bigsky 说明书英文版

USER MANUAL

Front Panel Controls

VALUE: Turn for fi ne adjustment of Decay time when time is displayed. Scrolls through presets when bank or name is displayed. Push to access the PARAMETER menu, hold to access the GLOBAL menu. DECAY: Controls the Decay time of the reverberated signal. The range can depend on the selected reverb machine.

PRE-DELAY: Adjusts the time between the dry signal and the onset of the reverb, from 0 to 1.5 seconds. For the Nonlinear and Magneto machines, this knob controls the amount of Feedback.

TONE: Adjusts the high end content of the reverb. Lower settings create darker, warmer

reverberation, higher settings are bright and crisp. Set at 12:00 for a nicely balanced top end.

MOD: Adds

modulation to the reverberated signal. Lower settings modulate the delay lines lightly for a subtle and natural movement, higher settings tastefully add stronger modulation.

PARAM 1 & 2: Assignable to parameters for the current reverb machine. To assign, choose the desired parameter, press and hold value encoder while turning a PARAM knob.

TYPE: Turn to select desired reverb machine. Push to toggle the display to show Decay time or the current bank. Hold to save current preset.

A, B, & C LEDS: Green if active. Amber if the preset has been edited. Off if bypassed.

MIDI: Full featured MIDI input and output supporting CCs, Program changes, etc. See MIDI Specifi cation section.INPUTS: High impedance inputs. Use LEFT input for mono.

OUTPUTS: Use LEFT output for mono.

CAB FILTER SWITCH: Set switch to ON for a sophisticated speaker

response curve. See Cab Filter .

EXP: Connect an

expression pedal. See EXP Connections

Rear Panel

The displayed Decay time is the Tr60 value, which is the time it takes for the reverberated signal to decay to -60dB (1/1000th) of its initial value.Hall, Plate, Swell, Bloom, Chorale, Shimmer 500mS — +20.00S

800mS — 10.00S 1.00S — +50.00S 200mS — 1.50mS Nonlinear 50mS — 2.00S Re? ections 133mS — 400mS to toggle the display between BANK, NAME & TIME

push the TYPE encoder

In Depth: PARAM 1 & 2 controls

. Turn either the PARAM 1 or PARAM 2 knob to assign a parameter .

Turn the newly assigned PARAM knob to adjust your reverb machine parameter .

The PARAM 1 & PARAM 2 knobs allow you quick access to any desired menu parameter of the currently active reverb machine. For example, DIFUSN on the Cloud machine can be assigned to one of the parameter knobs to allow for easier control over the reverb diffusion.

Press and hold the value encoder .

EXP Connections

Connect an external TAP switch for remote control of Pre-Delay (or Decay time with the Magneto and Nonlinear machines). Use a standard TRS cable to connect the external switch. Set the EXP MD global setting to TAP to use external tap.

Connect a Strymon

MultiSwitch for external tap, bank, or preset

selection. Set the EXP MD global setting to either TAP, BANK, or PRESET.

Please refer to the

MultiSwitch user manual for detailed setup information: https://www.360docs.net/doc/a28869497.html,/support/multiswitch

Connect a standard TRS expression pedal for continuous control over any knob. To select the knob(s) controlled by the expression pedal, use the EP SET parameter in each preset. All

knobs can be controlled simultaneously. See

Common Parameters for set up instructions.

Banks and Presets

BigSky has 100 banks with A, B, and C presets in each bank. Banks are numbered 00 to 99 on the display.

Note: BigSky ships from the factory with the fi rst 100 presets (00A-33A) duplicated from 33B-66B, and again from 66C-99C.

POWER UP BigSky while holding A & C.

Keep holding for 5 seconds after BigSky has powered up.

REINIT will be displayed and all factory presets will automatically be restored

Save a preset to a new location:

To cancel an in-progress save press the VALUE encoder hold the TYPE encoder

hold the TYPE encoder

the TYPE encoder save your settings

turn the VALUE encoder

to select the bank to

save to

push the TYPE encoder or the A, B, or C footswitch to save your settings

Reverb Machines: Common Parameters

Reverb Machines share a set of parameters. These parameters are saved with each preset and include:+/- 3dB of boost/cut. This can be useful for level matching in your effects chain, or can be Persist :

Hold :

Name : Expression Pedal ON/OFF Expression Pedal Set: While displaying BANK,

NAME or TIME

push the VALUE encoder

to enter PARAMS

turn the VALUE encoder

to select the desired PARAMETER

push the VALUE encoder

and turn to edit the selected PARAMETER

A versatile room algorithm that creates environments ranging from well-tuned studio ambience to larger night club

acoustics. The Tone knob, Diffusion and Low End parameters adjust the damping and scattering effects of room materials, STUDIO Size:

Diffusion:

CLUB

TIPS & TRICKS:

For realistic acoustic spaces, Pre-Delay can be kept at minimum, with Decay values in the 500mS to 2

second range. However, the Room algorithm is designed to be just as adept at long decay times. For great atmospheric reverbs, try Pre-Delay at noon, Decay at 12 seconds or more, and Mod at 1:00. Mix to taste.The Mod control randomly modulates the reverb’s delay lengths for the fi rst half of the knob travel for subtle natural movement, and then adds modulation to the input of the reverb tank for the 2nd half of the knob travel for a more overt yet tasteful modulation experience.

+ | | -

ections and slower-building density are the hallmarks of this beautiful and versatile reverb. The Concert size is well-balanced, spacious and warm, while the Arena size is huge, enveloping and booming. The Mid parameter allows for precise EQ tailoring of the reverberated sound.- | +

- | +

CONCERT ARENA

Mid:

Size :

TIPS & TRICKS:

Adding some Pre-Delay can increase the sense of physical space and further separate the reverb from the dry signal. For a balanced, versatile hall sound that will be complement just about any input source and style, try Concert with

a decay of about 3.5 seconds, with the Tone at noon and Lo End parameter centered. Setting the Mod kno

b at 12:00 maximizes the random delay-length modulation, further increasing the warmth.

