足球常用语中英文对照
The World cup 世界杯
the European Championship或者European Cup 欧洲杯Championship Cup 冠军杯
field / pitch 足球场
midfield 中场
backfield 后场
kickoff circle / center circle 中圈
halfway line 中线
touchline / sideline 边线
goal line 球门线
end line 底线
penalty mark (点球)罚球点
penalty area 禁区(罚球区)
goal area 小禁区(球门区)
球队称谓篇
coach 教练
head coach 主教练
football player 足球运动员
referee 裁判
lineman 巡边员
captain / leader 队长
forward / striker 前锋
midfielder 前卫
left midfielder 左前卫
right midfielder 右前卫
attacking midfielder 攻击型前卫(前腰)defending midfielder 防守型前卫(后腰)center forward 中锋
full back 后卫
center back 中后卫
left back 左后卫
right back 右后卫
sweeper 清道夫,拖后中卫
goalkeeper / goalie 守门员
cheer team 拉拉队
足球技术篇
kick-off 开球
bicycle kick / overhead kick 倒钩球
chest-high ball 半高球
corner ball / corner 角球
goal kick 球门球
handball 手球
header 头球
penalty kick 点球
place kick 定位球
own goal 乌龙球
hat-trick 帽子戏法
free kick 任意球
direct free kick 直接任意球indirect free kick 间接任意球stopping 停球
chesting 胸部停球
pass 传球
short pass 短传
long pass 长传
cross pass 横传
spot pass 球传到位consecutive passes 连续传球take a pass 接球
triangular pass 三角传球
flank pass 边线传球
lobbing pass 高吊传球
volley pass 凌空传球
slide tackle 铲球
rolling pass / ground pass 地滚球flying header 跳起顶球clearance kick 解围
shoot 射门
close-range shot 近射
long shot 远射
offside 越位
throw-in 掷界外球
block tackle 正面抢截
body check 阻挡
fair charge 合理冲撞
diving header 鱼跃顶球dribbling 盘球,带球
clean catching (守门员)接高球finger-tip save (守门员)托救球offside 越位
deceptive movement 假动作break through 突破
kick-out 踢出界
足球战术篇
set the pace 掌握进攻节奏
ward off an assault 击退一次攻势break up an attack 破坏一次攻势disorganize the defense 搅乱防守total football 全攻全守足球战术
open football 拉开的足球战术
off-side trap 越位战术
wing play 边锋战术
time wasting tactics 拖延战术
4-3-3 formation 433阵型
4-4-2 formation 442阵型
beat the offside trap 反越位成功
foul 犯规
technical foul 技术犯规
break loose 摆脱
control the midfield 控制中场
set a wall 筑人墙
close-marking defense 盯人防守
比赛方式篇
half-time interval 中场休息
round robin 循环赛
group round robin 小组循环赛
extra time 加时赛
elimination match 淘汰赛
injury time 伤停补时
golden goal / sudden death 金球制,突然死亡法eighth-final 八分之一决赛
quarterfinal 四分之一决赛
semi-final 半决赛
final match 决赛
preliminary match 预赛
one-sided game 一边倒的比赛competition regulations 比赛条例disqualification 取消比赛资格match ban 禁赛命令
doping test 药检
draw 抽签
send a player off 判罚出场
red card 红牌
yellow card 黄牌
goal 球门,进球数
draw 平局
goal drought 进球荒
ranking 排名(名次)
FIFA:The Federation internation de Football Association(国际足联)
red card 红牌
yellow card 黄牌
The goal is disallowed. 进球无效。foul 犯规
goal kick 球门球
hand ball 手球
header 头球
penalty kick 点球
fair charge 合理冲撞
close-marking defence 盯人防守deceptive movement 假动作
to shoot 射门
mishit 未射中
offside 越位to pass the ball 传球
to break through 带球过人
to set a wall 筑人墙
hat trick 帽子戏法
time wasting tactics 拖延战术cheering squad 拉拉队
locker room (运动员)休息室、更衣室nation team 国家队
coach 教练
Stop holding. 不许拉人。
Stop pushing. 不许推人。
Don't hold up the game.不要延误时间。match fixing 非法操纵比赛
重温球场常用语
elimination match ,knock-out 淘汰赛competition rules 比赛规则
