焊接专业术语
激光切割laser cutting(LC); laser beam cutting
电子束切割electron beam cutting
喷气激光切割gas jet laser cutting
碳弧切割carbon arc cutting
水下切割underwater cutting
喷水式水下电弧切割waterjet method underwater arc cutting
氧矛切割oxygen lancing; oxygen lance cutting 溶剂氧切割powder lancing
手工气割manual oxygen cutting
自动气割automatic oxygen cutting
仿形切割shape cutting
数控切割NC (numerical-control) cutting
快速切割high-speed cutting
垂直切割square cut
叠板切割stack cutting
坡口切割beveling; bevel cutting
碳弧气割carbon arc air gouging
火焰气刨flame gouging
火焰表面清理scarfing
氧熔剂表面修整powder washing
预热火焰preheat flame
预热氧preheat oxygen
切割氧cutting oxygen/ cutting stream
切割速度cutting speed
切割线lone of cut/ cut line
切割面face of cut/ cut face
切口kerf
切口上缘cutting shoulder
切口宽度kerf width
后拖量drag
切割面平面度evenness of cutting surface/ planeness of cutting surface
割纹深度depth of cutting veins/ stria depth
切割面质量quality of cut face
上缘熔化度shoulder meltability/ melting degree of shoulder
切口角kerf angle
缺口notch
挂渣adhering slag
结瘤dross
割炬cutting torch/ cutting blowpipe/ oxygen-fuel gas cutting torch
割枪cutting gun 割嘴cutting nozzle/ cutting tip
快速割嘴divergent nozzle/ high-speed nozzle
表面割炬gouging blowpipe
水下割炬under-water cutting blowpipe
水下割条electrode for under-water cutting
粉剂罐powder dispenser
数控切割机NC cutting machine
门式切割机flame planer
光电跟踪切割机photo-electric tracing cutting
火焰切管机pipe flame cutting machine
磁轮式气割机gas cutting machine with magnetic wheels
焊接结构welded structure/ welded construction 焊件weldment
焊接部件weld assembly
组装件built-up member
接头设计joint design
焊接应力welding stress
焊接瞬时应力transient welding stress
焊接残余应力welding residual stress
热应力thermal stress
收缩应力contraction stress
局部应力local stress
拘束应力constraint stress
固有应力inherent stress
固有应变区inherent strain zone
残余应力测定residual stress analysis
逐层切割法Sach’s method
X射线衍射法X-ray stress analysis
小孔释放法Mathar method
固有应变法inherent strain method
消除应力stress relieving
局部消除应力local stress relieving
应力重分布stress redistribution
退火消除应力stress relieving by annealing
温差拉伸消除应力low temperature stress relieving
机械拉伸消除应力mechanical stress relieving
应力松弛stress relaxation
焊接变形welding deformation
焊接残余变形welding residual deformation
局部变形local deformation
角变形angular distortion
自由变形free deformation
收缩变形contraction deformation
错边变形mismatching deformation
挠曲变形deflection deformation
波浪变形wave-like deformation
火焰矫正flame straightening
反变形backward deformation
焊接力学welding mechanics
断裂力学fracture mechanics
弹塑性断裂变形elasto-plastic fracture mechanics 线弹性断裂力学linear elastic fracture mechanics 延性断裂ductile fracture
脆性断裂brittle fracture
应力腐蚀开裂stress corrosion cracking
热应变脆化hot straining embrittlement
临界裂纹尺寸critical crack size
裂纹扩展速率crack propagation rate
裂纹张开位移（COD）crack opening displacement 拘束度restraint intensity
拘束系数restraint coefficient
应变速率strain rate
断裂韧度fracture toughness
应力强度因子stress intensity factor