For realistic mega-structure reverb, choose Arena with a 10 second decay or longer and increase the Lo End parameter . Keep the Mix control below 12:00.

The Mod control randomly modulates the reverb’s delay lengths for the fi rst half of the knob travel for subtle natural movement, and then adds modulation to the input of the reverb tank for the 2nd half of the knob travel for a more overt yet beautifully tasteful modulation experience.

- | +

The Plate machine is a rich, fast-building reverb that creates depth without early refl The Tone knob and Low End parameter are simple but powerful frequency shaping tools.SMALL LARGE

Size :

TIPS & TRICKS:

The undamped Decay time of traditional large plate reverbs is about 5 seconds. Large baffl es were positioned close to the plate to damp the vibrations for shorter reverbs as required. Try short decays around 1.5s with lower Mix values to add some subtle ambience to dry tracks. Long decay times can go beyond physical limitations to create clear ambient pads of reverb.

Plate reverbs were routinely run through a post EQ to tailor the low end to sit properly in the mix, and to reduce less pleasant high frequency ringing. The Low End parameter’s wide range is voiced for maximum fl exibility, while the Tone knob adjusts the high end from unfi ltered full-bandwidth (max) to warm (noon) to dark and damped (min).

The Large plate’s traditional size yields lush, smooth and transparent reverb that adds a bit of class to any track or instrument. The Small plate’s size dictates a splashier, ringy characteristic with less low end effi ciency - perfect for applications that call for something a bit less sophisticated.

The Mod control modulates the reverb’s delay lengths with a special LFO that allows for lush modulation without warble.

The standalone spring tank became a staple of surf and spaghetti-western music that developed in the ‘60s. The Spring machine allows for complete customization from warm and mellow to splashy and dripping with its Tone and Mix Controls, Dwell parameter, and selectable number of springs.

- | +

Dwell:

CLEAN

COMBO

TUBE

OVERDRIVE

TIPS & TRICKS:

For traditional combo amp tones, use the 2-spring option with the Combo Dwell setting and decays of around

4.5 seconds.. Many combo amps have a darker spring tone, so try rolling the Tone knob back to mellow out

the reverb. Try lower settings on the Low End parameter to reduce the low frequency content as well.

For more sophisticated spring reverbs, try the 3-spring reverb with Clean Dwell settings and shorter decay

times, around 3 seconds. Keep the Low End parameter at the half-way point and adjust the Tone knob to

taste.

For maximum splash, crank the Tone knob to maximum and turn the Low End param to minimum. Turn up

the Mix to 3:00 if you’re bold.

Hot input signals will drive the spring harder. Reduce the Dwell setting if you experience too much spring

distortion.

Most spring circuits attenuate the low end pretty heavily to avoid rumble and feedback issues. This represents

The Swell machine brings in the reverb gradually behind the dry signal for subtle evolving textures, like having a volume pedal on the wet signal. Alternatively, you can choose to have the dry signal swelled into the reverb, for maximum ambience Rise Time :

Mode :

Chooses the confi guration of the Swell machine. The Swell Wet option swells in the wet signal behind your dry signal for a subtle evolving verb. The Swell Dry mode swells the dry signal in front of the reverb for awesome ambience or swelled solos.

SWLWET SWLDRY

TIPS & TRICKS:

For a volume-knob effect for soloing, use the Swell Dry mode with a Rise time of 0.3 seconds or less.

For long ambient chords, try the Swell Dry mode with Rise Time greater than 1 second, decay times longer than 10 seconds, with high modulation settings.Try using the Swell Wet mode with a short Rise Time, around 0.10 seconds, for a reverb that sits nicely behind the dry signal.

The Mod knob adds 4-phase modulation of the reverb’s delay lines, lending a sense of movement and depth to the reverb signal.

0.08 0.100.120.140.170.20

0.250.300.350.400.50

0.600.700.800.901.00

1.201.401.70

2.002.50

3.00

4.00

- | +

In the ‘90s, more diffusion blocks were added to reverbs to smooth out the sound. A side effect of this was the tendency of the reverbs to have a slowly building envelope that ‘bloomed’, resulting in big ambient reverbs that sit nicely with the dry signal - | +

|||||||||

Length:

Feedback: TIPS & TRICKS:

The Decay knob controls the tank’s decay time, while the Length parameter controls the bloom length. High settings of the Length parameter and/or higher Feedback settings can result in reverbs that are much longer than the displayed tank decay time.

Experiment with short Decay times and higher Length values, and then longer Decay times with lower length values to get a feel for how these two portions of the reverb interact and complement each other .The Mod knob controls two independent 16-phase oscillators for a total of 32 oscillator signals. The fi rst 16-phase oscillator modulates the bloom-generating delay lines, while the 2nd 16-phase oscillator modulates the tank reverb delay lines. The result is sublime, big, and beautiful.

The Tone knob is a unique resonant fi lter that shapes the top end with synth-like voicing. Experiment by adjusting the Tone knob with long-decay reverbs.

High Feedback settings paired with high Modulation results in a gorgeous spectrum of sweeping resonant harmonics.

A gorgeously big, ambient reverb that draws from techniques developed in the late ‘70s. Using processing power not dreamed of in those days, the Cloud reverb machine obscures the distinction between reality and fantasy.

TIPS & TRICKS:

The cascaded input diffusion blocks create an expanded ‘early’ reverb. This results in a longer overall reverb time than the displayed tank decay time, most noticeable when the Decay knob is set to low values.

From min to 2:00, the Modulation knob adjusts the amount of modulation (developed by a quadrature oscillator at a frequency harmonious to the Cloud generator) that is applied to the input diffusor sections. Past 2:00, the frequency of the quadrature oscillators is increased.

The modulation scheme was developed to allow for high degrees of modulation without muddying up the sustaining reverberation tail.

The Cloud reverb can take any modest guitar or synth sound and turn it into a gorgeous ensemble.

