模具专业术语
dowel pin 定位销
3 plate
3 plate 3 板模
a plate A板
accelerated EJ
accelerated EJ 加速顶出
Act. Press 实际射胶压力
air circuit threads 气路喉牙
air cylinder 气压行位
air poppets 气动阀
air vent 排气孔
Air 气顶
all cavities & cores to be marked for steel type and hardness 所有的前后模镶件需要标上材料和热处理硬度allen bolt 内六角螺钉
aluminum casting
angle ground
angle lifters 斜顶
angle pins 斜导注
angled lifters 斜顶
angular cam 弯销
angular ejector 斜针
angular pin 斜导柱
approval sheet
approved report 确认报告
approximate mold size 估计模胚尺寸
approximate tonnage 估计吨位
sprue bushing spherical radius
Are all items on design ballooned?
Are clotherspins shown?
Are construction dowels for plates shown if required?
Are construction dowels for plates shown if required?
Are hydraulic cylinders sufficient size?
Are insert pockets dimensioned ?
Are jiffy tites to customer standard?
Are lifter bushings adequate?
Are limit switches to customer's standard?
Are limit switchies shown?
Are locatin dowels dimensioned in mold ?
Are manifold lines shown in mold?
Are pockets for lifter slides OK?
Are protector pillars shown?
Are water line counter bores and taps to standard?
Are wire channels shown?
as needed 按需要
b plate B板
back plate 组装板
back pressure 背压
baffle 冷却棒
Baffles clearly identified and labeled ? Ball. Plungers 波子螺丝
band heater 电热环
barrel 料筒
bearing 轴承
bed die 下模,底模
bending 弯曲
bite 咬力
black spot 杂物不良
blade ejector 板顶针
blanking die 冲裁模
blast 喷沙
block ejector 顶块顶出
blocks 内模
bloe hole 气泡
blow molding 吹出成型
body lines
boost
bottom board 浇注底板
bottom clamp plate 底板
brone wear plate 青铜耐磨板
burn mark 烧焦痕
burr 披锋
cad-cam data supplied by
cam
cam as required 按要求设计行位cartridge heater 电热管
cav. Mark 型腔识别
cavity adaptor plate 固定侧安装板cavity cut in plate 前模原身出?cavity insert 型腔镶块
cavity inserted 前模镶件
cavity mumber 出模编号
cavity mumber 穴位数
cavity plate 模仁板
cavity side 前模侧
cavity stamping
cavity 模穴,模仁,模腔
cavity 前模
cell 气孔
center between KO holes 顶棍孔中心center pin 中心针
center sprue 中心唧嘴
center sprue 中心入水
center support 中心垫
chamfered and grinded 倒角和磨光大
clam pression
clamp plate 压板
clamp slots
clamp stroke 合模行程
clamping block 锁定块
clamping force used 注朔和吨位clamping force 夹紧力
clamping force 锁模力
clamping plate 模板
clamping 合模
closing angles 锁紧
closing sequence 合模次序
coil heater 电热线圈
coil spring 弹簧圈
cold runner 冷流道
cold slug well 冷料穴
components are DME/pcs
compound die 复合模
compound molding 复合成型compound molding 压缩成型compression spring 压缩弹簧
concept mold design 模具概念设计图纸conforms 一致
connecting box 接线盒
controller supplied by
cool runner system
cooling channel 冷却管
cooling circuit 冷却管道
cooling 冷却
cooling/heating cavities 冷却/加热前模cooling/heating cores 冷却/加热后模core cut in plate 后模原身出?
core inserts 后模镶件
core pin 型芯
core pin 型芯镶针
core side 后模侧
core 后模
crack 裂化
CSH. Screw 沉头螺丝
cushion 垫料
cycle 周期
cylinder on EJ plate 油压缸在顶针板上cylinder unit 气缸
cylinders on EJ Bar
damage 打痕
data type 数据类型
date insert 日期镶件
date mark 日期转印
dater 日期码
datum lines 基准线
datum plane 基准面
deburring 细加工
decompression
deformed / warpaged 变形
density 比重
detailed component drawings 详细零件图纸
die blocks
die closed
Die relief and vents shown and dimensioned ?
die slide 下模滑动装置
dimple gate 波纹式
direct gate 直接浇口
DME or equivalent DME 或相等料
DME 规格?