临界应力强度因子critical stress intensity factors 应力腐蚀临界应力强度因子critical stress intensity factor of stress corrosion cracking
J积分J-integration
罗伯逊止裂试验Robertson crack arrest test ESSO试验ESSO test
双重拉伸试验doucle tension test
韦尔斯宽板拉伸试验Well’s wide plate test
帕瑞斯公式Paris formula
断裂分析图fracture analysis diagram
焊接车间welding shop
焊接工作间welding booth
焊接工位welding post/ welding station
焊接环境welding surroundings
焊工welder
电焊工manual arc welder
气焊工gas welder
焊接检验员weld inspector
焊工培训welders training
焊工模拟训练器trainer of synthetic weld
焊工考试welder qualification test
焊工合格证welder qualification/ welder qualified certification
钢板预处理steel plate pretreatment
喷沙sand blast
喷丸shot blast
矫正straighten
开坡口bevelling (of the edge)/ chanfering
装配assembly/ fitting
安装erect
刚性固定rigid fixing
装配焊接顺序sequence of fitting and welding 焊接工艺评定welding procedure qualification 焊接工艺规程welding procedure specification 焊接工艺试验welding procedure test
焊接工艺卡welding procedure card
工序operational sequence
焊接材料消耗定额welding consumables quota 焊接工时定额welder-hour quota
清渣slag removal
清根back gouging/ back chipping
锤击peening
返修次数number of rewelding
焊接工作台welding bench
装焊平台welding platen
电磁平台electromagnetic platen
焊接翻转机welding tilter
焊接回转台floor turnable positioner
焊接变位机positioner
焊接滚轮架turning rolls
焊接操作机manpulator
焊工升降台welder’s lifting platform
焊接夹具welding jig/ fixture
磁力夹紧器magnetic jig
螺旋推撑器screw operated tensioning unit
焊丝盘绕机welding wire coiler
焊条压涂机welding electrode extrusion press 红外线加热器infra-red heater
干燥箱dryer
焊条保温筒thermostat for electrode
流量计flow meter
CO2预热器CO2 heater
CO2干燥器CO2 desiccator
焊接电缆welding cable
电缆夹头welding connector
地线earth lead
地线夹头earth clamp
焊接参数记录仪welding parameter recorder
焊缝检测规weld gauge
喷嘴通针tip cleaner
测温笔tempil stick
敲渣锤chipping hammer
焊接衬垫backing/ welding backing
保留垫板fusible backing/ permanent backing
临时垫板temporary backing
焊剂垫flux backing
惰性气体衬垫inert-gas backing
引弧板run-on tab/ end tab/ starting weld tab
引出板run-off tab/ end tab
定位板strong-back
加强勒stiffener
嵌条insert
套环ferrule
面罩helmet
滤光镜片filter glass/ welding glass
防护镜片cover glass/ plain glass
气焊眼镜welding goggles
焊接机器人welding robot
点焊机器人spot welding robot
弧焊机器人arc welding robot
切割机器人cutting robot
焊接机器人生产线robot line for welding
焊接机器人工作站welding robot station
机器人运动自由degree of free for robot
机器人工作空间robot working space
轨迹重复精度path repeatability
点位重复精度PTP repeatability
焊接专家系统welding expert system
焊接机器人示数welding robot play back
焊接图象识别pattern recognition for welding
焊接图象处理welding image processing
计算机辅助焊接工艺设计computer-aided welding process programming (CAWPP)
计算机辅助焊接结构设计computer-aided design for welding structure
焊接烟尘weld fume
焊接发尘量total amount of fumes
焊接烟尘浓度weld fume concentration
焊接烟尘容限浓度threshold limit values of weld fume (TLV) 焊接发尘速率weld fume emission rate
焊接有害气体welding toxic gases/ weld harmful gases