- | +

Diffusion :

A vocal choir accompanies your music. Choose vowel ranges and intensities to customize your choir as it sings in venues that vary with the Decay knob. As the Modulation is increased, the choir becomes alive with multitude of voices. AAHHOO MILD AAHH MEDIUM AAHHOH HIGH

OOOHOH OOOO RANDOM

TIPS & TRICKS:

Adjust the Tone knob to add more ‘breath’ and high end articulation to the vocals.

The Mod knob is a very effective way to add realism to the chorale. As Mod is turned up, randomization is added to the chorale’s pitch and timbre to create an increasing number of singers that have distinct voices.

Since many of the vocal formant frequencies are ‘mid-range’ frequencies, a mid-heavy guitar amp may overly re-enforce some of them at High Reso settings. In those cases, reduce the Reso setting to Medium or Mild.

Two tunable voices add pitch-shifted tones to the reverberated signal, for resplendent, unearthly ambience. The voices are carefully created from the reverberated signal itself to generate maximum radiance and beauty. The Amount and Mode parameters allow for a range of shimmer effects from laid-back and subtle to full-blown majestic splendor

Amount: Adjusts the level of the shifted

TIPS & TRICKS:

The Amount parameter works in conjunction with the Mode

parameter to produce the particular intensity of the shimmer

effect. If Amount is set to Off, no shimmer effect is heard.

For deep octave down shifts, increase the Low End parameter

to allow the lower octave frequencies to come through

strongly.

The Modulation knob modulates the shimmer voices as

well as the reverb tank’s delay line lengths with a 4-phase

oscillator. Increasing the modulation widens the shimmer

experience and promotes a general sense of well-being.

Try +1 Oct and Oct.5th with lower amount levels for just a hint

of shimmer.

Try Oct.5th and–P5 with ‘Input’ shimmer Mode for an other-

wordly synth-pad.

-Octave

Off

-Major 7th

-minor 7th

-Major 6th

-minor 6th

-Perfect 5th

-minor 3rd

-Major 2nd

+Major 2nd

+minor 3rd

+Major 3rd

+Perfect 4th

+Tritone

+minor 7th

+Major 7th

+Octave

+Octave & 5th

+2 Octaves

Shift 2: Selects the 2nd voice interval, from an octave down to two octaves up. Can be set to Off if no

2nd voice is desired.

-Tritone

-Perfect 4th

-Major 3rd

-minor 2nd

-10 cents

+10 cents

+minor 2nd

+Perfect 5th

+minor 6th

+Major 6th

Mode:

Low End:

A new style of music emerged in the late ‘50s, featuring the guitar as the ‘lead voice’ enhanced by the reverberated wash of a multi-head echo. The Magneto machine sets up a multi-head echo with all heads on, while the PreDelay knob adds feedback. The Diffusion parameter adds a new dimension of ambience, smearing the response of the heads and blurring Number of Heads Diffusion :

Spacing :

Even spacing puts the heads at the same distance from one another for equal delay times. Uneven EVEN 3 UNEVEN

TIPS & TRICKS:

The last repeat occurs at the displayed decay time, so a 300ms decay time with 3 evenly spaced heads would have repeats at 100ms, 200ms, and 300ms. Switching to a 4-head machine results in delays at 75ms, 150ms, 225ms, and 300ms.

The age, condition, and alignment of the record and playback heads greatly infl uence on the tonality of magnetic media delays. As a result, they may bright or dark, high-passed or fuller in the low frequencies. The Tone knob and Low End parameters are wide-ranging to allow for a full spectrum of tones. As the Feedback (Pre-Delay knob) is increased, the EQ response is regenerative, leading to evolving soundscapes and ambient washes.

The Mod control acts as a Wow and Flutter generator, adding hypnotic movement and fullness to the sound.

DELAY TIME: Sets the Delay time of the last head.

FEEDBACK: Adds

feedback from the last head back to the input when Even Spacing is selected. With Uneven Spacing, the feedback is taken from the last two heads.

- | +

A variety of physics-defying reverb shapes are available for special effects and unique textures. Choose from three ‘backwards’ shapes (Swoosh, Reverse, and Ramp), or a Gate and more. Feedback control, Late Reverb, and Diffusion Shape :

Adjusts the shape of the nonlinear generator SWOOSH REVERS RAMP

GATE

GAUSS

BOUNCE

Diffusion:

Controls the effect of diffusors on the nonlinear generator Late Decay:

Adjusts the decay time of the late reverb. Higher settings produce Late Level:

Adjusts the level of the late reverb. Higher settings increase the level Mod Speed:

Adjusts the modulation LFO speeds for both the the non-linear delay TIPS & TRICKS:

The Nonlinear generator feeds into the late reverb. The Pre-Delay knob adds feedback around the nonlinear generator before it enters the late reverb portion, producing repeating nonlinear shapes as you turn the knob clockwise.

The Diffusion parameter softens the Nonlinear portion, and is useful with longer Decay times. High Diffusion levels with short decay times can result in a ‘metallic’ sound. Reduce the Diffusion parameter in these cases if desired.

Short decay times and no feedback (Pre-Delay knob minimum) with the Gate shape gives an interesting level-independent take on the traditional ‘gated reverb’.

Try high feedback levels (Pre-Delay knob) with some added Modulation to create trippy ambient textures.Maximum feedback (Pre-Delay knob maximum) with the Gate shape will produce a nearly endless wash of ‘multi-tapped’ reverb. Try Decay at 800ms and Modulation at 10:00.Try the Swoosh or Reverse shapes at very short decays (<100ms) for a great slapback effect. Try minimum Diffusion for best results.

The Mod control varies the

nonlinear generator tap lengths, as well as the late reverb’s delay lines for an expanded experience.

TIME: Sets the time of the

nonlinear portion of the reverb.