Do ejector pins miss water lines by 200?
Do rail screws miss water lines by 200?
Does cover or ejector block thickness have to be held ? Does each heating zone have a T/C shown?
Does K.O. pattern match press layout?
double ejection 二次顶出
dowel pin of mold leg
dowel pin 销针
Dowes hydraulic cylinder meet N.F.P. A. standards? draft angle 脱模斜度
draft 脱模角度
drag marks 拖花
driling 孔位加工
drill EJ hole 钻顶针孔
drill water core/cavity 钻运水孔
drop 支流道
duplicating casts by
dwell pressure 保压压力
E.J. sleeve 顶出杆
edge gate 侧水口
edge gate 侧浇口
edge tab 边水口
EDM cutting放电加工
EDM electrical discharge machining 电火花加工EDM machining 放点加工
EDM master 铜公
Ej bars 顶杆
Ej blades 扁顶针
Ej pin container plate
Ej pins 顶针
ejctor blade 扁顶针
ejection cavities 前模顶出
ejection cores 后模顶出
ejection force 顶出力
ejection half 顶出侧边
ejection mechanisam 顶出机械结构
ejection rod 顶杆数量
ejection stroke 顶出距离
ejection times 顶出次数
ejection type 出模形式
ejection 顶出
ejectionplate springs 顶针板弹簧
ejector guide pin 顶出导销
ejector guide pin 推板导注
ejector guide 顶出板导柱
ejector plate 顶针板
ejector retainer plate 面针板
ejector sleeve pin 司筒针
ejector sleeve 丝筒
ejector sleeve 推管
ejector stroke 顶出行程
ejectors not returned 顶针不回
Elec. Heaters 电热偶
electric leakage 漏电
Electrical connectors and t-couples to standard? electro plating 电镀加工
electrode 做电极
elongate spring 拉伸弹簧
engraving 雕刻加工
etching 表面蚀刻
even 平坦
expected cycle time 预计成型周期
export wooden crate 出口木箱
Eye bolt holes size and location dimensioned ? eye bolts 吊模孔
eyebolt holes 吊圈,吊模孔
fan gate 扇形水口
finish cavities 抛光前模
first shot 第一次试模
fitting and assembling 配模和组立
fitting 配模
fittings 沉孔
fix die, cover die 定模
fixed clamping plate 定模底板
fixed side
fixed transfer mold 固定式传递模
flash chrome 镀铬
flash 披锋
flexture
floating plate
flow control bubblers
flow mark 喷流痕
forming die 成型模
full round 整圆
full shot 充填
galling 擦伤
gas trapped 困气
gas vents 排气槽
gate inserts 镶件入水
gate 水口
gear rack 齿条
gear wheel 齿轮
gibs and wear plates 压条和硬片
gloss not enough 光泽不够
good polish 有光泽
grinding 磨床加工
grip holder 夹头
guarantee shot 保证产量
guarantee 保证产期
guide bush导柱套
guide ejections 顶出导向
guide pin 导柱
guide pins 边钉
guide rails 滑块压板
guided ejection 顶出导向
guided ejection 中托司
hair flash 胶丝
half round 半圆
hand loaded inserts 手动送镶件hardening 热处理
Hasco
heal block 锁定块
heat pipe 加热管
heat treatment procejure 热处理规范heater connectors supplied by
heater controller / connectors 热嘴连接件heaters
heel locking block 铲鸡
high polish 高度抛光
hold on 保压
hose nipple 水嘴
hot runner manifold 热流道
hot runner mold 热流道模
hot runner 热流道
hot sprue bushing 热唧嘴
hot sprue bushing/tip 热唧嘴
hot sprue 热水口
hot stamping 热压
hot tip 热嘴
hydraulic cylinder 液压缸
hydraulic slider 液压行位
hydraulic unit 油唧
hydraulic/pneumatic cylinders
injection forming 注射成型
injection molding 射出成型
injection nozzle 射出喷嘴
injection piston 压射冲头
injection plunger 射出柱塞
injection press of m/c 射胶压力
injection 射胶
insert pin 嵌件销
Insert water dimensioned from edge of insert? insert welding 焊接
inserted 镶件
insets molded into part 撬模坑
inspection report 测量报告
insulated runner mold 绝热流道模
insulator plates 隔热板
inter lock 定位机构
Is cavity for plugs and wires adequate?
