 4).Status(LED)indicato r--------------------------------------------------5 5).Charge curve-------------------------------------------------------------------6 5.Safety&EMC------------------------------------------------------------------6 6.Environmental testing requirements---------------------------------7 7.Mechanical characteristics--------------------------------------------------7 1).Input terminator diagram&definition--------------------------------------8 2).Output terminator diagram&definition------------------------------------8 3).WEIGHT:(ABOUT2.6Kg)----------------------------------------------8 8.Package,transportation&storage-------------------------------------9 9.Reliability requirements----------------------------------------------9 10.Charger wiring-------------------------------------------------------9 11.Mechanical outline--------------------------------------------------------10

磷酸铁锂 IFR26650-3000mah 3.2V规格书

https://www.360docs.net/doc/ee15276983.html,/ MODEL:IFR26650 Li-Fe battery Specification 磷酸铁锂电池 规格书 Model/型号: IFR26650 Capacity/容量:3000mAh Voltage/电压:3.2V Prepared By/Date 编制/日期 Checked By/Date 审核/日期 Approved By/Date 批准/日期

https://www.360docs.net/doc/ee15276983.html,/ MODEL:IFR26650 Amendment Records (修正记录) Edition (版本)Description (记述) Prepared by (编制) Approved by (批准) Date (日期) A First Edition

https://www.360docs.net/doc/ee15276983.html,/ MODEL:IFR26650 1 Scope(使用范围) This specification is applied to the reference battery in this Specification and manufactured by Shenzhen Mottcell Battery Technology Co.,Ltd. 本规格书适用于本书中所提及的深圳市山木电池科技有限公司制造的电池。 2 Product Specification(产品技术规格) Table 1(表1) No. (序号) Item (项目) General Parameter (常规参数) Remark (备注) 1 Rated Capacity (额定容量) Typical (标称容量) 3000mAh Standard discharge(0.2C5A) after standard charge (标准充电后0.2C5A标准 放电) Minimum (最小容量) 2980mAh 2 Nominal Voltage (正常电压) 3.2V Mean Operation Voltage (即工作电压) 3 V oltage at end of Dischargr (放电终止电压) 2.0V Discharge Cut-off Voltage (放电截止电压) 4 Charging at end of Voltage (充电最高电压) 3.65V 5 Standard charge (标准充电) Constant Current 0.2C5A Constant V oltage 3.65V 0.02C5A cut-off (持续电流:0.2C5A 持续电压:3.65V 截止电 流:0.02C5A) Charge time:Approx 6.0h (充电时间:大约6个小时) 6 Standard discharge (标准放电) Constant Current 0.2C5A end V oltage 2.0V (持续电流:0.2C5A 截止电压2.0V) 7 internal impedance (内阻) R≤30mΩ

锂电池规格书

充电器规格书 Specification of Battery Charger 型号:ES2406S 6A锂电池充电器 (全铝外壳) / 6A Li Iron/Li Polymer BATTER Y CHARGER 1?概述 Gen eral 此型号2406S 155X 90X 50m啲铝质外壳充电器能在输出6A的情况下工作,具有反接保护功能。 Battery Charger 2406S 155 X 90 X 50nam work normally under 6A and with reverse polarity protection. 2.主要参数 Main product specificati on

3.环境条件 4.技术特征 Electrical characteristics 输入特征: 输出特征和充电模式: 保护特征:

充电指示 5.安全性 备注:辨识A :在技术要求范围内,充电器功能正常; Remark: Discrim in ati on A- Function OK un der tech ni cal requireme nt ran ge; 辨识R:只有由外部干扰信号引起的保护装置(保险丝)损坏,整个设备在更换保护装置和重设运行参数后才能正常工作,因机械性损坏和设备故障的设备却不能。

Discrimination R- Physical damage or failure of equipment are not allowed, but damage of protection device (fuse) caused by interferenee signal of outside is allowed, and the whole equipme nt can work n ormally after replaceme nt of protect ion device and reset of running parameter 6.环境测试要求 7.机械特征 Mecha ni cal characteristic: 外壳材质:铝 Shell material: Alumi num 外壳尺寸:长*宽*高=155X 90X 5毫米 Outline dimension: L*W*H= 155 X 90 xmm 输入接口:通过IEC标准 In put socket: meets IEC sta ndard 电源线:1.5米长 AC wires: 1.5m length 输出线:米长 DC wire: 1.0m len gth 净重:千克 Net Weight: 0.9Kg

