轮胎专用模具术语(中英文对照)
Mold Terminology模具术语
AD-Diameter The tread diameter at the centerline of the tread (EU); also: "T-Diameter"(GT)
AD直径：指胎面中心线直径（EU）。又叫T直径（GT）
Auto-lock Ear A Lug on the cone ring used to mount the mold/container in the top half of a 60“ NRM
Auto-lock press.
导环上的突缘，用于和60“ NRM Auto-lock 硫化机上半部连接。
Bead Ring The tire bead forming ring (also: toe ring)
钢圈，也称toe ring
Bead Ring Register The landing and tapered seat that the bead ring fits into
钢圈配合：侧板上，和钢圈配合的平面及锥面
Bottom Container Plate The plate that the bottom sidewall plate is bolted to
模壳底座
Bottom Container Plate Lifting Lug A lug attached to the Bottom Container Plate with Horizontal holes used for lifting.
模壳底座吊耳：装配在底座上、有水平的孔，用来吊装的吊耳
Bottom Container Plate Dowel Pin Lug A lug attached to the Bottom Container Plate that supports the Dowel Pin Bushing.
装配在底座上，用来支承定位销套的突缘
Bottom Container Plate Hold Down A lug that is used to fix the Bottom Plate in the Press.
用来将底座装配在硫化机上的突缘
Breaker Hook A hook fixed to the bottom of the tread segment that catches the bottom container plate only when the segment will not release from the tire during de-molding.
分离钩：固定在花纹块底部的钩子，轮胎硫化完后若花纹块不能跟轮胎分离，就用此钩抓住模壳底座帮助花纹块和轮胎进行分离。
Breaker Hook Guide Piece
A block bolted to the breaker hook that aligns the tread segment with a slot in the bottom container plate.
分离钩导块：用螺栓固定在Breaker Hook上，定位花纹块和模壳底座上槽的定位块。
Bronze Wear Plates Any sacrificial metal plate placed under, over or behind a component to keep the components from wearing on each other (greasing)
青铜耐磨板(油润滑的)
Casting An un-machined cast metal tread ring or Segment
铸件：未加工的金属花纹圈或花纹块铸件。
Centering Ring The ring mounted on the bottom press platen to locate the mold/ container concentrically to the press; also: "Press register"
定中环,也称“Press register”
Clamp Rings The bladder clamping assembly
胶囊夹盘
Cone Ring The outer ring that transforms the axial movement of the press in a radial one of the segments; also: "Actuator ring", "Squeeze ring" (GT)
导环，也称"Actuator ring", "Squeeze ring"
Conicity Difference between tread radius over the width
锥度
Container The mechanical parts that allow a segmented mold to operate; also: mechanism (GT)
模壳,也叫mechanism
Container Cavity The space inside of the container that the mold fits into
模壳内腔：模壳内部放置模具的空间。
DD-Diameter Nominal diameter of a bead ring (EU) Also: "Heel diameter" (GT)
钢圈的公称直径, 也叫"Heel diameter"
Decoupler Rib A narrow rib that runs circumferentially around the mold and is located near the shoulder area
在胎肩部位、窄的的圆周向的花筋
DEVA Metal Graphite impregnated bronze metal used for wear plates in segmented molds (un-greased)
DEVA类耐磨板：石墨青铜金属，用来制作活络模具的耐磨板（自润滑）。
Dowel Pins The pins that keep the mold halves and parts aligned (containers or HKK molds)
定位销：用来对模具的半模或零件定位的销（模壳或HKK模具）。
Dowel Pin Bushing A replaceable sleeve used to register the Dowel Pin locations.
定位销套：对定位销进行定位的可更换的衬套。
DS 2-Diameter The junction diameter between the sidewall plate and the tread segments or tread ring and mould back cavity (EU); also: "S Diameter"(GT)
口径：侧板与花纹块、花纹圈与mould back 的配合直径. 也叫"S Diameter"
End Gap The distance between cold mold segments (20°C) that allows for heat expansion
竖缝间隙：20°C时花纹块竖缝允许热膨胀的间隙
Exterior Mold Identification Plate A removable plate fastened to the outside of the cone ring listing information pertaining to the mold parts (tread segments, side-plates) assembled in the container.
模壳铭牌
Filler rings Full sidewall inserts for molds that fills from the off shoulder area to the I.D.
嵌入式侧板:从肩部到内径，全部嵌入模具的侧板
Front of mould The reference point at which all dimensional locations are referred
模具正前方
Heel Diameter See: DD-Diameter
见DD-Diameter
Guide Piece A block fixed to the Top Container Plate that registers to a slot in the Cone Ring to keep the Top plate from turning during operation.
导向块：固定在上盖上，和导环上的槽定位，防止操作过程中上盖转动
Insert Metal plates pushed or screwed in the side wall plate for exchangeable information活字块(牌) Insulation Jacket Insulation placed around a container or 2 piece mold (GT) to retain heat
保温套
Integral type mechanism A mold (tread area) and mechanism that are one unit
整体式模壳: 花纹部分和模壳是一体的
Ledge Height Bead ledge width on a bead ring
钢圈上凸出部位的宽度
Lettering The inside lettering of the sidewall; also: "Sidewall engraving" (GT)
侧板字体图. 也叫"Sidewall engraving"
Maxi Vent (GT) Vent Sleeve A removable insert for vent holes (Dia.:1,33 mm) to be trimmed.