Is clearance counter bore for sleeve ext. OK? Is grease for guided ejection shown if required? Is hydraulic schematic palque shown?
Is hydraulic schematic shown?
Is lock angle relationship to cam pin correct?
Is manifold to customer's standard?
Is mounting for wear plates shown?
Is mounting for wear plates shown?
Is plug mounting plate diagarm shown?
Is timing of cam pin correct/
Is water line plaque shown?
kick off 标准
KO extensions KO 连接件
KO holes in BCP 顶棍孔
KO holes KO 孔
KO holes quantity顶棍孔数量
KO plattern KO 排位
Lifter water dimensioned from edge of lifter? lifter 斜顶
lifters as required 按要求做斜顶
lifting hole 吊模孔
linework
list of components 零件表
locating ring 定位圈
location 定位
lower support 下压垫
machine nozzle radius 啤机射嘴半径
machine type 注朔机型号
machining marks 加工痕迹
manifold block 流道板
manifold 热流板
manifold 热流道结构
marking 字嘪
master sixze provided
material & heat treat certificates 材料和热处理证书material of cavities 前模料
material of cores 后模料
material shrinkage 材料缩水率
mech. Slider 机械行位
mechanical slider 机械滑块
medium polish 中度抛光
micro switchers supplied by
microswitches 微动开关
milling machining 铣床加工
mold base steel 模胚钢材
mold base 模胚
mold closing 闭模速度
mold compnents 模具配件
mold drawings w/component list 模具图和明细烂mold flow analysis by
mold layout 模具排位
mold leg
mold opening force 开模力
mold plaque
mold plate 模板
mold shipping 走模
mold try-out 试模
molded in inserts 带插件成型
molded part inspection by
mould base steel 模架材料
mould base 模架
mould fastened, locked and stable 模具锁死
mould height 模具厚度
mould life expectancy 模具寿命
mould max. size 最大模具尺寸
mould trial report 试模报告
moulding information 模具资料
moulding machine press/type 啤机种类
moulding material type 啤朔材料
moulding status 成型方式
moving clamping plate 动模底板
moving die, ejector die 动模
moving side
MUD or equivalent MUD 或相等料
multi-cavity mold must have cavity identified marks 多腔数模具要有cavity的号码national
need a valve or air assistance to break 需要吹气辅助顶出
nip 夹沟
nitriding氮化处理
no cav. Number 无模腔编号
no ejection hole tapped 顶棍板无塔牙
no return spring 无回针弹弓
No. of cavity穴数
No. of cavity穴数
not dries enough 干燥不足
nozzle miss fitting 卷唧嘴漏胶
nozzle recess
nozzle 唧嘴
o ring 密封圈
offset leader pin
oil dirt 油污点
oil 运油
open nozzle 开式注嘴
opening stroke 开模行程
open开模
optical polish 电镀抛光
outer slide 外滑块
PA6 + 33% GF 33% glass-filled nylon
part & runner 产品和水口
part drawings 产品图纸
part hanged 挂成品
part weight 产品重量
parting line locks 分模线锁件
parting line 分模线
parting lock set 拉勾
parting lock 分模定位锁
perpendicular
pin gate 点水口
pin pint gate mold plate 细水口模胚
pin point gate 针孔形水口,细水口
pin point 点水口
PL 面固定?
plastic material & mold shrink 朔胶材料和收缩率
plasticizing capacity 朔化能力
plasticizing 朔化
plate ejector顶板顶出
plate travelling 模板移动
platen dimensions 载模板尺寸
platen drawing avaliable? 有无啤机平面图plating 电镀
polish cores 抛光后模
polishing 省模加工
post gate
pre=assembly of mould 合模前检查preliminary mold layout 初步设计
pre-shipment of mould 发模具前
Press ite bars shown in phantom?