磷酸铁锂电池组48V16A 规格书 蒋合你好

生效日期:2014-06-24 锂离子动力电池 产品规格书 产品名称:磷酸铁锂电池组 产品规格: 48V16Ah(18650) 制定审核批准 孔永乐任鹏任士界

生效日期:2014-06-24 目录 1. 前言 (3) 2. 产品规格及型号 (3) 3. 电池组相关参数 (4) 4.标准测试条件 (4) 5.充放电特性 (5) 6. 充放电曲线 (5) 7. 注意事项 (6) 8. 产品责任 (6)

生效日期:2014-06-24 1. 前言 本标准描述了磷酸铁锂48V16Ah电池组的外型尺寸、特性、技术要求及注意事项,本标准适用于磷酸铁锂48V16Ah电池组。 2. 产品规格及型号 2.1产品规格: 锂离子电池组 2.2型号: 16IFR48-16-Y (18650- 3.2V-16S10P) 2.3相关图片及出线方式(以实物为准) 正极输出红色一根14号线线长(500±10)mm 威浦WS20系列两芯防 水航空接插件(1正2负)负极输出黑色一根14号线线长(500±10)mm

生效日期:2014-06-24 3.电池组相关参数 项目标准备注 标称电压48V 典型容量16±0.5Ah 0.2C放电率 正常电流15A 最大持续放电电流30A <2min 最大瞬间放电电流120±20A 10±5ms 放电截止电压约40V 充电电压57.6±0.1V 充电方式CC/CV,请用专用充电器充电充电电流≤10A 内阻≤100mΩ放电正极和放电负极两端之间内阻工作温度范围 充电0℃~+45℃ 放电 -20℃~+60℃ 当环境温度大于45℃时,请注意通风散热 存储温度范围 0℃~40℃ (容量80%) 长期存储温度在 15℃~25℃ 储存使用环境湿度5%≤RH≤85% 包装材质PVC 重量7.2±0.1Kg 外部尺寸(385±2)*(150±2)*(75±2)mm 保护功能过充保护、过放保护、过流保护、均衡功能、温度保护4.标准测试条件 测试电池组必须是本公司出厂时间不超过一个月。 本规格书中各项试验应在标准大气条件下进行:.温度:25℃±5℃;相对湿度:65±20% .

磷酸铁锂电池组技术规范

中国**通信集团江西有限公司上饶分公司2013年磷酸铁锂电池组公开招投标项目技术规范 一、技术规范情况: 一、概述 1、本技术要求为江西**通信集团上饶分公司后备电源招标文件技术 规范书。 2、本技术规范书的编制依据是根据中国信息产业部“通信局(站)电源 系统的总技术要求”等有关规定编制。 3、参与选型及报价的设备必须符合本技术规范书的要求,如相关要 求低于本技术规范书的要求应论述其理由。 4、投标方必须对所有供货质量和服务质量负责,即:保证所有供货 符合技术要求、服务质量要求、交货验收要求、价格规定要求。 5、投标方必须对本技术规范书的每一款做出明确答复,并给出详细 的技术数据和指标。 6、投标方应详尽叙述所推荐产品的其它技术性能。生产商应具有完 善的检测手段及相应的检测设备。 7、投标方以中文书面形式提供设备的全套技术文件及文件清单。提 供的技术文件数量为2套纸质文件和1套电子文档。技术文件内容要与提供的设备一致,因投标设备软硬件修改而导致文件的任何修改,厂商应提供修改或补充的印刷文件。所有的文件均应有简洁明了的名称和编号,各种文字说明应通俗易懂,所有图纸和图形符号等均应规范化。投标方应提供设备说明书、企业内部检测标准、通讯协议、安装、维护和操作手册等。提供产品检验报告、产品合格证。 8、设备说明书包括设备工作原理、技术性能、功能、指标、结构(容 量、尺寸和重量)、接线及控制原理图、设备可靠性指标等。安装、维护和操作手册包括安装手册、维护操作手册、备品备件清单等。 9、投标方负责提供设备及所有附件的供应、运输,在开通、调试及