KNOB FUNCTIONS: FEEDBACK: Adds feedback

from the nonlinear portion of the - | +

- | +

|||||||||

ections machine is a psycho-acoustically accurate small-space reverb that allows you to move your amp anywhere in ections algorithm precisely calculates 250 refl ers adjust for human auditory perception to create unparalleled ambient-space realism to F | | B

+ | | -

L | | R

Location Y:

Location X:

Shape:

TIPS & TRICKS:

The Decay knob adjusts the size of the room from 100 sq ft (10’x10 square, or 8’x13’ rectangle and oblong) to 1000 sq ft (31’x31’ square, or 24’x39’ rectangle and oblong). As the room size increases, the decay increases accordingly.

Set Mix at 12:00 and Pre-Delay to 0 (minimum) for a natural room response.

Darker Tone settings would come about from carpeting, drapes and other absorptive elements on the refl ecting surfaces. Brighter Tone settings create the sound of stone or tiled walls, with fewer absorbing materials in the room.

Reduce the Low End to give a more natural room or studio environment with furnishing/couches etc. Increase Low End for more of an ‘empty space’ reverberation.

SQUARE RECT OBLONG

Global parameters affect BigSky regardless of what preset is currently active.

TRUE BYPASS True Bypass and Buffered Bypass . In .

BUFFERED BYPASS

CH 1 - 16

MIDI Channel: ON MIDI Continuous Controllers: Turns MIDI CC messaging (continuous controllers) ON or OFF.

OFF

ON MIDI Patch Change:OFF

ON MIDI Through: OFF

BNK 1-99

Bank Scroll: PEDAL EXP input mode:EXP input to use an Expression Pedal , an external TAP footswitch, or

MultiSwitch .

TAP BANK PRESET - for use with Expression Pedal

- for use with external TAP footswitch, or MultiSwitch for tap and preset select - for use with MultiSwitch to select preset banks - for use with MultiSwitch to select presets

Please refer to the MultiSwitch user manual for detailed MultiSwitch setup information: https://www.360docs.net/doc/a28869497.html,/support/multiswitch

球阀使用说明书英文版(ball valve)

Product Manual - Operation and Maintenance Manual Product Name:API 6D Ball Valve January 2012

1Scope This manual covers manually/motor/pneumatic operated seat supported /trunnion supported ball valve having tow/three pieces body with nominal sizes DN 15mm-1200mm (1/2”-48”) and class ranges PN1.6MPa-10MPa(ANS1 class 150-2500). Valve ends may be threaded, flanged, butt-welded or socket 2 Applications 2.1 Ball valves are used to open/close the flow in pipeline. 2.2 The nature of applicable fluid depends on valve material: 2.2.1 Carbon steel valve applies to non-corrosive fluid, such as water, vapor or oil etc. 2.3 Temperature range depend on sent material: PTFE ≤130℃ RPTFE ≤160℃ PPL ≤300℃ NYLON ≤121℃ 3. standard： Basic design API 6D-2008 Inspe crlon tesring BS EN 12266.1-2003 End flange ASME B16.5-2009 TEMP. & PRESSURE ASME B16.34-2009 Face toface ASME B16.10-2009 Main parts and materials ASME materials, see Table 1 Figure 1:Trunnion Ball Valve 4 Structure 4.1 Ball Valve structure is shown in Fig. 1.

阿特拉斯空压机说明书

1.1安全图标说明人身危险警告的重要注意事项1.2一般安全措施一般预防措施1.操作员必须遵守安全操作规则并遵守所有相关的工作安全要求和规定。 2.如果以下任何陈述不符合适用法规，则以更严格的陈述为准。 3.安装，操作，维护和维修工作只能由经过培训的授权专业人员执行。 4.压缩机产生的空气不被认为具有呼吸质量。为了使压缩空气达到呼吸质量，必须根据适用的法律和标准对压缩空气进行充分净化。 5.在进行任何维护，修理，调整或任何其他非常规检查之前，请先停止压缩机，按紧急停机按钮，切断电源，并给压缩机降压。此外，必须打开并锁定电源隔离开关。 6.不要玩压缩空气。请不要让空气接触您的皮肤或将气流引导至人。请勿使用压缩空气对衣服进行除尘。使用压缩空气清洁设备时，请小心并戴防护眼镜。 7.用户有责任将设备维持在安全的工作状态。如果零件和附件不适合安全操作，则应将其更换。 8.禁止在压缩机外壳的顶板上站立或行走。1.3安装时的安全注意事项。因忽视这些注意事项或不遵守安装，操作，维护和修理所需的正常警告和注意事项（即使未指定）而造成的任何损坏或伤害，制造商概不负责。安装期间的注意事项1.只能根据适用的安全法规，使用适当的设备来抬起

机器。抬起之前，必须安全固定松动的零件或旋转的零件。提起重物时，禁止将其悬吊或停留在危险区域中。提升加速度和减速度必须保持在安全范围内。在高海拔或起重设备区域工作时，必须戴好安全帽。2.将机器放置在空气尽可能凉爽和清洁的环境中。如有必要，安装吸油管。不要阻塞进气口。必须采取措施尽可能减少进气中的水分。3.在连接管道之前，必须清除所有盲板法兰，塞子，盖子和干燥剂袋。6 2991 7092 20说明手册4.空气软管的尺寸必须正确并且适合在工作压力下使用。请勿使用磨损，损坏或旧的软管。支管和连接的尺寸必须正确，并且适合在工作压力下使用。5.吸入的空气中不得包含会引起内部火灾或爆炸的可燃气体，蒸气和颗粒（例如油漆溶剂）。6.安排进气口，以防止吸入操作员穿着的宽松衣服。7.确保从压缩机到后冷却器或空气网络的排气管在加热时能自由膨胀，并且不靠近易燃物或与易燃物接触。8.不得对排气门施加外力；连接管不得扭曲或变形。9.如果安装了遥控器，则必须清楚地标记机器以指示危险：机器是远程控制的，可能会启动而不会发出警报。在进行维护或修理之前，操作员必须确保关闭机器，并且隔离开关处于打开和锁定状态。为了进一步确保安全，打开远程控