大气孔套(直径.:1,33 mm)
Mechanism (GT) See: container or semi-container
见container 或semi-container
Micro Vent A removable insert with vent slots (< 0.1 mm)
微型气孔套：（< 0.1 mm）
Mini Vent (MV) A removable insert for vent holes (Dia.: 0,6 mm)
迷你气孔套(直径.:0.6 mm)
Mold Back The part of a two piece mold machined to hold the tread ring and filler rings
除花纹圈和嵌入侧板外的两半模外壳
Mold Cavity The inside of the mold that the tyre is shaped in
模具内腔：形成轮胎外型的模具内部曲线
Mold Register The taper at the O.D. of a 2 piece mould that aligns the mold concentrically
两半模具上下半模的定位锥面
Pitch length Repeated element of tread
节距长度
Preload Compression in the parts of the mold, which is proportional to a step off from the cone ring to the top container plate
预加载
Press Drilling Any bolt holes to attach the mold/container to the press
模具和硫化机连接的螺栓孔
Press Register See: Centering Ring
见Centering Ring
PT-100 Hole A hole in one segment or the bottom half of a two piece mold to accept a PT-100 feeler.
在一个花纹块上或在两半模底部的孔，可以放置PT-100探针
Radial Stroke The distance the tread shoe travels in and out
径向行程
S Diameter (GT) See: DS 2-Diameter
见DS 2-Diameter
Segment Stop Blocks Blocks or bolts through the Cone Ring that keep the segments from coming out
限位块
Segmented mould Moulds consisting of multiple tread segments and a top and bottom sidewall plate and bead ring
活络模具
Semi-Container Container without segment shoes (profile segment and segment shoe are combined In
花纹块和滑块一体的模壳
Shim ring The removable ring on the top of the cone ring that allows for shims to increase or decrease
Pre-load
安装环
Shipping Bolt A device for the transfer to keep all parts of the container together
运输用固定螺栓
Shipping Plate A plate used with the shipping bolt and placed on the top surface of the container to keep the container parts together during transfer.
运输用固定板
Shoulder Area The area where the tread and sidewall meet ; also: "Pennant area", "Buttress area" (GT)
胎肩，也称"Pennant area", "Buttress area"
Sidewall-Plate Ring, which is bolted at the container plate and contains the shape of the sidewall
侧板
Sipe A small steel insert in the tread ;also: "Blades" or "Kerfs" (GT)
钢片（嵌入式），也称"Blades" or "Kerfs"
Sipe Tab The portion of the sipe that is buried in the mold.
钢片埋入模具的部分
Slide Block Retainer "T" it connects the tread-shoe with the dovetail slide
导向条
SMO (Segmented mould operator) The kit to rework a press for a segmented mold
活络模具动作
Stamping The generic term for all mold indication.
标识
Steam Baffle A plate welded in the steam chamber between the live steam inlet and outlet openings in the cone ring.
(导环汽室中的)隔汽板
Steam Chamber The chamber in the cone ring that allows live steam to circulate around the container (EU: also located in the bottom container plate)
(导环)蒸汽室
Steam Jacket A band welded at the outer diameter of the cone ring to enclose the steam chamber.
(导环汽室的)围板
T Diameter (GT) see: AD-Diameter
见AD-Diameter
Thermo-Channel Slot A groove, usually located in the bottom plate, use to guide wires through for Thermo-couples.
测温槽，通常在下侧板上
TIR (Total Indicator Reading(应该是run-out)) The readings taken in a circle to establish the shape of the plane measured
跳动
Top Container Plate The plate that the top sidewall plate is bolted to
上盖
Transport Bushing A replaceable sleeve welded horizontally in the outer diameter of the cone ring for mold handling.
Tread Rib The detail in the tread of a mold that makes the groove in the tire one piece)
花筋
Tread Ring The cast tread portion of a 2 piece mold (GT)
两半模的铸造花纹圈
Tread Segments Shoulder to shoulder tread casting cut in several segments
花纹块
Tread Segment Guide Piece A slide that fixes the tread segment to the top container plate to retract the segments with the SMO.
上滑块
Tread Shoe The portion of a segmented mold that moves the tread segment in and out.
滑块
Tread Shoe Slide Slide that is fixed to the back of the tread segment and guides the segment with a slot in the cone ring.
滑块背面的耐磨板
Two-Piece Mold A mold with a top and bottom half
两半模具
Converter A removable block containing tapped holes for fixing the mold/container in the top half of the press.