验收直至交付使用的过程中提供免费技术指导、人员培训以及设备安装及相应保修。 10、本招标文件解释权属于江西**上饶分公司。 二、范围 1、本次招标的设备为以铁锂电池作为后备电池的后备电源系统,包 括如下设备: ①磷酸铁锂电池组(磷酸铁锂电池组容量为50AH;具备电池管理 系统BMS功能)。铁锂电池采取壁挂方式安装。 ②交直流一体化UPS电源。 ③壁挂式机柜、防雷模块、空开。 2、本技术规范适用于为实现各类小功率通信终端设备的远程供电的 通信用静止型电源。其主要负载包括微蜂窝、WLAN设备、光纤通信网络设备、室内分布系统以及室外边际站、射频拉远等。 三、系统主要技术指标 主要技术性能指标: ●工作温度:-20℃~+60℃(注:工作温度范围内,电池外观应 无变形、无爆裂等现象) ●贮存温度范围:-25℃~+60℃ ●相对湿度:≤85% ●大气压力:70KPa~106Kpa ●工作电压:-48V~-56V ●音频噪音:<55dB(设备正面1米处) 四、设备性能如下: 电池组(磷酸铁锂电池组): 1、蓄电池容量为50AH,每组-48V电池组内必须有15或16节单体电池组成,具备电池管理系统BMS功能。 电池自维护:具备电池自动均衡功能;产品应具备监控功能,具有RS232或RS485接口,可接入买方的动力环境监控系统。投标方应免费提供相关监控协议。 充放电自动管理:监控单元自动测量电池的充放电电流并对电池

IFR 14500-450mAh 3.2V磷酸铁锂电池规格书超详细版

地址:省市坪山新区金荔科技园4栋 DATE: TEL:86(0)0755-2308 8336 FAX:86(0)0755-2308 8396 2015/11/04

地址:省市坪山新区金荔科技园4栋 TEL:86(0)0755-2308 8336 FAX:86(0)0755-2308 8396 DATE: 2015/11/04 Amendment Records (修正记录) Edition (版本) Description (记述) Prepared by (编制) Approved by (批准) Date (日期) A First Publish 时春2015/11/04

地址:省市坪山新区金荔科技园4栋 TEL:86(0)0755-2308 8336 FAX:86(0)0755-2308 8396 DATE: 2015/11/04 1Scope(适用围) This specification is applied to the reference battery in this Specification that manufactured by Yinkai Power Technology Co., Ltd. 本说明书适用于本书中所提及的银凯动力科技制造的电池。 2Product Specification(产品技术规格) Table 1 (表1) No. (序号) Item (项目) General Parameter (常规参数) Remark (备注) 1 Rated Capacity (额定容量) Typical (标称容量) 450mAh Standard discharge(0.2C 5 A) after Standard charge (标准充电后0.2C5A标准放电) Minimum (最小容量) 450mAh 2 Nominal Voltage (正常电压) 3.2V Mean Operation Voltage (即工作电压) 3 Voltage at end of Discharge (放电终止电压) 2.0V Discharge Cut-off Voltage (放电截止电压) 4 Charging Voltage (充电电压) 3.65V 5 出货电压≥3.28V 6 Internal Impedance (阻) ≤130mΩ Internal resistance measured at AC 1KH Z after 50% charge (半电态下用交流法测量阻) The measure must uses the new batteries that within one week after shipment and cycles less than 5 times (使用出货后不到一个星期及循 环次数少于5次的新电池测量) 7 Standard charge (标准充电) Constant Current 0.2C5A Constant Voltage 3.65V 0.01 C cut-off (持续电流:0.2C5A 持续电压:3.65V 截止电流:0.01 C) 8 Standard discharge (标准放电) Constant current 0.2C5A end voltage 2.0V (持续电流:0.2C A

相关文档
最新文档