close watch 紧盯人战术)
protest 对不公平裁判的抗议
offside 越位
first(second )half 上(下) 半场overhead throw 过顶掷球indicator, score board 记分牌sliding tackle 铲球
kick off 开球
sellout 球票卖完
free kick 任意球
throw in 掷界外球
wall 人墙
riot 球场骚乱
corner kick 角球
handclap 鼓掌
yell 观众的喊声
hat-trick 帽子戏法draw 平局
direct(indirect)kick 直接(间接)球eighth-finals 八分之一决赛
semi-final 半决赛
quarterfinal 四分之一决赛
first round 第一轮
one-sided game 一边倒的比赛round-robin 循环赛
competition regulations 比赛条例doping test 药检disqualification 取消比赛资格draw,sortition 抽签sportsmanship 运动员的道德风格overhead kick 倒勾球
match ban 禁赛命令
relegation 降级
ranking 排名,名次
grouping 分组
schedule 比赛日程
heading 顶球
half time 中场休息stopping 停球kick-out 踢出界sending-off 罚下场place kick 定位球pass 传球
场地名称篇
field / pitch 足球场
midfield 中场
backfield 后场
kickoff circle / center circle 中圈halfway line 中线
touchline / sideline 边线goal line 球门线
end line 底线
penalty mark (点球)罚球点penalty area 禁区(罚球区)goal area 小禁区(球门区)
球队称谓篇
coach 教练
head coach 主教练
football player 足球运动员
referee 裁判
lineman 巡边员
captain / leader 队长
forward / striker 前锋
midfielder 前卫
left midfielder 左前卫
right midfielder 右前卫
attacking midfielder 攻击型前卫(前腰)defending midfielder 防守型前卫(后腰)
center forward 中锋
full back 后卫
center back 中后卫
left back 左后卫
right back 右后卫
sweeper 清道夫,拖后中卫goalkeeper / goalie 守门员
cheer team 拉拉队
足球技术篇
kick-off 开球
bicycle kick / overhead kick 倒钩球chest-high ball 半高球
corner ball / corner 角球
goal kick 球门球
handball 手球
header 头球
penalty kick 点球
place kick 定位球
own goal 乌龙球hat-trick 帽子戏法
free kick 任意球
direct free kick 直接任意球indirect free kick 间接任意球stopping 停球
chesting 胸部停球
pass 传球
short pass 短传
long pass 长传
cross pass 横传
spot pass 球传到位
consecutive passes 连续传球take a pass 接球
triangular pass 三角传球
flank pass 边线传球
lobbing pass 高吊传球
volley pass 凌空传球
slide tackle 铲球
rolling pass / ground pass 地滚球flying header 跳起顶球clearance kick 解围
shoot 射门
close-range shot 近射
long shot 远射offside 越位
throw-in 掷界外球
block tackle 正面抢截
body check 阻挡
fair charge 合理冲撞
diving header 鱼跃顶球dribbling 盘球,带球
clean catching (守门员)接高球finger-tip save (守门员)托救球offside 越位
deceptive movement 假动作break through 突破
kick-out 踢出界
足球战术篇
set the pace 掌握进攻节奏
ward off an assault 击退一次攻势break up an attack 破坏一次攻势disorganize the defence 搅乱防守total football 全攻全守足球战术open football 拉开的足球战术
off-side trap 越位战术
wing play 边锋战术
time wasting tactics 拖延战术4-3-3 formation 433阵型
4-4-2 formation 442阵型
beat the offside trap 反越位成功foul 犯规
technical foul 技术犯规
break loose 摆脱
control the midfield 控制中场set a wall 筑人墙
close-marking defence 盯人防守
比赛方式篇
half-time interval 中场休息
round robin 循环赛
group round robin 小组循环赛
extra time 加时赛
elimination match 淘汰赛
injury time 伤停补时
golden goal / sudden death 金球制,突然死亡法
eighth-final 八分之一决赛quarterfinal 四分之一决赛
semi-final 半决赛
final match 决赛
preliminary match 预赛
one-sided game 一边倒的比赛competition regulations 比赛条例disqualification 取消比赛资格match ban 禁赛命令doping test 药检
draw / sortition 抽签send a player off 判罚出场red card 红牌
yellow card 黄牌
goal 球门,进球数
draw 平局
goal drought 进球荒ranking 排名(名次)