标定卫生空气需要量nominal hygienic air requirement
焊工尘肺pheumocomsis of welder
焊工锰中毒chronic occupational manganese poisoning of welder
焊工氟中毒fluorosis of welder
焊工金属烟热metal fume fever of welder
电光性眼炎eye-flash (arc eye)
电光性皮炎electro-photo dermatitis
电弧紫外线灼伤ultraviolet ray burn
防电击装置voltage reducing device
除尘装置dust collection device
焊工手套welding gloves
护脚welding spats
防护鞋shielding shoes
焊接欠缺welding imperfection
焊接缺陷weld defect
气孔blowhole/ gas pore
针尖状气孔pinhole
密集气孔porosity
条虫状气孔wormhole
裂纹crack
表面裂纹surface crack
咬边undercut
焊瘤overlap
凹坑pit
烧穿burn through
塌陷excessive penetration
未焊透incomplete penetration/ lack of penetration 未熔合lack of fusion/ incomplete fusion
未焊满incompletely filled weld
根部凹陷root concavity
电弧擦伤arc scratch
夹渣slag inclusion
夹杂物inclusion
夹钨tungsten inclusion
白点fish eye/ flake
错边misalignment/ dislocation
试件test piece
试样test specimen
无损检验nondestructive test
破坏检验destructive test
外观检查visual examination
超声波探伤ultrasonic inspection
直射法超声波探伤straight beam method
斜射法超声波探伤angle beam method
液浸法超声波探伤immersion method
射线探伤radiographic inspection/ radiography
X射线探伤X-ray radiographic inspection
γ射线探伤gamma-ray inspection
X射线工业电视探伤X-ray industrial television inspection
磁粉探伤magnetic particle inspection
电磁探伤electromagnetic inspection/ eddy current test
探伤灵敏度flaw detection sensitivity
渗透探伤penetration inspection
荧光探伤flurescent penetrant inspection
着色探伤dye penetrant inspection
密封性检验leak test
气密性检验air tight test
枕形气密检验pillow test
耐压检验pressure test
水压检验hydraulic test
气压检验pneumatic test
液晶检验liquid crystal test
声发射检测acoustic emission testing
面弯试验face bend testing
背弯试验root bend test
侧弯试验side bend test
横弯试验horizontal bend test
纵弯试验axial bend test
压扁试验squeezing test
音响专业术语中英对照
专业音频术语中英文对照 A ＡAC ａutomａtiｃ ampltiｕdｅ control 自动幅度控制 AＢ AB制立体声录音法?Aｂeyaｎｃd 暂停,潜态 A-B repeat A-B重复?ABS absolｕte 绝对得,完全得，绝对时间 AＢＳaｍerican burｅａｕ oｆｓtanda rd 美国标准局?ABＳＳ auｔｏｂlａnk seｃrion ｓｃanning 自动磁带空白部分扫描Ａbsｔi mｅ绝对运行时间?A、ＤEＦ audiｏ dｅfeａｔ音频降噪,噪声抑制,伴音静噪 ADJ ａdj eｃｔｉve 附属得,附件?AＤＪ Aｄjust 调节 ＡDJ ａcｏｕｓｔｉｃｄｅlay lｉnｅ声延迟线 Admiｓsiｏn 允许进入,供给 ADP acouｓｔiｃｄaｔa ｐroceｓsoｒ音响数据处理机 ＡＤP(T) adaptｅr 延配器，转接器ＡDRES autｏmatｉｃｄynamic ranｇｅ ｅxpansion systｅm?动态范围扩展系统 A ＤRM ａnａlｏg tｏdigｉtal remastｅr 模拟录音、数字处理数码唱盘 ADS ａudio distribution system 音频分配系统 A、DUB aｕｄio dｕbbiｎｇ配音,音频复制,后期录音 AＤV ａdvance 送入，提升,前置量?ADV adｖersuｍ对抗 ADＶ advance r 相位超前补偿器?Ａｄvｅｎｔuｒｅ惊险效果 AE audio erasing 音频(声音)擦除 AE auxｉｌiａry eqｕipｍeｎt 辅助设备Aerｉａｌ天线 ＡＥＳaudio engineeｒing soｃieｔｙ美国声频工程协会ＡF audｉo fｉdelity 音频保真度?AF audio frｅquencｙ音频频率 AFC aｃtive fieｌd conｔrｏｌ自动频率控制?AＦC automatiｃfrｅquenｃｙ coｎtｒol 声场控制 Ａffricaｔe 塞擦音?AＦL ａside ｆａde lｉsten 衰减后(推子后)监听 A-fadｅr 音频衰减 ＡFM advancｅ freｑuency moｄulａtion 高级调频 AFS acoｕstｉｃ feedｂａｃｋ sｐea ｋer 声反馈扬声器 AFＴ automaｔｉc fiｎｅ tuning 自动微调 AＦＴAＡS advancｅｄｆast ｔime aｃousti ｃaｎaｌｙｓｉs ｓysteｍ?高级快速音响分析系统 Afｔer 转移部分文件 Aftergloｗ余辉，夕照时分音响效果 Agａin st 以……为背景 AGC ａｕtomａtic gaｉn contrｏl 自动增益控制AHＤaudｉｏhigｈ densｉtｙ音频高密度唱片系统 AI aｄvanced intｅgrateｄ预汇流ＡI amplｉfier inｐｕt 放大器输入 AI artificｉaｌ intellｉｇence 人工智能AI azｉmuｔh iｎdi cator 方位指示器 A－IN 音频输入 A－INSEL aｕｄｉo ｉnput sｅleｃtiｏn 音频输入选择 Alarm 警报器 ALC ａutomatic level cｏntｒoｌ自动电平控制?AＬC autｏmａtic lｏａd ｃontroｌ自动负载控制