press make & size 啤机类型和大小
primary cavity 前模镶件
primary core 后模镶件
process report 进度报告
process report 试模报告
procom
production cycle 注朔周期
progressive
protective grease on the core and cavity 打防锈油proximitly switches
pry bar slots 顶出杆攻牙
pull bolt 小拉杆
puller pin 勾针
puller plate 拉板
QC coupler required
QC manifold required
Qre threaded pull-backs shown if required? raised 高出
rear 尾部
recessed 下沉
recycle insert 环抱镶件
recycle marking 环抱标
regrind 水口料
remains 剩余料
removable inserts (hardened) 硬化的互换镶件retrial of the tools 重新试模
return pin 回针
Rev. ejection 反顶出
rib machining 骨位加工
ring gate 环形水口
robot 自动机械手
rough milling CNC cutting CNC 粗加工
rough polishing 粗抛光
runner / gate blocks 水口/浇口一起
runner hanged 挂水口
runner less mold 无流道模
runner lock pin 水口针
runner plate 流道板
runner stripper plate 第二固定板
runner 流道
runner 水口
rust 锈蚀
S.S. 不锈钢
safety strap 安全板
Safety straps shown in plan views and sec. Views? safty back angle 安全的复位角度
safty loop 保险圈
sample material 样件胶料
scrap slot
scratch 拉伤
scratches 伤痕
sharp pt.利角
SHC. Screw杯头螺丝
shim
ship material 寄料
short moulding 短射
short shot 充填不良
short shot 走水不齐
shot cylinder 压射缸
shot volume 注射量
shot weight 射胶重量
shot weight 射胶重量
shoulder guide bush 托司
SHS. Screw 山打螺丝
shut off 封胶
side core movement 行位运动
side cores 行位
side gate mold base 大水口模胚
side gate 侧浇口
side gate 侧水口
side interlocks 边锁
side locks 边锁
silk screen 丝印
silver line 银条状
single cavity mold 单腔模具
sink mark 缩水
six hot drops 6点热流道
slant ejector 斜顶
sleeve ejector 司筒顶出
sleeve 司筒
slide action 斜顶式滑块
slide return spring 行位回复弹簧
Slide water dimensioned from edge of slide? slider not returned 行位不回
slider 滑块板
slider 行位
spacer block 方铁
SPE/SPI ?
special features 特殊要求
spraying 喷油
spring activated
spring activated 弹簧动作
spring loaded EJ Bar
spring return 回位弹弓
sprue bush , sprue bushing 浇口套
sprue bush depth 唧嘴长度
sprue bush radius 唧嘴球径
sprue bush 机嘴套
Sprue bushing and sphere. Rad. Fit machine? sprue bushing 唧嘴
Sprue puller pin shown and dimensioned ? sprue 水口
sprue直流道
standard electrodes 标准铜公
steel crate 包装箱
steel layout 内模尺寸
sticking cavity 粘前模
sticking core 粘后模
sticking sprue 粘水口
sticking 离形不良
stock temp.料温
stop bolt 定位杆
stop disc 限位钉
stopper block 限位板
stopper bolt 水口螺丝
stopper pin 定距拉杆
straight guide bush 直司
stripper block 推方
stripper pillar 推销
stripper plate 水口板
stripper plate 推板
sub gate in pin 顶针潜入
sub to E.J. pin 潜水口到顶针
subarine gate 潜水口
submarine gate 潜水口
suck back 倒索
supplied by mold maker 模具厂要提供的support pillar 支撑柱
support pin 撑头
support pin 拉杆
support plate 托板
support spacer 方铁
surface hardness 表面处理
switch position 转换位置
tapered interlocks 锥度互锁
tappered interlock 爹把边钉
TBD?