过桥板
塑胶模具类中英文对照专业术语
塑胶模具类中英文对照专业术语工程部/ Design department: 1) Designer - 设计师。 2) Assembly drawing - 模具组装图。 3) Mold layout - 模具结构图。 4) 2D product drawing - 2D产品图。 5) 3D product data - 3D产品数据。 6) Part drawing - 散件图。 7) Insert molding - 镶件模。 8) 2 color mold / Double injection tool - 双色模。 9) Hydraulic system - 油/水压系统。 10) Parting line - 分模线。 11) Air venting - 排气槽。 12) Cooling system - 冷却系统。 13) Screw - 镙丝。 14) Hot runner system - 热流道。 15) Valve gate - 伐针入水口。 16) Fan gate - 扇型入水口。 17) Pin point gate - 针点进胶。 18) Moon gate / Banana gate - 香蕉，象牙入水口。 19) Submarine gate - 潜水口。 20) Injection machine tonnage - 注塑机吨数。 21) Number of cavity - 穴数。 22) Steel - 钢材。 23) Copper - 铜。 24) Tungsten copper - 钨铜。 25) Beryllium copper - 铍铜。 26) Hardening - 加硬/淬火。 27) Tempering - 回火。
模具术语(中英文对照)
AD-Diameter The tread diameter at the centerline of the tread (EU); also: "T-Diameter"(GT) AD直径：指胎面中心线直径（EU）。又叫T直径（GT） Auto-lock Ear A Lug on the cone ring used to mount the mold/container in the top half of a 60“ NRM Auto-lock press. 导环上的突缘，用于和60“ NRM Auto-lock 硫化机上半部连接。 Bead Ring The tire bead forming ring (also: toe ring) 钢圈，也称toe ring Bead Ring Register The landing and tapered seat that the bead ring fits into 钢圈配合：侧板上，和钢圈配合的平面及锥面 Bottom Container Plate The plate that the bottom sidewall plate is bolted to 模壳底座 Bottom Container Plate Lifting Lug A lug attached to the Bottom Container Plate with Horizontal holes used for lifting. 模壳底座吊耳：装配在底座上、有水平的孔，用来吊装的吊耳 Bottom Container Plate Dowel Pin Lug A lug attached to the Bottom Container Plate that supports the Dowel Pin Bushing. 装配在底座上，用来支承定位销套的突缘 Bottom Container Plate Hold Down A lug that is used to fix the Bottom Plate in the Press. 用来将底座装配在硫化机上的突缘 Breaker Hook A hook fixed to the bottom of the tread segment that catches the bottom container plate only when the segment will not release from the tire during de-molding. 分离钩：固定在花纹块底部的钩子，轮胎硫化完后若花纹块不能跟轮胎分离，就用此钩抓住模壳底座帮助花纹块和轮胎进行分离。
鞋业(类)常用术语中英文对照
鞋业（类）常用术语中英文对照 --－欧维思品牌鞋业折扣店 --https://www.360docs.net/doc/222149288.html, 目录 第一章：Stage 阶段………………………………P2-P10 第二章技术……………………………P7-P15 第三章鞋型转移……………………………P16-P17 欧维思品牌鞋业折扣店招商加盟网--https://www.360docs.net/doc/222149288.html,- 1 -
第一章：Stage 阶段 ----欧维思品牌鞋业折扣店https://www.360docs.net/doc/222149288.html, I.3.1. Two main sections in Dev. Division 开发的两大部分： 1. Development section: explain more in process of new models to make samples in order to introduce market to achieve qty. 开发部分：此部分着重于新型体的样品制作，以便可介绍给客户来争取一定数量的订单。 https://www.360docs.net/doc/222149288.html,mercialization section: explain more in process of technical after it was developed with Fitting test and Wear test to ensure that all products meet consumers’ expectations in terms of Fitting, Comfort and Performance. 技术部分：开发转移到技术部门，此阶段着重于在开发阶段完成试穿测试, 确保产品在试穿/舒适/功能方面可满足客户的要求后进行的技术工作。 I.3.2. Development Stages 开发阶段 I.3.2.1. PPR: Pre Prototype Review 初始线条评估 1st stage to review all sample products Internally by customer ( Marketing,designer,L.O) For performance shoes, we have Fitting and Wear Test Sample to be sent. * The topics of review are : 1. Material 2. Quality 3. Performance 4. Price 5. Color 6. Design 7. Forecast 客人内部（市场销售、设计师、本地客人）对于新鞋型第一阶段之评估。 