常用焊接英语词汇大全
常用焊接英语词汇大全 焊接机器人welding robot 点焊机器人spot welding robot 弧焊机器人arc welding robot 切割机器人cutting robot 焊接机器人生产线robot line for welding 焊接机器人工作站welding robot station 机器人运动自由degree of free for robot 机器人工作空间robot working space 波峰钎焊flow soldering/ wave soldering 分级钎焊step brazing/ step soldering 不等间隙钎焊brazing with the unparalleled clearance 红外线钎焊infra-red brazing (soldering) 光束钎焊light soldering (brazing) 激光钎焊laser brazing (soldering) 电子束钎焊electron beam brazing 钎接焊braze-welding 钎料brazing filler metal/ solder 硬钎料brazing filler metal 软钎料solder (m) 自钎剂钎料self-fluxing brazing alloy/ self-fluxing filler metal 活性钎料active filler metal/ active metal brazing alloy 成形钎料preformed filler metal/ solder preform 非晶态钎料amorphous filler metal 粉状钎料powdered filler metal 钎料膏braze cream/ braze paste/ solder cream/ solder paste 药皮钎料flux coated brazing(soldering)rod 层状钎料sandwich filler metal 药芯钎料丝flux-cored colder wire 敷钎料板clad brazing sheet 钎剂brazing flux; soldering flux 气体钎剂gas flux 反应钎剂reaction flux 松香钎剂colophony flux; rosin flux 钎剂膏flux paste 阻流剂stopping-off agent 钎剂活性flux activity 钎剂活性温度范围activation temperature range of flux 钎剂热稳定性thermal stability of flux 钎焊过程brazing (soldering) process 钎焊操作brazing (soldering) operation
焊接术语翻译
焊接术语翻译 喇叭形坡口flare groove 锁底坡口single bevel groove with backing locked 坡形板边tapered edge 焊缝weld 接逢seam 焊缝符号welding symbol 焊缝金属weld metal 填充金属filler metal 熔敷金属deposited metal 焊缝表面weld face/ face of weld 焊缝背面back of weld 焊缝轴线axis of weld 焊缝尺寸size of weld 焊缝宽度weld width/ width of weld 焊缝长度weld length/ length of weld 焊缝有效长度effective length of weld 焊缝厚度throat depth/ throat thickness 焊缝计算厚度theoretical throat 焊缝实际厚度actual throat 熔深penetration/ depth of penetration 焊缝成形appearance of weld 焊缝成形系数form factor of weld 余高reinforcement/ excess weld metal 背面余高root reinforcement 削平焊缝flush weld/ weld machined flush 对接焊缝butt weld 角焊缝fillet 焊脚leg/ fillet weld leg 角焊缝断面形状profile of fillet weld 平形角焊缝flat fillet 凸形角焊缝convex fillet weld 凹形角焊缝concave fillet weld 角焊缝凹度concavity 侧面角焊缝side fillet weld/ fillet weld in parallel shear 正面角焊缝front fillet weld/ fillet weld in normal shear 立角焊缝fillet weld in the vertical position 横角焊缝fillet weld in the horizontal position 平角焊缝fillet weld in the flat position 斜角焊缝oblique fillet weld 连续焊缝continuous weld 断续焊缝intermittent weld 连续角焊缝continuous fillet weld 断续角焊缝intermittent fillet weld 交错断续角焊缝staggered intermittent fillet weld 并列断续角焊缝chain intermittent fillet weld 