英文产品说明书

Spiral chute 1、product description Spiral chute is integrated spiral separator, spiral chute, shaker, centrifugal concentration machine characteristics of the equipment, mining, mineral processing is the best equipment, especially the seaside, riverside, sand beach, the stream of placer mining is more ideal. The product has the advantages of reasonable structure, simple installation, covers an area of small, simple operation, stable ore beneficiation, clear, large processing capacity, high efficiency enrichment ratio high, high recovery rate, reliable operation characteristics. Have weight light, moisture-proof, rust-proof, corrosion resistance, of the feeding quantity and concentration, particle size, quality of volatility adaptability is strong, no noise. 2、Separation principle Spiral chute is a membrane flow gravity separation equipment, the selection principle is the use of useful minerals and gangue in proportion, particle size, shape differences, in rotating inclined flow by gravity, centrifugal force, hydrodynamic pressure and friction force with different groove face, realize the useful minerals and gangue stratification, branch tape sorting. Heavy, coarse granularity, fast sedimentation of particles gradually moved towards the spiral groove inner edge, the proportion of small, fine particle size, particle sedimentation slow gradually moved to the spiral groove edge, gradually banding, culminating in the spiral groove end by cutting ore tank is respectively connected out, to realize separation. 3、Application The sorting equipment for grain size mm fine iron ore, titanium ore, chromite,

产品说明书英文版V完整版

产品说明书英文版V HEN system office room 【HEN16H-HENS2AHENS8Q8-HENH1688】

X-Link PRODUCT MANUALS FOR MULTIVIEW CONTROLER

This manual applies to the following models: 3UA Multiview CONTROLER ( Optional Front Panal,LCD Console ) 3UB Multiview CONTROLER ( Optional Front Panal,LCD Console ) 8U Multiview CONTROLER ( Optional Front Panal ) 8U-S Multiview CONTROLER( Optional Front Panal ) 12U Multiview CONTROLER LED Very-large Dot Matrix Screen Multiview CONTROLER ( K Series ) Monitoring Multiview CONTROLER ( N Series ) 3D Multiview CONTROLER ( 3D Series ) 4K Multiview CONTROLER (4k Series ) IMPORTANT NOTICE The company reserves the right to update the manual according to improvement of products without any prior notice. In the process of using, if any content in this manual is inconsistent with actual products or there is any further question during use, please contact document information department of our company. Please read this manual carefully before using the CONTROLER and properly file it after reading for future reference. Pictures are for reference only, subject to our available products. Please pay close attention to those with the Icon of in the article.

阿特拉斯空压机控制面板操作说明

阿特拉斯空压机控制面板操作说明 1--启动按钮 (此按钮可用来启动压缩机。指示灯(8)点亮，表示EⅡ电脑控制器正在运行。) 2—显示屏 (显示有关压缩机的工作状况,保养及故障信息) 3—滚动键 (此键可用向上或向下滚动显示屏) 4--制表位键TAB (按此键,可以选择水平箭头标示的参数,只能修改后面有水平箭头的参数.) 5—功能键 (功能键可以用来控制和设定压缩机) 6--电源指示灯 (指明已接通电源) 7—综合报警指示灯(如果存在报警,保养报警,则该指示灯会亮起)

8—自动运行指示灯(指明电脑控制器正在自动运行) 9---停机按钮(按下此按钮,可以停止运行压缩机.(8)会熄灭。在卸载情况下运行30秒后，压缩机将停止运行) S3—紧急停机按钮（按此按钮，可以在紧急情况下立即停止压缩机，排除故障后拔出按钮以解除锁定。）开机前 1、检查油位。油位指针必须指在绿色区域的上部或高于该区域。 2、如果空气过滤器保养指示器的彩色部分完全显示出来，更换空气过滤器芯，参考使用说明书复位保养指示器和保养报警时钟。开机 1、合上电源。检查电源指示灯（6）是否点亮。 2、打开空气出气阀。 3、关闭冷凝液排污阀。 4、按开机按钮I。空压机开始运行，自动运行指示灯（8）点亮，开机后10秒，空压机开始加载运行。在运行中 1、经常检查油位，在加载中，指针必须位于绿色区域。 2、如果指示灯（8）点亮，电脑控制器正自动控制压缩机的加载，卸载，停机和重新启动。 3、经常检查显示屏（2）：空压机的运行状态通过图标显示在显示屏上。 4、如果报警指示灯（7）点亮或闪烁，请排除故障，参考使用说明书。如果需保养，停机并执行保养措施，参考使用说明书。停机 1、按停机按钮O。指示灯（8）熄灭。空压机大约卸载运行30秒后停机。 2、在紧急情况下停机，按控制面板旁的红色紧急停机按钮，报警指示灯（7）闪烁。在重新开机前拨出按钮并按重新设置键解除锁定。 3、关闭空气出气阀并切断电源。

产品说明书范文英文版

产品说明书范文英文版电子产品说明书——媒体音响英文说明书范例(中英) 便携式多媒体音响 Portable Multimedia Acoustics 使用说明书User’s Manual 专注于完美音质的追求?? Concentrate on perfect sound pursuit? 感谢您使用本公司出品的数码产品，为了让您轻松体验产品，我们随机配备了内容详尽的使用说明，您从中可以获取有关产品的介绍，使用方法等方面的知识。在您开始使用本机之前请先仔细阅读说明书，以便您能正确的使用本机，如有任何印刷错误或翻译失误望广大用户谅解，当涉及内容有所更改时，恕不另行通知。 Thank you for using this digital product of our company. In order to let you experience the product swimmingly, detailed instruction is provided which you can find the product’s introduction, usage and other information. Before using this product, please read the manual carefully, so that you can correctly use it. In case of any printing or translation error, we apologize for the inconvenience. As for the content change, we are sorry for no further notice. 一、产品概述 General Information 本机是一款外观小巧，设计精美、携带方便多媒体小音响，适用于家居、户外旅游、办公室等场所，随时随地享受音乐

(完整版)阿特拉斯空压机操作说明

1 显示屏-键 1 典型显示图显示器有四行：1 前三行:——显示屏显示传感器的名称和实际的读数。 ——测量值的单位和传感器的实际读数。 ——关于空压机运行的信息（空压机停机，等等），保养要求（比如油过滤器和空气过滤器）或者是故障信息（比如故障停机）