对于功能性鞋型，我们要寄Fitting test &Wear test试穿样品。 此时检查要点如下： 1、材料 2、品质 3、功能 4、价格 5、颜色 6、设计 7、订单预测 I.3.2.2. PFR:Prototype Final Review 最后线条评估 Final stage to review all sample shoes before introducing the products to the customers. At this time, all key points should be finally decided (Pattern / Design, Color,Price, Material (should be released), etc.). The result of Fitting Test should be considered for PPR meeting as a basic. 在全部新鞋型介绍给客户前之最后检查阶段，此时所有要点均需做出最后确定，如：纸版、设计、颜色、价位、材料（必须是通过了测试）等等。 寄出试样鞋时需附上试穿报告。此时的试穿结果是PPR 会议之基本考量点。 I.3.2.3. SMS1:Salesman Sample 1 销样一 欧维思品牌鞋业折扣店招商加盟网--https://www.360docs.net/doc/222149288.html,- 2 -
常用金融术语(中英对照)
熟练掌握名目繁多金融术语除了是专业人士的必修课外，在金融渗透、人人参与投资的时代，了解一些常用的金融术语也对普通投资者们大有益处。本文就为你详细列举了一些常用的可中英文对照的金融术语，帮助你了解生活中的金融。 金融 资产组合(Portfolio):指投资者持有的一组资产。一个资产多元化的投资组合 通常会包含股票、债券、货币市场资产、现金以及实物资产如黄金等。 证券投资(Portfolio Investment) :国际收支中、资本帐下的一个项目，反映资 本跨国进行证券投资的情况，与直接投资不同，后者涉及在国外设立公司开展业务，直接参与公司的经营管理。证券投资则一般只是被动地持有股票或债券。 投资组合经理(Portfolio Manager):替投资者管理资产组合的人，通常获授权 在约定规范下自由运用资金。共同基金的投资组合经理负责执行投资策略，将资金投资在各类资产上。 头寸(Positio n):就证券投资而言，头寸是指在一项资产上做多(即拥有)或做空(即借入待还)的数量。 总资产收益率(ROTA):资产收益率是企业净利润与平均资产总额地百分比，也 叫资产回报率(ROA)，它是用来衡量每单位资产创造多少净利润的指标。其计 算公式为：资产收益率二净利润/平均资产总额X 100% ；该指标越高，表明企业 资产利用效果越好，说明企业在增加收入和节约资金使用等方面取得了良好的效果，否则相反。 整批交易(Round Lot Trade):指按证券和商品在市场最普遍的交易单位(例如 100股为一单位)进行的交易。 交易回合(Round Turn):指在同一市场上通过对两种证券或合约一买一卖，或 一卖一买的交易两相抵消。通常在计算手续费时会提及交易回合。
汽车专用术语中英文对照大全
汽车专用术语中英文对照大全 Automotive Electric System 汽车电系 Starting Motor 起动马达 利用齿轮传动来摇动引擎或起动引擎的电动马达。 Solenoid Switch 电磁开关 借着电磁线圈蕊的移动而使开关合的一种小开关装置。其蕊也会导致机械作用，如将传动小齿轮与飞轮的齿轮啮合，以激活引擎。 Halogen Headlamp 卤素头灯 一种灯泡内充满卤素的聚光大灯，其光度较一般头灯为亮。 Fuel Level Indicator 汽油表 分为装在驾驶室仪表板的表体及装在油箱上的量油器两部份。 Oil Pressure Gauge 机油压力表 通称为机油表，指示引擎内部机油压力的大小。至于油底壳中的机油量，需要引擎旁的机油尺测量。现今多数汽车以警告灯代替机油压力表。 Compressor 压缩机 空调系统的机件，可探冷却剂蒸气压缩以增加其压力及温度。 Condenser 冷凝器 空调系统的机件，能将管子中的热量，以很快的方式，传到管子附近的空气，大部分的汽车置于水箱前方。 Dehydrator 储液器和干燥器 安装在冷凝器和挥发器之间，靠近冷凝器，用来储存液体冷媒，并且将冷媒里的水份吸掉。 Refrigerant 冷媒 在空调系统中，透过蒸发与凝结，使热转移的一种物质。 Refrigerant Oil 冷冻油
润滑空调系统里的活动机件，实施空调工作时，必须重新充填。 Alternator 交流发电机 在汽车电系中，一种可将机械能改变成为电能的装置。由此可充电至电瓶，并可供应各电器的电力。 Suspension System悬吊系统 Coil Spring 圈状弹簧 圈状弹簧为独立式悬吊装置使用最多之弹簧，以弹簧钢卷成螺旋状。 Torsion-Bar Spring 扭杆弹簧 扭杆一端固定在车架上，另一端使用臂与车轮连接，车轮上下跳动时使扭杆扭转，以扭转弹力来吸收震动，构造简单占位置小，适合小型车使用，但材质要佳。 Stabilizer Bar 平稳杆 平稳杆属横向装置于车架与控制臂之间，其功用可减少悬吊系统的移动及车身摇摆，尤其汽车转弯时，因离心力作用，会使车身发生倾斜，此杆抗衡扭力的作用足以减轻汽车偏外的程度。 Shock Absorber 避震器 避震器的需求是由于弹簧不能马上稳定下来，也就是说弹簧被压缩再放开以后，它会持续一段时间又伸又缩，所以避震器可以吸收车轮遇到凹凸路面所引起的震动，使乘坐舒适。 Front Suspension 前悬吊 前悬吊系统使前轮可以上下移动并吸收路面震动，但是也须使车轮能左右摆动，以便汽车转向。除大货卡车外，大多的车辆已普遍采用独立式悬吊装置，左右轮互相无关系，为独立动作。 Rear Suspension 后悬吊 一般后悬吊系统会采用钢板弹簧，或螺旋弹簧，但现今轿车为使乘坐舒适，亦采用独立悬吊系，与前悬吊系相同，可以使四个轮子各自独立，为减少轮胎磨损及行驶稳定，需作后轮定位。 自动水平控制装置(Automatic Level Control)
模具术语翻译
模具名词中英文对照表序号中文名英文名 1一、水口gate 2进水位gate location 3水口形式gate type 4大水口edge gate 5细水口pin-point gate 6水口大小gate size 7转水口switching gate 8唧嘴口径sprue diameter 9二、流道runner 10热流道hot runner 11冷流道cold runner 12唧嘴直流direct sprue gate 13圆形流道round runner 14模流分析mold flow analysis 15流道平衡runner balance 16热嘴hot sprue 17热流道板hot manifold 18发热管cartridge heater 19探针thermocouples 20插头connector plug 21插座connector socket 22密封/封料seal 23三、运水water line 24喉塞line pug 25喉管tube 26塑胶管plastic tube 27快速接头jiffy quick connector plug 28四、模具零件mold components 29三板模three-plate mold 模具名词中英文对照表 序号中文名英文名 30二板模two-plate mold 31边钉/ 导边leader pin /guide pin