端接焊缝edge weld 卷边焊缝flanged edge weld 塞焊焊缝plug weld 纵向焊缝longitudinal weld 横向焊缝transverse weld 环行焊缝girth weld/ circumferential weld 螺旋形焊缝spiral weld/ helical weld 密封焊缝seal weld 承载焊缝strength weld 联系焊缝connective weld 定位焊缝tack weld 焊道bead/ run/ pass 焊波ripple 焊根weld root/ root of weld 焊趾weld toe/ toe 封底焊道sealing run (after making main weld)/ b ack weld 打底焊道backing weld (before making main weld) / back weld 根部焊道root pass/ root run 填充焊道filling bead 盖面焊道cosmetic bead/ cover pass 回火焊道temper bead/ annealing bead 熔透焊道penetration bead 焊层layer 焊接接头welded joint 接头形状joint geometry 等强匹配接头equal matching weld joint 低强匹配接头undermatching weld joint 超强匹配接头overmatching weld joint 接头根部root of joint 对接接头butt joint I形对接接头square butt joint V形对接接头single V butt joint U形对接接头single U butt joint J形坡口接头single J butt joint 双V形对接接头double V butt joint 双单边V形对接接头double bevel butt joint/ K gro ove butt joint 带钝边U形对接接头double U butt joint
焊接专业术语中英文对照整理
机械——焊接专业术语中英文对照 （郭运）整理 1Single 单面的 2V—groove V型坡口 3Joint 焊接接头 4Edges overlap 接头形式 5Butt 对接 6T T型焊接 7Fillet 角焊缝 8Edge 端接 9Corner 角接 10Radius 半径 11Joint root 焊接根部 12Bevel angle 削边角度 13Groove angle 坡口角度 14Root face 根部钝边 15Groove face 坡口面 16Plug weld 塞焊 17Spot weld 点焊 18Seam weld 缝焊 19Slot weld 槽焊 20Double—flare—bevel—groove K型坡口焊缝
21Single—flare—V 单面V型22Edge flange 翻边端接 23Corner flange 卷边端接 24Flange weld 卷边焊缝25Flare weld 扩口焊缝26Fillet weld 角焊缝 27Slot weld 槽焊缝 28Spot weld 点焊缝 29Surfacing weld 堆焊焊缝30Melt—through weld 熔透焊缝31Backing weld 打底焊缝32Back weld 背面焊缝33Root weld 根部焊缝34Crown weld 隆起部分35Weld reinforcement 焊缝加强36Weld face 焊缝表面37Cap pass 盖面焊道38Weld edge 焊缝边缘39Leg 焊脚 40Toe 焊趾 41Buildup 堆焊 42Weld reinforcement 焊缝加强高
常用焊接术语中英文对照
常用焊接术语中英文对照 焊接Welding 10.1 焊接种类Varieties of Welding 电弧焊arc welding 电熔焊electric fusion welding (EFW) 气熔焊fusion gas welding (FGW) 电阻焊electric resistance welding (ERW) 有保护的金属电弧焊shielded metal arc welding (SMAW) 手工或自动隋性气体保护钨极电弧焊manual and automatic inert gas tungsten arc welding (GTAW) 自动埋弧焊automatic submerged arc welding 金属极隋性气体保护电弧焊gas metal arc weiding (GMAW) 氩弧焊argon-arc welding， 气体保护电弧焊gas-shielded arc welding 气焊gas welding; flame welding 等离子焊plasma welding 硬钎焊braze welding 电渣焊electroslag welding 爆炸焊explosive welding 10.2 焊接形式Type of Welding 角焊fillet welding 间断焊intermittent welding 点焊spot welding 对焊butt welding 搭焊lap welding 塞焊plug welding 珠焊bead welding 槽焊slot welding 堆焊build up welding 垫板焊backing weld 坡口groove V形坡口V groove 单面U形坡口single U groove K形坡口double bevel groove X形坡口double V groove 双面U形坡口double U groove U-V组合坡口combination U and V groove 根部间隙root gap 焊接符号symbol of weld 错边量alignment tolerance
飞机专业术语(英汉对照)