足球英文专业术语
足球英文专业术语 first half 上半场 internal中场休息 second half 下半场 allowance 补时 extra time 加时 choice of ends and the kick-off are decided by the toss of a coin掷币挑边和开球kick off 开球 kick-off-time开赛时间 close game with long forward passes长传急攻 short pass短传 combination passed短传配合 double pass二过一 drive down the side-lines before centering the ball沉底传中 pass-and receive combinations传接配合 center传中 cross pass横传 one-touch pass一脚球 ground pass地面传球 scissors kick倒钩球 lofted ball高吊球 head ball顶球 ferocious tackle拼抢 block堵截 support策应 side tackle侧面抢截 dash forward插上 excessive dribbling盘带过多 pincers movement两翼包抄 playmaker进攻组织者 outflank边路进攻 fast break快攻 volley shot凌空射门 man-for-man marking盯人防守 fill gap 补位 balancing defense防守补位 “blanket” defense 密集防守 off side越位 trip opponent绊人 charge opponet 冲撞 charge opponent from behind背后铲人 fair charge合理冲撞 send off the field of play将球员驱逐出场 tackl铲球
模具方面的中英文对照
模具方面的中英文对照【二】 2007-05-09 22:35 塑料成型模具的主要设计要素 脱模距 stripper distance 脱模斜度 draft 投影面积 projected area 最大开距 maximum daylight; open daylight 闭合高度 mould-shut height 抽芯距 core-pulling distance 抽芯力 core-pulling force 脱模力 ejector force 开模力 mould opening force 模内压力 internal mould pressure; cavity pressure 成型压力 moulding pressure 背压环 back-up ring 1 bar = 14.5psi 高压接头 bite type fitting 液压马达 hydraulic motor 冷却水流量计 waterflow regulator 打磨器材 abrasive material 打磨砂轮 grinding wheels 切割砂轮 cutting wheels 码模夹(注塑机使用) mould clamps; lifting clamps 小五金工具 piping tools 高压力软管 high pressure hose 风管,水软管 air .water hose 高压油表 pressure gauge 压力油喉 hydraulic hoses 光塑检测 photoelastic testing 吹塑模 plastic blow mould 注塑模 plastic injection mould 冲扎复合模 blank & form compound die 精密冲模 precision blanking die 熔料流动率 MFR=melt flow rate 熔料流动指数 MET=melt flow index 推板导柱 guide pin for ejector plater 座板 clamping plate 垫块 space block(plate) 推板 ejector block(plate) afdek plate 档尘板 guide stripe 行位后板 cavity sub-insert 前模镶件 core sub-insert 后模镶件 sprue puller insert 扣针镶件
常用模具零件中英文对照表
常用模具零件中英文对照表 2005-12-19 14:51:17中国注塑网 一、入水:gate 进入位:gate location 水口形式:gate type 大水口:edge gate 细水口:pin-point gate 水口大小:gate size 转水口:switching runner/gate 唧嘴口径:sprue diameter 二、流道: runner 热流道:hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形流道:round(full/half runner 流道电脑分析:mold flow analysis 流道平衡:runner balance 热嘴:hot sprue 热流道板:hot manifold 发热管:cartridge heater 探针: thermocouples 插头:connector plug 插座:connector socket 密封/封料:seal 三、运水:water line 喉塞:line lpug 喉管:tube 塑胶管:plastic tube 快速接头:jiffy quick connector plug/socker 四、模具零件:mold components 三板模:3-plate mold 二板模:2-plate mold 边钉/导边:leader pin/guide pin 边司/导套:bushing/guide bushing 中托司:shoulder guide bushing 中托边:guide pin 顶针板:ejector retainner plate 托板:support plate 螺丝:screw 管钉:dowel pin
足球术语中英文对照资料