32边司/ 导套bush in g/guide bush ing 33顶针板ejector retainer plate 34托板support plate 35螺丝screw 36管钉dowel pin 37开模槽ply bar score 38内模管位core/cavity inter-lock 39顶针ejector pin 40司筒ejector sleeve 41司筒针ejector pin 42推板stripper plate 43缩呵movable core 44扣机（尼龙拉勾）n yl on latch lock 45斜顶lifter 46模胚（架）mold base 47母模cavity in sert 48公模core insert 49行位（滑块）slide 50 镶件in sert 51压座/斜鸡wedge 52耐磨板/ 油板wedge wear plate 53压条plate 54撑头support pillar 55唧嘴sprue bushing 56挡板stop plate 57定位圈locating ring 58锁扣latch 模具名词中英文对照表 序号中文名英文名 59扣鸡parti ng lock set 60推杆push bar 61栓打螺丝S.H.S.B 62顶板ejector plate 63活动臂lever arm
计算机算法常用术语中英对照
第一部分计算机算法常用术语中英对照 Data Structures 基本数据结构Dictionaries 字典Priority Queues 堆Graph Data Structures 图Set Data Structures 集合Kd-Trees 线段树Numerical Problems 数值问题Solving Linear Equations 线性方程组Fourier变换Bandwidth Reduction 带宽压缩Matrix Multiplication 矩阵乘法Satisfiability 可满足性Determinants and Permanents 行列式Linear Programming 线性规划Matching 匹配Constrained and Unconstrained Optimization 最值问题Clique 最大团Cryptography 密码Random Number Generation 随机数生成Shortest Path 最短路径recursion递归Factoring and Primality Testing 因子分解/质数判定Searching 查找Sorting 排序Arbitrary Precision Arithmetic 高精度计算Calendrical Calculations 日期 Discrete Fourier Transform 离散Combinatorial Problems 组合问题 Median and Selection 中位数Generating Permutations 排列生成 Generating Subsets 子集生成Generating Partitions 划分生成 Generating Graphs 图的生成Job Scheduling 工程安排 Graph Problems -- polynomial 图论-多项式算法Connected Components 连通分支Topological Sorting 拓扑排序Minimum Spanning Tree 最小生成树Transitive Closure and Reduction 传递闭包Network Flow 网络流 Eulerian Cycle / Chinese Postman Euler回路/中国邮路 Edge and Vertex Connectivity 割边/割点Independent Set 独立集 Drawing Graphs Nicely 图的描绘Drawing Trees 树的描绘 Planarity Detection and Embedding 平面性检测和嵌入Vertex Cover 点覆盖 Graph Problems -- hard 图论-NP问题Traveling Salesman Problem 旅行商问题Hamiltonian Cycle Hamilton回路Graph Partition 图的划分 Vertex Coloring 点染色Edge Coloring 边染色 Graph Isomorphism 同构Steiner Tree Steiner树 Feedback Edge/Vertex Set 最大无环子图Computational Geometry 计算几何 Convex Hull 凸包Triangulation 三角剖分 V oronoi Diagrams V oronoi图Nearest Neighbor Search 最近点对查询Range Search 范围查询Point Location 位置查询 Intersection Detection 碰撞测试Bin Packing 装箱问题 Medial-Axis Transformation 中轴变换Polygon Partitioning 多边形分割Simplifying Polygons 多边形化简Shape Similarity 相似多边形 Motion Planning 运动规划Maintaining Line Arrangements 平面分割Minkowski Sum Minkowski和Set and String Problems 集合与串的问题 Set Cover 集合覆盖Set Packing 集合配置 Approximate String Matching 模糊匹配Text Compression 压缩 DP—Dynamic Programming动态规划Longest Common Substring 最长公共子串Shortest Common Superstring 最短公共父串String Matching 模式匹配 Finite State Machine Minimization 有穷自动机简化
各式模具分类用语中英文对照