1、the airframe 机身,结构 2、The front (fore) part 前部 3、The rear (aft) part 后部 4、port 左旋(舵) 5、starboard 右旋(舵) 6、the inboard engine or inboards 内侧发动机 7、the outboard engine or outboards 外侧发动机 8、the nose 机头 9、the belly 腹部 10、the skin 蒙皮 11、the windscreen or windshield 风挡 12、the wing 机翼 13、the trailing edge 机翼后缘 14、the leading edge 机翼前缘 15、the wing tip 翼尖 16、the control surface 操纵面 17、ailerons 副翼 18、flaps (inboard flap,outboard flap,leading edge flaps) 襟翼（内侧襟翼，外侧襟翼，前缘缝翼） 19、spoilers (inboard\outboard spoiler)(spoiler down\up) 阻力板，扰流板（内、外侧扰流板）（扰流板放下、打开） 20、slats 缝翼 21、elevators (elevator control tab) 升降舵（升降舵操纵片） 22、rudder (rudder control tab) 方向舵（方向舵操纵片）
23、flap angle 襟翼角 24、flap setting 襟翼调整 25、the full flap position 全襟翼位置 26、a flapless landing 无襟翼着陆 27、the landing gear 起落架 28、stabilizer 安定面 29、the nose wheel 前轮 30、gear locked 起落架锁定 31、the wheel well 起落架舱 32、the wheel door 起落架舱门 33、a tyre 轮胎 34、to burst 爆破 35、a deflated tyre 放了气的轮胎 36、a flat tyre 走了气的轮胎 37、a puncture 轮胎被扎破 38、to extend the flaps (to retract the flaps) 放下襟翼（收上襟翼） 39、gear extention (gear retraction) 起落架放下（起落架收上） 40、The gear is jammed. 起落架被卡死。 41、The flaps are jammed. 襟翼被卡死。 42、the emergency extention system 应急放下系统 43、to crank the gear down 摆动放下起落架 44、the brakes 刹车
焊接术语
1 alloy flux 合金焊剂 2 all-weld-meta l test specimen 全焊缝金属试样 3 arc gouging 电弧刨槽 4 as-welded 焊后状态 5 automatic welding 自动焊接 6 backgouging 清根 7 backing 衬垫 8 backing pass 背部焊道 9 backing ring 衬环环形衬垫 10 backing weld 打底焊缝 11 back weld 背部焊缝 12 base meta l 母材 13 bevel angle 坡口面角度 14 box tubing 箱形管 15 boxing 包角焊 16 butt joint 对接接头 17 butt weld 对接焊缝 18 cap pass 盖面焊道 19 caulking 捻缝 20 complete fusion 完全熔合 21 complete joint penetration 接头完全熔透 22 complete joint penetration groove weld 接头完全熔透坡口焊缝
23 complete penetration 完全熔透 24 continuous weld 连续焊缝 25 contractor 承包商 26 corner joint 角接接头 27 cover pass 盖面焊道 28 crater 弧坑 29 defect 缺陷 30 defective weld 缺陷焊缝 31 depth of fusion 熔深 32 discontinuity 不连续性 33 downhand 俯焊 34 drawings 图纸 35 edge angle 边缘角 35 effective length of weld 焊缝有效长度 36 electrogas welding（EGW) 气电焊 37 electroslag welding(ESW) 电渣焊 39 fatigue 疲劳 40 faying surface 贴合面 41 filler meta l 填充金属 42 fillet weld leg 角焊缝焊脚 43 flare-bevel-groove weld 喇叭形－斜边坡口焊缝 44 flash 飞边
房务部专业术语中英文对照
房务部：Rooms Division 前厅部：Front Office 客房部：Housekeeping 大堂副理：Assistant Manager 宾客关系主任：Guest Relation Officer 前台：Front Desk 接待处：Reception/Check-in 收银处：Cashier/Check-out 领班：Captain 主管：Supervisor 班次负责人：Shift Leader 商务中心：Business Center 客房服务代表：Guest service agent(接待和收银合并之后的前台人员的称呼)简称GSA 电话总机：Switch Board 接线员：Operator 预订处：Room Reservation 礼宾服务处：Concierge 大厅服务处：Bell Service 金钥匙：Golden Key 行政楼层：Executive Floor 行政酒廊：Executive Lounge 行李生：Bellman 迎宾员：Doorman 夜审：End of Day /Night auditor 2．前厅服务项目专业术语介绍 入住：Check-in 退房：Check-out 外币兑换：Foreign Currency Exchange 问询：Information 接送机服务：Pick up service 叫醒服务：Wake up call 请勿打扰服务：DND Do not disturbed 失物招领：Lost and Found 国内直拨和国际直拨电话：DDD and IDD Domestic Direct Dial and International Direct Dial对方付费电话：Collect Call 3．前厅常用物品术语介绍： 住宿登记单：Registration card 欢迎卡：Welcome card 订房凭证：Voucher 交接本：log book 信封：Envelope 房卡钥匙：Room key 安全保管箱：Safe Deposit Box 客房统计和出售率统计的术语 预离房：Expected Departure 预抵房：Expected Arrival