足球术语中英文对照资料 Play the goal / in goal 中坚力量: pillars of the team 补射close in/ rack up 欧洲杯:UEFA Euro 2008 2008 UEFA European Football Championship 欧洲冠军联赛UEFA Champions' Leagu--e-- 出局Greece crashed out of Euro 2008 after a 1-0 defeat by Russia 东道主直接晋级(Austria and Switzerland )automatically qualified as hosts Others are determ ined through qualify ing matches资格赛 Beckham is warming up preparing to come on pitch 热身 lightening quick 闪电般的速度 Strike rate 进球率 Keep his temperament 控制情绪 Must-win game 必赢的比赛 Punch of the corner flag 甩角旗 Putting on England shirt 穿上英格兰的战袍 Keep a clea n sheet ( no goals were scorec未丢球 Form and fitness 状态和健康 Play the first team 在一线队 Have sth under your belt: to have already achieved or obtained sth he already has a couple of trophies un der his belt将奖杯收入囊中It 's all over for Owen/ is this the end of O-Rwoeonney
西餐菜单中英文对照
西餐菜单中英文对照表大全 菠菜汤Spinach Soup烩牛肉Beef Goulash炒土豆Fried Potato 酸辣汤Hot &Sour Soup咖喱海鲜汤Seafood Curry Soup香煎茄子Pan Fried Eggplant 俄式烩牛肉Stronganoff Beef Goulash维也纳香肠Wienner Sauages 黑椒牛排Beef Steak with Black Pepper Suuce 墨西哥鸡肉饼Mexican Quesadillas 炸鸡腿Deep Fried Chicken wings 酿焰猪排Stuffed Pork Chop 金枪鱼意大利面Spaghetti with Tuna 墨西哥牛肉丸子汤Mexican Beef Ball Soup蔬菜炒饭Fried Rice with Vegetable 螺旋面Fussili Pasta 西兰花Broccoli香草西红柿汤Tomato Basil Soup 西红柿角Tomato wages米兰式西兰花Fried Broccoli奶油南瓜汤Pumpkin Cream Soup 蓝芝士菠菜汤Spinach Soup with Blue Cheese 米兰式猪排Pork Milannaise 煎土豆Roasted Potato 蘑菇鸡排Pan Fried Chicken with Mushroom香酪猪排Pork Cordon bleu香酪鸡排Chicken Corden Bleu 洋葱圈Onion Rings 奶油烩猪柳Pork Ragout 培根牛肉串Bacon and Beef Skewer 印尼炒饭Nasi Goreng 黑椒牛柳粒Sauted Beef Tenderloin with Black Pepper 奶油烩鸡Chicken Ragoat 扬州炒饭Fried Rice of Yangzhou Style 红烧牛腩Beef Stew 地中海茄子汤Mediterranean Eggplant Soup 蘑菇猪排Pan Fried Pork Steak with Mushroom with Mushroom 香辣猪肉丝Sauted Pork Slice of Sichuan Style 地中海青椒汤Mediterranean Bell Pepper Soup 奶油西兰花汤Broccoli Cream Soup 土豆泥Mashed Potato 蜜汁胡萝卜Fried Carrot
塑胶模具类中英文对照专业术语
塑胶模具类中英文对照专业术语工程部/ Design department: 1) Designer - 设计师。 2) Assembly drawing - 模具组装图。 3) Mold layout - 模具结构图。 4) 2D product drawing - 2D产品图。 5) 3D product data - 3D产品数据。 6) Part drawing - 散件图。 7) Insert molding - 镶件模。 8) 2 color mold / Double injection tool - 双色模。 9) Hydraulic system - 油/水压系统。 10) Parting line - 分模线。 11) Air venting - 排气槽。 12) Cooling system - 冷却系统。 13) Screw - 镙丝。 14) Hot runner system - 热流道。 15) Valve gate - 伐针入水口。 16) Fan gate - 扇型入水口。 17) Pin point gate - 针点进胶。 18) Moon gate / Banana gate - 香蕉,象牙入水口。 19) Submarine gate - 潜水口。 20) Injection machine tonnage - 注塑机吨数。 21) Number of cavity - 穴数。 22) Steel - 钢材。 23) Copper - 铜。 24) Tungsten copper - 钨铜。 25) Beryllium copper - 铍铜。 26) Hardening - 加硬/淬火。 27) Tempering - 回火。
模具DFM常用中英文对照
DFM常用中英文对照 1、这个红色面在前模方向/后模方向/行位方向有倒扣。 This red surface is undercut at cavity side / core side / slider side. 2、这些红色面在前模方向/后模方向/行位方向有倒扣。 These red surfaces are undercut at cavity side / core side / slider side. 3、产品的这个位置太小,导致模具在前模方向/后模方向/行位方向有薄钢位。 This position is too small and it will bring the thin steel at cavity side / core side / slider side. 4、这些红色线是前后模/镶件/行位/斜顶分型线。 These red lines are the parting line of cavity and core / insert / slider / lifter. 