Landed plunger mold有肩柱塞式模具Burnishing die 挤光模 Landed positive mold 有肩全压式模具Button die镶入式圆形凹模 Loading shoe mold料套式模具Center-gated mold中心浇口式模具Loose detail mold 活零件模具 Chill mold 冷硬铸模 Loose mold 活动式模具 Cold hobbing冷挤压制模 Louvering die百叶窗冲切模Composite dies 复合模具 Manifold die分歧管模具 Counter punch反凸模 Modular mold 组合式模具 Double stack mold 双层模具 Multi-cavity mold多模穴模具Electroformed mold电铸成形模 Multi-gate mold复式浇口模具Expander die 扩径模 Offswt bending die双折冷弯模具Extrusion die 挤出模 Palletizing die 叠层模 Family mold反套制品模具 Plaster mold 石膏模 Blank through dies漏件式落料模Porous mold 通气性模具Duplicated cavity plate复板模Positive mold全压式模具 Fantail die扇尾形模具 Pressure die压紧模 Fishtail die鱼尾形模具 Profile die轮廓模 Flash mold 溢料式模具Progressive die顺序模 Gypsum mold 石膏铸模 Protable mold 手提式磨具 Hot-runner mold热流道模具Prototype mold 雏形试验模具 Ingot mold钢锭模 Punching die 落料模 Lancing die 切口模 Raising (embossing) 压花起伏成形Re-entrant mold 倒角式模具
常用保险术语(中英对照版本)
常用保险术语 保险费率 premium rate 单位保险金额应该收取的保险费。 损失 loss 非故意的、非预期的和非计划的经济价值的减少或灭失。通常分为直接损失和间接损失。 损失程度 loss severity 保险标的可能遭受的损失的严重程度。 直接损失 direct loss 由风险事故导致的财产本身的损失。 间接损失 indirect loss 由直接损失引起的额外费用损失、收入损失和责任损失等无形损失。 保险 insurance 投保人根据合同约定，向保险人支付保险费，保险人对于合同约定的可能发生的事故因其发生所造成的财产损失承担赔偿保险金责任，或者当被保险人死亡、伤残、疾病或者达到合同约定的年龄、期限时承担给付保险金责任的商业保险行为。 财产保险 property insurance 以财产及其有关利益为保险标的的保险。 企业财产保险 commercial property insurance 以单位、团体所有或占有的在指定地点的财产及其有关利益为保险标的的财产保险。 营业中断保险 business interruption insurance 以单位因停产、停业或经营受影响而面临的预期利润的减少及必要的费用支出为保险标的的财产保险。 机器损坏保险 machinery breakdown insurance 以各类已安装完毕并投入运行的机器为保险标的财产保险。 货物运输保险 cargo insurance 以运输途中的货物为保险标的保险。 海上货物运输保险 ocean marine cargo insurance 以通过海上运输方式运输的货物作为保险标的的保险。 陆上货物运输保险 inland transit insurance 以通过陆上运输方式运输的货物为保险标的的保险。
轮胎专用模具术语(中英文对照)
Mold Terminology模具术语 AD-Diameter The tread diameter at the centerline of the tread (EU); also: "T-Diameter"(GT) AD直径：指胎面中心线直径（EU）。又叫T直径（GT） Auto-lock Ear A Lug on the cone ring used to mount the mold/container in the top half of a 60“ NRM Auto-lock press. 导环上的突缘，用于和60“ NRM Auto-lock 硫化机上半部连接。 Bead Ring The tire bead forming ring (also: toe ring) 钢圈，也称toe ring Bead Ring Register The landing and tapered seat that the bead ring fits into 钢圈配合：侧板上，和钢圈配合的平面及锥面 Bottom Container Plate The plate that the bottom sidewall plate is bolted to 模壳底座 Bottom Container Plate Lifting Lug A lug attached to the Bottom Container Plate with Horizontal holes used for lifting. 模壳底座吊耳：装配在底座上、有水平的孔，用来吊装的吊耳 Bottom Container Plate Dowel Pin Lug A lug attached to the Bottom Container Plate that supports the Dowel Pin Bushing. 装配在底座上，用来支承定位销套的突缘 Bottom Container Plate Hold Down A lug that is used to fix the Bottom Plate in the Press. 用来将底座装配在硫化机上的突缘 Breaker Hook A hook fixed to the bottom of the tread segment that catches the bottom container plate only when the segment will not release from the tire during de-molding. 分离钩：固定在花纹块底部的钩子，轮胎硫化完后若花纹块不能跟轮胎分离，就用此钩抓住模壳底座帮助花纹块和轮胎进行分离。 Breaker Hook Guide Piece A block bolted to the breaker hook that aligns the tread segment with a slot in the bottom container plate. 分离钩导块：用螺栓固定在Breaker Hook上，定位花纹块和模壳底座上槽的定位块。 Bronze Wear Plates Any sacrificial metal plate placed under, over or behind a component to keep the components from wearing on each other (greasing) 青铜耐磨板(油润滑的) Casting An un-machined cast metal tread ring or Segment 铸件：未加工的金属花纹圈或花纹块铸件。 