2滚动键（↑↓）:——这些滚动键标有垂直的箭头，允许滚动显示屏。 ——只要在显示屏的最右边的位置上有一个指向下面的箭头，其对应的滚动键就可以用来查阅下面的内容 3 表格键( = ):该键标有两个水平箭头，允许操作者选择标有水平箭头的参数。只有后面跟着指向右面的箭头的参数才可以修改, 3功能键(F1/F2/F3):——用于查阅或编制设定值, ——复位电机过载，故障停机或保养信息，或紧急停机, ——查看电脑控制器收集到的所有参数, ——(F1/F2/F3)所对应的功能根据显示的菜单变化而变化，它们的实际功能显示在显示屏的底部，刚好在相应的功能键的上面。最常用的功能中英文对应如下: Automatically Loaded 自动加载 Automatic Operation 自行运行 matically Loaded 自动卸载 Locally controlled 本地控制 Remote controlled 遥控控制 Manual Operation 手动运行 Manual Unloaded 手动卸载 Unioad 卸载 Running hours 运行时间 Loading hours 加载时间 Main Screen 主显示屏 Shutdown 故障停机 Compressor Outlet 压缩机排气口 Show More 更多 Add 增加指令用来增加空压机的自动启动/停机(日期) Back 返回指令返回到的选择或菜单 Cancel 取消当设定参数有误时.用来取消已设定的数 dleete 删除用来删除空压机的自动启动/停机时间 Help 帮助帮助寻找Atlas Copco的内部地址 Limits 上下限显示允许设定的上下极限数据 Load 负载手动操作空压机负载 Main screen 回到主目录从任一画面回到主目录 Menu 菜单 Modify 修改修改设定参数 Status Data 状态参数 Shutdown 故障停机 Shutdown Warning 故障停机报警 Motor overload 电机过载 Running Hours 运行时间 Program 编写输入将新的设定数据编写输入 Reset 重新设定重新设定计时器及信息,定时器或复位 Rtrn 回归回归到前一页或前一目录 Maximum 最大值 Shutdown Maximum 故障停机最大设置值 Reset 复位

阿特拉斯使用说明书

200 阿特拉斯*科普柯固定式空气压7 GA55 - GA75 - GA55 W - GA75 W 奉Elektro nikon II 总驕變訓愿使用说明书 44 2920 1464 02 No. 2920 Reg Elektro ni ko n I I 2920 1461 Ox 1464 02 0C/2000 / 38 / 988 JL 特阿婷取条*輯普KU 權札林陈介? 优同覗轉轟备注: 帝机 -GA90C - GA90C

*取乐 ■ fu 匕明H 同t 了压畑 I* 尸：>j A f O f-4- ■构J. 崎用才 Fiq il 專规* 杆 In f 务 Jri-U .廉?d i. ct jJ <> 4春 ?A [JL ￡車 ★昨 M 舸内客 1 ........................................ 1.1 ....................................................................... 1.1.1 ................................................................ 3 3.5 . .... ......... ...25 3 3.6...；..,..... .26 4 3.7 ........... ...' .................................. .. ..26 5 6 4 命 ....... ...27 o 8 4.1................ ..27 8 4.2 ............. ..27 8 4.3 ............. (29) 8 4.3.1 Atlas Copco ........... i ........... .............. . .29 8 4.3.2.. .29 8 4.4 ......... . .■L ?W ?K .I W ：>I ......... ..29 8 4.5....“....... ...■ ......................................... ...30 9 4.6 ............... ..30 10 10 5 .................. 馭理..書...... ..30 10 5.1......- ......... ................................................ .30 14 5.2 ........... ..30 14 5.3 .......... ;..... ..30 14 14 6 ............. ....... ■...■.…■;...■.... :. J .31 14 7 (32) 7.1 ................ ..32 15 7.2 .......... ...32 15 B L 7.3 ..33 16 7.3.1 ’ GA55/GA55W .....^ ..................... ...33 18 7.3.2 GA75/GA75W ......^ ............... ...33 18 7.3.3 GA90C/GA90CW .....彳....... ...34 18 7.3.4.. ............ .34 19 7.4..,：........ .................. ..34 19 7.5.............■.. - .34 20 7.5.1.. ...■_■.■■..■■ ................................. ..34 21 7.5.2.. - (35) 7.5.3 GA55/GA55 W W orkplace ........................... ...35 21 7.5.4 GA55/GA55 W W orkplace FF ...................... ...35 21 7.5.5 GA75/GA75 W W orkplace ........................... ...36 21 7.5.6 GA75/GA75 W W orkplace FF ...................... ...36 21 7.5.7 GA90C/GA90C W W orkplace ......................... .37 21 7.5.8 GA90C/GA90C W W orkplace FF .... (37) 22 7.6 ......... :..... ...... (38) 22 23 8 ?L ：... . ..39 24 24 25

完整版阿特拉斯空压机操作说明

MKIV 控制器操作说明停车按钮启动按钮显示器上下滚动键制表键通电指示灯故障报警指示灯自动控制运行灯功能键报警运行电源紧急停车按钮 1 2 3 4 5 6 7 8 9 10 11 12 S2 1 2 3 S2 $ 9 8 11 10 7 12 6 9