5、此产品使用推板/推块顶出。 Use the stripper plate / ejector block to eject this part. 6、前模/后模斜内行位。 Inner angle slider at cavity / core side. 7、为了简化模具结构建议改变此处出模方向。 Suggest to change the draft direction of this position to make the mold structure simply. 8、最终的进胶位置根据模流分析。 Finally gate position according the mold flow analysis. 9、斜顶与后面的柱位空间太小,斜顶在运动时会干涉到柱子,请考虑移动这个柱子的位置。 This lifter intervene with the pole during ejection, please consider changing the position of the pole. 10、此处有薄钢位,强度不足而且不容易冷却。 The strength of this area is too weak and it is hard to cool because the thin steel. 11、此处有尖角,填充困难。 It is hard to fill for this area because the sharp feature. 12、此处料位太厚,会有缩水,建议减胶改善。 We suggest to reduce some wall thickness to avoid the sink mark for this position. 13、此处的行位夹线在外观面上,请确认是否接受? Please confirm whether it is acceptable to have a slider line on the visible surface? 14、建议加大拔模角,以便脱模顺利。 We suggest to enlarge the draft angle to help release the tool. 15、如果分型面此处,模具上会有尖角和刀口,对模具寿命有影响。 There are sharp edges if we set the parting line here, it will reduce the tool life. 16、此处料厚段差很大,成品表面会有应力痕,建议修改如图示。 The thickness is not equal and it will bring the stress lines on the surface, suggest to improve the part as the picture shown. 17、此大行位上有小行位,开模时小行位需先退,大行位做延时,合模时则相反。 The small slider is inside the big slider, when the mold open, the small slider need to recede first and the big slider have to postpone. When the mold close, it is contrary. 18、此处需做强顶。 This position need to force ejection. 19、由于此处没有足够空间下热咀,所以需做一个柱子进胶。 This position need to make a pole for gating because there have no enough space for hot sprue. 20、沾模, stick
足球术语中英对照
足球术语中英对照 场地名称篇 field / pitch 足球场 midfield 中场 backfield 后场 kickoff circle / center circle 中圈halfway line 中线 touchline / sideline 边线 goal line 球门线 end line 底线 penalty mark (点球)罚球点 penalty area 禁区(罚球区) goal area 小禁区(球门区) 球队称谓篇 coach 教练 head coach 主教练 football player 足球运动员 referee 裁判 lineman 巡边员 captain / leader 队长 forward / striker 前锋 midfielder 前卫 left midfielder 左前卫 right midfielder 右前卫 attacking midfielder 攻击型前卫(前腰)defending midfielder 防守型前卫(后腰)center forward 中锋 full back 后卫 center back 中后卫 left back 左后卫 right back 右后卫 sweeper 清道夫,拖后中卫 goalkeeper / goalie 守门员 cheer team 拉拉队 足球技术篇 kick-off 开球 bicycle kick / overhead kick 倒钩球chest-high ball 半高球 corner ball / corner 角球 goal kick 球门球 handball 手球 header 头球 penalty kick 点球 place kick 定位球 own goal 乌龙球 hat-trick 帽子戏法free kick 任意球 direct free kick 直接任意球indirect free kick 间接任意球stopping 停球 chesting 胸部停球pass 传球 short pass 短传 long pass 长传 cross pass 横传 spot pass 球传到位 consecutive passes 连续传球 take a pass 接球 triangular pass 三角传球 flank pass 边线传球 lobbing pass 高吊传球 volley pass 凌空传球 slide tackle 铲球 rolling pass / ground pass 地滚球flying header 跳起顶球 clearance kick 解围 shoot 射门 close-range shot 近射 long shot 远射 offside 越位 throw-in 掷界外球 block tackle 正面抢截 body check 阻挡 fair charge 合理冲撞 diving header 鱼跃顶球 dribbling 盘球,带球 clean catching (守门员)接高球finger-tip save (守门员)托救球offside 越位 deceptive movement 假动作 break through 突破 kick-out 踢出界 足球战术篇 set the pace 掌握进攻节奏 ward off an assault 击退一次攻势break up an attack 破坏一次攻势disorganize the defence 搅乱防守total football 全攻全守足球战术open football 拉开的足球战术 off-side trap 越位战术 wing play 边锋战术 time wasting tactics 拖延战术 4-3-3 formation 433阵型 4-4-2 formation 442阵型 beat the offside trap 反越位成功foul 犯规 technical foul 技术犯规