Centering Ring The ring mounted on the bottom press platen to locate the mold/ container concentrically to the press; also: "Press register" 定中环,也称“Press register” Clamp Rings The bladder clamping assembly 胶囊夹盘 Cone Ring The outer ring that transforms the axial movement of the press in a radial one of the segments; also: "Actuator ring", "Squeeze ring" (GT) 导环，也称"Actuator ring", "Squeeze ring" Conicity Difference between tread radius over the width 锥度 Container The mechanical parts that allow a segmented mold to operate; also: mechanism (GT) 模壳,也叫mechanism Container Cavity The space inside of the container that the mold fits into 模壳内腔：模壳内部放置模具的空间。 DD-Diameter Nominal diameter of a bead ring (EU) Also: "Heel diameter" (GT) 钢圈的公称直径, 也叫"Heel diameter" Decoupler Rib A narrow rib that runs circumferentially around the mold and is located near the shoulder area
大底模具技术术语中英文对照
LN3--PU/Phylon/Rubber Process Contents for these three sections of English Version PFC: ?Phylon Work Sheet PH数据表 ?Components Specification Sheet(Phylon) 部件明细单(Phylon)?Component Specification Sheet Set Up(Phylon) (此部分无中文) ?Phylon Midsole Specifications PH全插规格 ?Phylon Preform Specifications PH粗胚规格 ?Preform Drawing 粗胚图 ?Component Specification Sheet Set Up(PU) (此部分无中文) ?PU Midsole Specifications PU全插规格 ?PU Midsole Specifications II PU数据表 ?Components Specification Sheet(PU) 部件明细单(PU) ?PU Midsole Pouring Specification PU灌注明细 ?Outsole Color Schedule 本底颜色明细 ?Outsole Preform Specifications 本底粗胚规格 ?Outsole Pressing Process 本底压制流程 ?Outsole Degreasing Process 本底水洗流程 ********************************************************************* ΦPU Section ΦPU部分 ********************************************************************* air bag schedule 空气袋分段 specific instructions 特别说明 air bag diagram 空气袋图示 hardness(skin on) 硬度（带皮） density 密度 elongation 延伸率 tear 撕力 tensile 拉力 split tear 撕裂 painting 喷漆 MCS number 材料编号 mold release agent 脱模剂 polyurethane 聚安脂 polyester 聚脂 Density must be within NIKE spec and follow weight chart 密度必须符合NIKE要求及重量表 No dirty midsole sidewalls yellowing or poor cosmetics due to mold condition. 无因模具造成的边墙黄变及外观不良。 Correct molded or painted colors per NIKE confirmation. 根据NIKE的确认，成型材料及喷漆颜色正确。 Correct top/bottom edge trimming within 1mm width allowance. 正确修边上部及底部边缘，允许1mm余量。 No larger than 5mm diameter internal air voids.(checked by light table)
模具中英文对照表
landed plunger mold 有肩柱塞式模具burnishing die 挤光模 landed positive mold 有肩全压式模具button die 镶入式圆形凹模 loading shoe mold 料套式模具 center-gated mold 中心浇口式模具loose detail mold 活零件模具 chill mold 冷硬用铸模 loose mold 活动式模具 clod hobbing 冷挤压制模 louvering die 百叶窗冲切模composite dies 复合模具 manifold die 分歧管模具 counter punch 反凸模 modular mold 组合式模具 double stack mold 双层模具 multi-cavity mold 多模穴模具electroformed mold 电铸成形模 multi-gate mold 复式浇口模具expander die 扩径模 offswt bending die 双折冷弯模具extrusion die 挤出模