1显示屏-键 1典型显示图显示器有四行：i前三行：一一显示屏显示传感器的名称和实际的读数。――测量值的单位和传感器的实际读数。

――关于空压机运行的信息（空压机停机，等等），保养要求（比如油过滤器和空气过滤器）或者是故障信息（比如故障停机）

2滚动键(TJ)：这些滚动键标有垂直的箭头，允许滚动显示屏。 ——只要在显示屏的最右边的位置上有一个指向下面的箭头，其对应的滚动键就可以用来查阅下面的内容 3 表格键( = )：该键标有两个水平箭头，允许操作者选择标有水平箭头的参数。只有后面跟着指向右面的箭头的参数才可以修改, 3 功能键(F1/F2/F3)：——用于查阅或编制设定值, ——复位电机过载，故障停机或保养信息，或紧急停机, ——查看电脑控制器收集到的所有参数, ――(F1/F2/F3)所对应的功能根据显示的菜单变化而变化，它们的实际功能显示在显示屏的底部，刚好在相应的功能键的上面。最常用的功能中英文对应如下：Automatically Loaded自动加载 Automatic Operation自行运行 matically Loaded自动卸载 Locally controlled本地控制 Remote controlled遥控控制 Manual Operation手动运行 Manual Unloaded手动卸载 Unioad卸载 Running hours运行时间 Loading hours加载时间 Main Screen主显示屏 Shutdown故障停机 Compressor Outlet压缩机排气口 Show More更多 Add增加指令用来增加空压机的自动启动/停机(日期) Back返回指令返回到的选择或菜单 Cancel取消当设定参数有误时.用来取消已设定的数 dleete删除用来删除空压机的自动启动/停机时间 Help帮助帮助寻找Atlas Copco的内部地址 Limits上下限显示允许设定的上下极限数据 Load负载手动操作空压机负载 Main screen回到主目录从任一画面回到主目录 Menu菜单 Modify修改修改设定参数 Status Data状态参数 Shutdown故障停机 Shutdown Warning故障停机报警 Motor overload电机过载 Running Hours运行时间 Program编写输入将新的设定数据编写输入 Reset重新设定重新设定计时器及信息,定时器或复位 Rtrn回归回归到前一页或前一目录 Maximum最大值 Shutdown Maximum故障停机最大设置值 Reset复位

产品说明书中文英文

深圳市慧拓鑫科技有限公司 Shenzhen Hui Tuo Xin Technology Co., Ltd. 产品资料 Product information 1、TOP电源防雷箱系列（TOP Power lightning protection box series）产品介绍Product introduction TOP电源防雷箱系列依据IEC标准设计，8/20波形最大通流容量20KA-100KA，能对电源系统的浪涌电压进行有效的钳制，电源B、C、D级产品均具备。 TOP Power lightning protection box series is designed according to IEC

standard, 8/20 wave maximum flow capacity of 20KA-100KA, to power system voltage surge effectively clamped, power supply B, C, D products have. TOP电源防雷箱配系列具备测试指示灯功能，能有效的指示防雷箱工作电源、浪涌防护状态，并可选备雷击计数、远程遥信监测功能。 TOP Power lightning protection box series Have a test indicator function，Can effectively indicate the lightning protection box power supply、Surge protection status And optional lightning counting、Remote remote monitoring function ★电涌保护器失效报警功能/相零反接及接地不良报警 ★（Surge protection device failure alarm function / Phase zero reverse connection and grounding alarm） ★雷击计数显示、电源指示功能（可选） ★ Lightning counting display，Power indicator function（Optional） ★电浪保护器远程监测功能（失效） ★ Remote monitoring function（Failure） ★残压低、响应时间快 ★ Residual depression and Fast response time ★安装设计人性化、结构严谨 ★ Installation design of humanity and Strict structure ★工作环境温度适应性强 ★ Working environment temperature adaptability

阿特拉斯空压机操作说明

MKIV控制器操作说明1 停车按钮 2启动按钮 3 显示器 4 上下滚动键 5 制表键 6 通电指示灯 7 故障报警指示灯 8 自动控制运行灯 9 功能键 10 报警 11 运行

1 显示屏-键 1 典型显示图显示器有四行：1 前三行: ——显示屏显示传感器的名称和实际的读数。 ——测量值的单位和传感器的实际读数。 ——关于空压机运行的信息（空压机停机，等等），保养要求（比如油过滤器和空气过滤器）或者是故障信息（比如故障停机）

2滚动键（↑↓）:——这些滚动键标有垂直的箭头，允许滚动显示屏。 ——只要在显示屏的最右边的位置上有一个指向下面的箭头，其对应的滚动键就可以用来查阅下面的内容 3 表格键 ( = ):该键标有两个水平箭头，允许操作者选择标有水平箭头的参数。只有后面跟着指向右面的箭头的参数才可以修改, 3功能键(F1/F2/F3):——用于查阅或编制设定值, ——复位电机过载，故障停机或保养信息，或紧急停机, ——查看电脑控制器收集到的所有参数, ——(F1/F2/F3)所对应的功能根据显示的菜单变化而变化，它们的实际功能显示在显示屏的底部，刚好在相应的功能键的上面。最常用的功能中英文对应如下: Automatically Loaded 自动加载 Automatic Operation 自行运行 matically Loaded 自动卸载 Locally controlled 本地控制 Remote controlled 遥控控制 Manual Operation 手动运行 Manual Unloaded 手动卸载 Unioad 卸载 Running hours 运行时间 Loading hours 加载时间 Main Screen 主显示屏 Shutdown 故障停机 Compressor Outlet 压缩机排气口 Show More 更多 Add 增加指令用来增加空压机的自动启动/停机(日期) Back 返回指令返回到的选择或菜单 Cancel 取消当设定参数有误时.用来取消已设定的数 dleete 删除用来删除空压机的自动启动/停机时间 Help 帮助帮助寻找Atlas Copco的内部地址 Limits 上下限显示允许设定的上下极限数据 Load 负载手动操作空压机负载 Main screen 回到主目录从任一画面回到主目录 Menu 菜单 Modify 修改修改设定参数 Status Data 状态参数 Shutdown 故障停机 Shutdown Warning 故障停机报警 Motor overload 电机过载 Running Hours 运行时间 Program 编写输入将新的设定数据编写输入 Reset 重新设定重新设定计时器及信息,定时器或复位 Rtrn 回归回归到前一页或前一目录 Maximum 最大值