足球英语
足球英文专业术语--To Start a Conversation来源:刘博垠的日志 搞懂这些基本上英文解说就能听懂了,对听其他比赛也有帮助,很多都是通用的 first half 上半场 internal中场休息 second half 下半场 allowance 补时 extra time 加时 choice of ends and the kick-off are decided by the toss of a coin掷币挑边和开球kick off 开球 kick-off-time开赛时间 close game with long forward passes长传急攻 short pass短传 combination passed短传配合 double pass二过一 drive down the side-lines before centering the ball沉底传中 pass-and receive combinations传接配合 center传中 cross pass横传 one-touch pass一脚球 ground pass地面传球 scissors kick倒钩球 lofted ball高吊球 head ball顶球 ferocious tackle拼抢 block堵截 support策应 side tackle侧面抢截 dash forward插上 excessive dribbling盘带过多 pincers movement两翼包抄 playmaker进攻组织者 outflank边路进攻 fast break快攻 volley shot凌空射门 man-for-man marking盯人防守 fill gap 补位 balancing defense防守补位 “blanket” defense 密集防守 off side越位 trip opponent绊人 charge opponet 冲撞
模具中英文对照表
landed plunger mold 有肩柱塞式模具burnishing die 挤光模 landed positive mold 有肩全压式模具button die 镶入式圆形凹模 loading shoe mold 料套式模具 center-gated mold 中心浇口式模具loose detail mold 活零件模具 chill mold 冷硬用铸模 loose mold 活动式模具 clod hobbing 冷挤压制模 louvering die 百叶窗冲切模composite dies 复合模具 manifold die 分歧管模具 counter punch 反凸模 modular mold 组合式模具 double stack mold 双层模具 multi-cavity mold 多模穴模具electroformed mold 电铸成形模 multi-gate mold 复式浇口模具expander die 扩径模 offswt bending die 双折冷弯模具extrusion die 挤出模
palletizing die 叠层模 family mold 反套制品模具 plaster mold 石膏模 blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具 fantail die 扇尾形模具 pressure die 压紧模 fishtail die 鱼尾形模具 profile die 轮廓模 flash mold 溢料式模具progressive die 顺序模 gypsum mold 石膏铸模 protable mold 手提式模具 hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模 punching die 落料模 lancing die 切口模 raising(embossing) 压花起伏成形re-entrant mold 倒角式模具
足球术语英语翻译大全.docx
场地名称篇 field / pitch 足球场 midfield 中场 backfield 后场 kickoff circle / center circle 中圈halfway line 中线 touchline / sideline 边线 goal line 球门线 end line/goal line/ post line 底线penalty mark (点球)罚球点 penalty area 禁区(罚球区) goal area 小禁区(球门区) flank/ wing 辅位 woodwork 球门框 crossbar/ bar 门楣 goalpost/ post - 门柱 球队称谓篇 coach 教练 head coach 主教练 football player 足球运动员 referee 裁判 lineman 巡边员 captain / leader 队长 forward / striker 前锋 midfielder 前卫 left midfielder 左前卫 right midfielder 右前卫 attacking midfielder 攻击型前卫(前腰)defending midfielder 防守型前卫(后腰)center forward 中锋 full back 后卫 center back 中后卫 left back 左后卫 right back 右后卫 sweeper 清道夫,拖后中卫goalkeeper / goalie 守门员 cheer team 拉拉队 substitute/ reserve 替补 journalist 记者 ball picker 拾球童 crowd/ fans 球迷
欧洲五大联赛队名中英文对照