palletizing die 叠层模 family mold 反套制品模具 plaster mold 石膏模 blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具 fantail die 扇尾形模具 pressure die 压紧模 fishtail die 鱼尾形模具 profile die 轮廓模 flash mold 溢料式模具progressive die 顺序模 gypsum mold 石膏铸模 protable mold 手提式模具 hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模 punching die 落料模 lancing die 切口模 raising(embossing) 压花起伏成形re-entrant mold 倒角式模具
高中数学常用术语中英对照 mathematics
数学mathematics, maths(BrE), math(AmE) 公理axiom 定理theorem 计算calculation 运算operation 证明prove 假设hypothesis, hypotheses(pl.) 命题proposition 算术arithmetic 加plus(prep.), add(v.), addition(n.) 被加数augend, summand 加数addend 和sum 减minus(prep.), subtract(v.), subtraction(n.) 被减数minuend 减数subtrahend 差remainder 乘times(prep.), multiply(v.), multiplication(n.) 被乘数multiplicand, faciend 乘数multiplicator 积product 除divided by(prep.), divide(v.), division(n.) 被除数dividend 除数divisor 商quotient 等于equals, is equal to, is equivalent to 大于is greater than 小于is lesser than 大于等于is equal or greater than
小于等于is equal or lesser than 运算符operator 平均数mean 算术平均数arithmatic mean 几何平均数geometric mean n个数之积的n次方根倒数（reciprocal）x的倒数为1/x 有理数rational number 无理数irrational number 实数real number 虚数imaginary number 数字digit 数number 自然数natural number 整数integer 小数decimal 小数点decimal point 分数fraction 分子numerator 分母denominator 比ratio 正positive 负negative 零null, zero, nought, nil 十进制decimal system 二进制binary system 十六进制hexadecimal system 权weight, significance 进位carry 截尾truncation
自行车常用术语中英文对照
车种model 自行车 bicycle 折叠车 folding bicycle 避震车 suspension bicycle 城市车 city bicycle/CTB 山地车 mountain bicycle/MTB 跑车 racing bicycle 童车 children bicycle 速降车 down hill bicycle 登山越野车 trekking bicycle 普通越野车 cross country bicycle/XC BMX（bicycle Motocross) 自行车越野/自行车特技表演单轮车 unicycle 三轮车 tricycle 电动车 electric bicycle 滑板车 scooter 双轮双座自行车 tandem 计时赛车 time trial/ 旅游沙滩车 cruiser 场地车 track
车架组件 frame parts 车架 frame 上管 top tube(T/T) 中管 seat tube(S/T) 下管 down tube(D/T) 前叉 front fork 前叉肩盖 front fork crown 前叉竖管 front fork stem 车头组件 headsets 五通碗组件 bottom bracket parts 头管 head tube(H/T) 五通 bottom bracket 勾爪 dropout(END) 上叉 seat stay(S/S) 下叉 chain stay(C/S) 前叉端 fork end 座管 seat post 座管束子 seat post clamp 车把 handlebar 把立 stem
汽车电子技术常见术语中英文对照
汽车电子技术常见术语中英文对照(Ⅰ) 随着电子技术在汽车领域的广泛应用,出现了大量的专业术语,特别是出现了大量的英文专业缩略术语,参考了大量资料的基础上,经整理、分类将汽车电子技术中常见术语进行了中英文对照。为便于查找,将各种缩略语划为微电脑部分、车身底盘部分、发动机部分及其它部分等共4个部分(表1～表4)。 1微电脑部分常见术语(表1) 表1微电脑部分常见术语 英文缩略语中文全称英文全称 Ａ/Ｄ模拟/数字ＡｎａｌｏｇｔｏＤｉｇｉｔａｌ ＡＢ地址总线ＡｄｄｒｅｓｓＢｕｓ ＡＤＣ模拟/数字转换器 Analogto Digital Converter ＡＬＵ算术逻辑运算器 Arithmetic and Logic Unit ＣＢ控制总线ＣｏｎｔｒｏｌＢｕｓ ＣＤ光盘ＣｏｍｐａｃｔＤｉｓｋ ＣＤ-ＲＯＭ光盘ＣｏｍｐａｃｔＤｉｓｋＲＯＭ ＣＰＵ中央处理器 Central Processing Unit Ｄ/Ａ数字/模拟ＤｉｇｉｔａｌｔｏＡｎａｌｏｇ ＤＢ数据总线ＤａｔａＢｕｓ ＥＣＭ电子控制模块 Electronic Control Model ＥＣＵ电子控制器 Electronic Control Unit ＥＥＰＲＯＭ电可擦除只读存储器 Electronic Erasable Programmable ROM ＥＰＲＯＭ可擦可编程只读存储器 Erasable Programmable RO ＦＥＴ场效应管 Field Effect Transistor Ｉ/Ｏ输入/输出Ｉｎｐｕｔ/Ｏｕｔｐｕｔ ＩＣ集成电路ＩｎｔｅｇｒａｔｅｄＣｉｒｃｕｉｔ ＩＣ集中控制ＩｎｔｅｇｒａｔｅｄＣｏｎｔｒｏｌ ＬＳＩ大规模集成电路 Large Scale Integration ＭＯＳ金属氧化物半导体 Metal Oxide Semiconductor Ｐ-ＭＯＳＰ型ＭＯＳ Ｄ-ＭＯＳＤ型ＭＯＳ Ｃ-ＭＯＳＣ型ＭＯＳ ＰＣＵ泵控制单元ＰｕｍｐＣｏｎｔｒｏｌＵｎｉｔ ＰＲＯＭ可编程只读存储器ＰｒｏｇｒａｍｍａｂｌｅＲＯＭ ＲＡＭ随机存储器 Random Access Memory ＲＯＭ只读存储器ＲｅａｄＯｎｌｙＭｅｍｏｒｙ ＳＣＩ微型计算机接口 Small Computer Interface ＶＣＤ视频高密光盘ＶｉｓｕａｌＣｏｍｐａｃｔＤｉｓｋ ＶＣＵ车辆控制单元ＶｅｈｉｃｌｅＣｏｎｔｒｏｌＵｎｉｔ ＶＬＳＩ超大规模集成电路 Very Large Scale Integratioa 2车身底盘部分常见术语(表2)