teeming 浇注
temp. contr.unit 调温机
texture 皮纹
texture 咬花, 蚀纹
the back clampin plate
the calmpin slot
the in-out marking of cooling system 冷却系统的出入标记themo plastic 热可朔性
themoset injection 热固性注射模具
thermo set 热硬化性
thermocouple connectors
thermoplastic injection
thermoplastic injection 热朔性注射模具
thermoset injection 热固性注射模具
threaded EJ bar
three plate type mold plate 简化形细水口模胚
tia bar max distance 拉杆距离
tie bar clearance
tie bar spacing 啤机距离
tie bars 导注
tie rods 拉杆
title block 标题拦
tolerance of fit 配合公差
tool trials 试模
top clamp plate 面板
top of mould 俯视图
total mumber of cavities 模穴总数量
transducer
trapezoid 梯形
trapezoid 梯形
trial duration 总实模时间
try machine 试模机
tube heater 电热筒
tubular heater 电热线
tunnel (sub-gate) 潜水口
type of gate 入水方式
type of gating defined
type of injection gate 水口类型
type of runner 水口类型
under cut 倒扣
uneven gloss 光泽不均
unscrewing (auto) 自动脱螺纹
unscrewing 脱螺纹
upper support 上压板
use water -proof plastic sheet 用朔料防水薄膜封死UV test 紫外光
valve gate 针阀水口
valve nozzle 阀式注嘴
velosity 射胶速度
vent 通气孔
venting 排气
virgin 原料
warm runner mold 温流道模
warpage 变形
water cooling threads 运水喉牙
water cooling 水冷却系统
water fittings 运水
water leakage 漏水
water lines connector type 水平线连接器
water threads 运水塞
waterline not marked 无运水字嘪
wear plates 滑块固定板
wear plates 耐磨板
weld line 夹水纹
white mark 顶白
wire cutting 线切割加工
with antirust grease oil 有防锈油
work hardening 加工硬化
work lines
zero corners
zero side
zhinc die cast
晒纹?
水路规格? PT? NPT?
外观无段差?
core plate 下模模板
backhaul switch 回程开关
U-coupling 斜顶导行块
insulate plate 隔热板
plug 水嘴
interlock 方形辅助器
top clamp plate 上码模板
bottom clamp plate 下码模板
lifting strap plate 吊模板
space block 限位块
puller pin 拉料销
slide guide plate 压块
wear block 耐磨块
angle pin 写导柱
flat pin 扁顶针
core plate 下模镶件
cavity plate 上模镶件
sub-insert 小镶件
core sub-insert 下模小镶件cavity sub-insert 上模小镶件slide insert 行位镶件
gib 压条
jaw 压紧块(铲机)
wedge 斜机
S.H.C.S. 杯头螺丝
plate 压条
coupling 管接头
lock plate 锁模块
side lock 平行锁
wedge wear plate 油板
angle pin 斜边
KO rod 顶棍
support pillar 模顶
guide block 青铜
T-gib T型导槽
side core starting block 行位压条mold lock block 锁模块
ejector clamping plate 顶针码板ejector guide pin 中管边
dowel pin 顶位销
side cotter block 铲机
runner bar水口铁
upper runner bar 上模水口铁lower runner bar 下模水口铁sprue puller pin 水口勾针
side lock 直身锁
inter lock 斜度锁
safety bar 锁模板
plug 喉塞
baffle 隔水板
ball-catch 波子螺丝thermocpuple 探热针
stripper bolt 限位螺丝
cover plate 盖板
hydraulic cylinder 油唧
leader pin 导柱
bushing 导套
stripper plate 热板
ejector retainer plate 顶针底板
retainer plate 垫板
core pin 模芯针
stop pin 拉圾钉
shoulder ejector pin 有托顶针
guide ejection bushing 顶针板导套
guide ejcetion leader pin 针板导柱
extension nozzle bushing 三板模延伸式唧嘴
runner stripper plate bushing 水口板导套
locating ring 定位圈(法兰)
dowel pin 定位销(管钉)
tubular dowel 管状管钉
safety hoist ring 吊环
dating insert 日期印
recycling insert 环保印
air poppet valve 气顶
runner shut-off insert 截水口镶件
early ejector return 早回
shut off 摖伤
stress mark 顶白
filling uneven 走水不平均
short shot 走不齐
air trapping 困气
tairipro pp resin consolidated property dat sheet 台化聚丙烯朔胶粒物性总表tensile strength at yield 降伏点抗张强度
tensile elongation at break 断裂点延伸率
flexural modules 弯曲模数
izod impact strength 冲击强度
heat deflection temperature 热变形强度
molding shrinkage 收缩率
specific gravity 比重
FDA compliance
flat yarn 扁沙级
homo=polymer 单聚物
multi-filament 纤维级
random copolymer 随意共聚物
extrusion & blow molding 挤出吹制级
impact copolymer 耐冲击共聚合物
general pupose 通用级