欧洲五大联赛队名中英文对照 意大利足球甲级联赛Italy Seria A 亚特兰大Atalanta 博洛尼亚Bolonga 佛罗伦萨Firoloutina 国际米兰Intermilan 尤文图斯Juventus 莱切Lecce AC米兰https://www.360docs.net/doc/853641344.html,an 佩鲁贾Perugia 罗马Roma 维罗纳Verona 切维沃Chievo 威尼斯Venice 都灵Turin
皮亚琴察Piacenzaca 英格兰超级联赛England Premiership 阿森纳Arsenal 阿斯顿维拉Aston Villa 查尔顿Charlton 切尔西Chelsea 德比郡Derby 埃弗顿Everton 伊普斯维奇Ipswich 利兹联Leeds 莱切斯特Leicester 利物浦Liverpool 曼联Man Utd 米德尔斯堡Middlesbrough 纽卡斯尔Newcastle
桑德兰Sunderland 南安普顿Southampton 托特纳姆Tottenham 西汉姆West Ham 富尔汉姆Fulham 布莱克本Blackburn R. 博尔顿Bolton W. 德国足球甲级联赛Germany Bundesliga 慕尼黑1860 Munich 1860 拜仁慕尼黑Bayern Munich 云达不莱梅Werder Bremen 科特布斯Energie Cottbus 多特蒙德Borussia Dortmund 弗雷堡SC Freiburg 柏林赫塔Hertha BSC
汉堡Hamburger SV 凯泽斯劳滕Kaiserslautern 科隆Cologne 勒沃库森Bayer Leverkusen 罗斯托克Hansa Rostock 沙尔克04 Schalke 04 沃尔夫斯堡VfL Wolfsburg 斯图加特VfB Stuttgart 纽伦堡Nurnberg 圣保利St.Pauli 门兴格拉德巴赫Monchengladbach 西班牙甲级联赛Spain La Liga 阿拉维斯Alaves 奥萨苏纳Osasuna 巴列卡诺Rayo Vallecano
模具常用术语中英文对照表
"R,L Co.,Ltd" 模具常用术语中英文对照 模芯Parting Core 局部视图Partial View 冷料# Cold Slag 线切割 Wire 轮廊Contour 螺纹孔 Tapping Hole 连接件 Fittings 斜针Angle Pin 接合Engage 替换镶件Interchangeable Mold Inserts 指定吨位的注塑机Specific Press 水嘴接头Water Fittings 螺纹Eyebolt Thread 回针Stop Pin 二级顶出针Sub-Leaderd Pin 镶件Mold Insert 加硬Harden 唧嘴Sprue 设计筒图Design Preliminary 名称块表Title Block 版本标识Revision Level 材料清单Stock List 制模Build Mold 手动滑块Hand Slide 漏水测试Leak Test 流道排气Runner Vents 抛光Draw Polish 侧抽芯 Side Action 加强筋 Reinforcing
三角撑 Gusset 柱子Bossed 出模斜度Draft 外廊Contour 落单会议Kick-Off Meeting 装卸孔 Handling Hole 运输安全带Moldstrap 码模槽 Clamp Slot 撑头Support Pillar 螺牙1/2-13 Eye Bolt 1/2-13Tap 导柱位 Leader Pin Location 耐落胶 Teflon Paste 偏移量 Offset 水塞Water Line Plug 撬模脚 Ppy Slot 重新加工Reworked 配件Components 补偿Compensation 平面度 Parallel 倒角Chamfer 模胚Mold Base 热嘴Hotnozzle 火花机 Edm 熔接线 Weildline 压机Press 晒纹Texturing 梯形Trapezoid 凸缘、法兰Flange 方铁Spacer Block 顶针板Ejector Plate 顶针底板Ejector Retainer Plate 垫板Retainer Plate
足球术语(中英韩对照)
足球术语(中英韩对照) 1.??????(advantage rule,攻方有利原则) : ????????????? ?????????????????????????????????????? 2.??(attack,进攻) : ?? 3.???(attacker,攻击手) : ??? 4.???(back heeling,脚后跟踢球) : ???????? 5.???(back pass,回传) : ?????????????? 6.????(ball control,控球) : ???? 7.??(????) (block(intercept),抢断球) : ??,?? 8.?????(body contact,身体接触) : ???? 9.??(bully,混战) : ???????????????????? 10.??(caution,注意、警告) : ?? 11.????(center circle,中圈) : ??? 12.???(centering,传中) : ????????????????? 13.?????(center forward,中锋) : ????? 14.?????(center half-back,中后卫) : ????? 15.????(center line,中线) : ??? 16.??????(changing position,交换位置) : ?????????????? ? 17.??(charging,撞人犯规) : ??????????? 18.??(chip kick,过顶球) : ?????????????????????? ? 19.???(clear,大脚解围) : ?????????????????????? ???? 20.??(corner,底线和边线交叉处(角球)) : ?????????????? ?? 21.????(corner flag,角球旗) : ?????? 22.???(corner kick,角球) : ???????????????????? ????????????????????? 23.???????(corner kick area,角球区) : ????????? 24.????(cross-bar,横梁) : ????(门柱)??????????? 25.????????(dangerous play,危险动作) : ??????