如何翻译英文说明书

如何翻译英文说明书【篇一：英语药品说明书的翻译】英语药品说明书的翻译英语药品说明书由以下12项内容组成，大多数英语药品说明书结构基本相同。 1. pakage insert (insert)说明书 2. drug name (medicine) 药品名称 3. description 性状 4. action 作用 5. indication适应症 6. contraindications 禁忌症 7. precaution注意事项 8. side effects副作用 9. dosage and administration 剂量和用法 10. dacking 包装 11.expiry 失效期 12. manufactring date (manu.date)出厂日期 13.reference 参考文献药品名称一、英语药品说明书一般用商品名，由生产厂家向该国政府有关部门申请注册正式名称，受该国政府法律保护，在药品名称的右上角有个○r的符号，意思是已经申请注册的法定名称，不可随意改变名称。○r=recive 在药品之后有时issued to(for) the medical profession only短语，意：仅供医界参考。 r例：mobic ○ issued to(for) the medical prfession. 二、译法：分四种译法 1. 音译：按英语读音用相应的汉字译出例： mobic莫比可 rifampicin利福平 2. 意译：按药品名称各组成部份的英语意义译成汉语例： streptomycine是由strepto和mycine组成，其中 strepto(链球状)，mycine(霉素)，则按英语意思，译成：链霉素。因此必须掌握大量前、后缀，才以准确翻译，此种译法多数是抗生素类药物。 nitroglycerine 由nitro(硝基)+glycerin(甘油)组成，则意为硝酸甘油 aminophylline由amino+phylline译:氨茶碱 3. 音意并译：按英语药名组成，前面部份按音译，后面部份按意译。例：kanamycine由kama(卡那)+mycine(霉素)组成，按前音后的方法，译为卡那霉素。

阿特拉斯使用说明书

阿特拉斯使用说明书 1

GA55 - GA75 - GA55 W - GA75 W - GA90C - GA90C W Elektronikon II ? ? 2920 1461 0x 44 2920 1464 ? ?

Elektronikon I I No. 2920 1464 02 Reg 0C/ / 38 / 988 200 .co m

1 (3) 1.1 (3) 1.1.1 (4) 1.1.2 (5) 1.1.3 (6) 1.2 (8) 1.2.1 (8) 1.2.2 (8) 1.3 Elektronikon (8) 1.3.1 (8) 1.3.2 (8) 1.3.3 (8) 1.3.4 (9) 1.4 ..................................................................................... . . 10 1.5 ..................................................................................... . . 10 1.5.1 .............................................................................. . . 10 1.5.2 .............................................................................. . . 14 1.5.3 .............................................................................. . . 14 1.6 GA FF ............................................. . 14 1.6.1 ................................................................................ . 14 1.6.2 ............................................................................ . . . 14 2 ........................................................... . . 15 2.1 ....................................................................................... . 15 2.2 ................................................................................... . . . 16 2. 3 ....................................................................................... . 18 2.3.1 For GA55/GA55 W . . . ..................... . . . 18 2.3.2 For GA75/GA75 W . . . ..................... . . . 18 2.3.3 For GA90C/GA90C W . . . .............. . . . 19 2.4 ................................................................................... . . . 19 2.5 ....................................................................................... . 20 2.6 ..................................................................................... . . 21 3 ........................................................... . . 21 3.1 ....................................................................................... . 21 3.1.1 .............................................................................. . . 21 3.1.2 ............................................................................ . . . 21 3.1.3 ................................................................................ . 21

产品说明书英文版(DOCX 39页)

产品说明书英文版(DOCX 39页) 部门： xxx 时间： xxx 整理范文，仅供参考，可下载自行编辑

X-Link PRODUCT MANUALS FOR MULTIVIEW CONTROLER

产品英语说明书

spiral chute 1、 product description spiral chute is integrated spiral separator, spiral chute, shaker, centrifugal concentration machine characteristics of the equipment, mining, mineral processing is the best equipment, especially the seaside, riverside, sand beach, the stream of placer mining is more ideal. the product has the advantages of reasonable structure, simple installation, covers an area of small, simple operation, stable ore beneficiation, clear, large processing capacity, high efficiency enrichment ratio high, high recovery rate, reliable operation characteristics. have weight light, moisture-proof, rust-proof, corrosion resistance, of the feeding quantity and concentration, particle size, quality of volatility adaptability is strong, no noise. 2、 separation principle spiral chute is a membrane flow gravity separation equipment, the selection principle is the use of useful minerals and gangue in proportion, particle size, shape differences, in rotating inclined flow by gravity, centrifugal force, hydrodynamic pressure and friction force with different groove face, realize the useful minerals and gangue stratification, branch tape sorting. heavy, coarse granularity, fast sedimentation of particles gradually moved towards the spiral groove inner edge, the proportion of small, fine particle size, particle sedimentation slow gradually moved to the spiral groove edge, gradually banding, culminating in the spiral groove end by cutting ore tank is respectively connected out, to realize separation. 3、 application the sorting equipment for grain size 0.3--0.02 mm fine iron ore, titanium ore, chromite, pyrite, zircon, monazite, rutile , phosphorus ore, tungsten, tin, b mine of tantalum niobium ore with the difference of specific gravity, and other non-ferrous metals, rare metals and non-metallic mineral. the sorting process with a stable, easy to control, to allow changes to the mineral concentration range, high enrichment, high recovery rate, small occupation area, little water consumption, simple structure, no need of power, large processing quantity, simple installation, convenient operation, small investment, quick advantages. 4、the method of use the spiral chute is erected, calibrated vertical line, with metal or wood fixed in position, by the sand pump will ore to spiral top two inlet, adding supplemental water, mineral ore concentration regulation paddle, paddle down naturally from high swirl, in rotating inclined flow produces a kind of inertial centrifugal force, with ore proportion, particle size, shape differences, swirl through the action of gravity and centrifugal force, will be mine and sand separating, concentrate into the concentrate pipe connected with a hopper, tailings into tailing bucket a pipeline is connected to a sand pool, then the pump discharge, finished processing the whole process. 5、structure and technical parameter 6、installation spiral chute installation procedures and requirements: 1) first check the glass steel spiral slice quality (especially the work surface