足球英语专业术语
足球英语专业术语 搞懂这些基本上英文解说就能听懂了,对听其他比赛也有帮助,很多都是通用的 first half?? 上半场 internal中场休息 second half 下半场 allowance 补时 extra time 加时 choice of ends and the kick-off are decided by the toss of a coin掷币挑边和开球 kick off 开球 kick-off-time开赛时间 close game with long forward passes长传急攻 short pass短传 combination passed短传配合 double pass二过一 drive down the side-lines before centering the ball沉底传中 pass-and receive combinations传接配合 center传中 cross pass横传 one-touch pass一脚球 ground pass地面传球 scissors kick倒钩球 lofted ball高吊球 head ball顶球 ferocious tackle拼抢 block堵截 support策应 side tackle侧面抢截 dash forward插上 excessive dribbling盘带过多 pincers movement两翼包抄 playmaker进攻组织者 outflank边路进攻 fast break快攻 volley shot凌空射门 man-for-man marking盯人防守 fill gap 补位 balancing defense防守补位 “blanket” defense 密集防守 off side越位 trip opponent绊人 charge opponent 冲撞
模具DFM常用中英文对照
DFM常用中英文对照 15、如果分型面此处,模具上会有尖角和刀口,对模具寿命有影响。. There are sharp edges if we set the parting line here, it will reduce the tool life. 16、此处料厚段差很大,成品表面会有应力痕,建议修改如图示。. The thickness is not equal and it will bring the stress lines on the surface, suggest to improve the part as the picture shown. 17、此大行位上有小行位,开模时小行位需先退,大行位做延时,合模时则相反。. The small slider is inside the big slider, when the mold open, the small slider need to recede first and the big slider have to postpone. When the mold close, it is contrary. 18、此处需做强顶。. This position need to force ejection. 19、由于此处没有足够空间下热咀,所以需做一个柱子进胶。. This position need to make a pole for gating because there have no enough space for hot sprue. 20、沾模, Stick 1.High shrinkage values could indicate sink marks or voids at gate location 高缩水率的产品容易产生缩印,但在浇口附近可以避 免。. 2.Welding line on the cosmetic surface 熔接线在外表面 3.Two banana gate was to being confluent in the end of melt flow. 两个香蕉浇口在流动未端熔合。. 4.Venting insert here has flash 排气镶件处有飞边 5.Venting gap between inserts is too big 镶件处的排气槽过大 6.Stress mark on the cosmetic surface 产品外表面上有压痕 7.Uneven thickness 不平均的产品壁厚 8.Unreasonable product structure 不合理的产品结构 9.Injection speed is high 注塑压力过高 10.There is black spot on the cosmetic surface 产品外表面上有黑色点 11.There is flash on the product 产品有飞边 12.there is sink mark on the cosmetic surface 产品外表面上有缩痕 13.Gate size is not reasonably 浇口尺寸不合理 14.There is argent spot 这里有亮点(银色斑点) 15.The plastic of first shot didn't meet high temperature. 塑料的第一胶不会有很高的温度。. 16.Make sure the core float plate was closed before lifter completely return to correct position 确认lifter完全回位时core侧 浮动板已经复位 17.Make sure the ejector system is smooth 确认顶针系统移动平稳 18.Add early return structure to protect lifter return to correct position 增加先复位机构保护lifter回到正确位置。. 19.Propose to add draft on slider side wall and draw polish. 建议增加slider的角度和抛光角度。. 20.It is too thin and very difficult to inject fully, and weakness wall will have risk of the part function 该处壁厚过薄而造成很难去 填充完整,薄壁将会有产品功能上的风险。. 21.These are will have sink marks due to uneven thickness, propose to reduce plastic. 壁厚不均匀容易产生缩印,建议在该处减胶。. 22.These are will have sink marks due to ribs opposite. 正面的筋位易导致背面产生缩印。. 23.Please confirm the 3D part thickness whether has including painting thickness or not? 请确认产品的设计是否考虑到油漆的厚 度。.
模具--中英文对照
dowel pin 定位梢 draft 拔模锥度 draw bead 张力调整杆 drive bearing 传动轴承 ejection pad 顶出衬垫 ejector 脱模器 ejector guide pin 顶出导梢 ejector leader busher 顶出导梢衬套ejector pad 顶出垫 ejector pin 顶出梢 ejector plate 顶出板 ejector rod 顶出杆 ejector sleeve 顶出衬套 ejector valve 顶出阀 eye bolt 环首螺栓 filling core 椿入蕊 film gate 薄膜形浇口 finger pin 指形梢 finish machined plate 角形模板 finish machined round plate 圆形模板fixed bolster plate 固定侧模板flanged pin 带凸缘销 flash gate 毛边形浇口 flask 上箱 floating punch 浮动冲头 gate 浇口 gate land 浇口面 gib 凹形拉紧楔 goose neck 鹅颈管
guide bushing 引导衬套 guide pin 导梢 guide post 引导柱 guide plate 导板 guide rail 导轨 head punch 顶头冲孔 headless punch 直柄冲头 heavily tapered solid 整体模蕊盒hose nippler 管接头 impact damper 缓冲器 injection ram 压射柱塞 inlay busher 嵌入衬套 inner plunger 内柱塞 inner punch 内冲头 insert 嵌件 insert pin 嵌件梢 king pin 转向梢 king pin bush 主梢 一、入水:gate 进入位:gate location 水口形式:gate type 大水口:edge gate 细水口: pin-point gate 水口大小:gate size 转水口:switching runner/gate 唧嘴口径:sprue diameter 二、流道: runner 热流道:hot runner, hot manifold 热嘴冷流道: hot sprue/cold runner