焊接专业英语词汇(通用部分)
焊接专业英语词汇（通用部分） acetylene 乙炔am pere 电流安培 angle welding 角焊arc 电弧 argon arc welding 氩弧焊接bare electrode 光熔接条 butt welding 对接焊接cam ber 电弧弯曲 cascade 阶叠熔接法clad weld 被覆熔接 crator 焊疤excess m etal 多余金属 filler rod 焊条fillet weld 填角焊接 gas shield 气体遮蔽groove welding 起槽熔接 hand face shield 手握面罩hard facing 硬表面堆焊 jig welding 工模焊接laser beam welding 雷射光焊接 metal electrode insert gas welding MIG熔接nugget 点焊熔核overlaying 堆焊peening of welding 珠击熔接法 plug welding 塞孔熔接positioned welding 正向熔接 pressure welding 压焊propane gas cutting 丙烷气切割 pure nickel electrode 纯镍熔接条reinforcem ent of weld 加强焊接resist 抗蚀护膜root running 背面熔接 seam焊缝seaming 接合 seam welding 流缝熔接series seam welding 串联缝熔接 skip welding process 跳焊法spark 火花 spot welding 点焊接stitch welding 针角焊接 stud arc welding 电弧焊接under laying 下部焊层 void 焊接空隙weld flow m ark 焊接流痕 weld flush 焊缝凸起weld line 焊接纹 weld m ark 焊接痕weld penetration 熔接透入 weld zone 焊接区welding 焊接 welding bead 焊接泡welding direction 焊接方向 welding distortion 焊接变形welding flux 焊剂 welding ground 电熔接地welding interval 焊接周期 welding stress 熔接应变welding torch 熔接气炬 welding electrode production line 电焊条生产线 welding electrode 焊条 welding fixture 焊接夹具 welding generator 电焊机 welding goggles 焊工护目镜 welding gun 焊枪 welding helmet 电焊帽 welding inspection ruler 焊接检验尺 welding machine 焊接机 welding mill 焊管机 welding motor generator 电动焊接发电机 welding nozzle 焊嘴 welding paste 焊接药膏
焊接术语
焊接术语 焊接术语 1 主题内容与适用范围 本标准规定了焊接（包括软、硬钎焊及热切割）专业的常用标准术语名称、定义及对应英文名称。 本标准适用于编写国家标准、行业标准、企业标准以及技术书籍、教材、论文报告。 2 一般术语 2.1 焊接 welding 通过加热或加压，或两者并用，并且用或不用填充材料，使工件达到结合的一种方法。2.2 焊接技能 welding technique 手焊工或焊接操作工执行焊接工艺细则的能力。 2.3 焊接方法 welding process 指特定的焊接方法，如埋弧焊、气保护焊等，其含义包括该方法涉及的冶金、电、 物理、化学及力学原则等内容。 2.4 焊接工艺 welding procedure 制造焊件所有关的加工方法和实施要求，包括焊接准备、材料选用、焊接方法选定、 焊接参数、操作要求等。 2.5 焊接工艺规范（程） welding procedure specification 制造焊件所有关的加工和实践要求的细则文件，可保证由熟练焊工或操作工操作时 质量的再现性。 2.6 焊接操作 welding operation 按照给定的焊接工艺完成焊接过程的各种动作的统称。 2.7 焊接顺序 welding sequence 工件上各焊接接头和焊缝的焊接次序。 2.8 焊接方向 progress of welding 焊接热源沿焊缝长度增长的移动方向。 2.9 焊接回路 welding circuit 焊接电源输出的焊接电流流经工件的导电回路。 2.10 坡口 groove 2.11 开坡口 beveling (of the edge ) 用机械、火焰或电弧等加工坡口的过程。 2.12 单面坡口 single groove 只构成单面焊缝（包括封底焊）的坡口。 2.13 双面坡口 double groove 形成双面焊缝的坡口。 2.14 坡口面 groove face 2.15 坡口角度 groove angle 两坡口面之间的夹角，见图3。 2.16 坡口面角度 bevel angle, angle of preparation 待加工坡口的端成现坡口面之间的夹角，见图3。
焊接专用英文词汇
焊接专用英文词汇 1.1 焊接方法 焊接方法与设备（Welding process& facility） 手工电弧焊(MAW:manual arc welding) 电弧焊（arc welding）埋弧电弧焊（SAW：submerged arc welding）气焊（gas welding）氩弧焊（argon arc welding） 气体保护电弧焊 CO2保护焊(CO2 shielded arc welding) 熔化焊（GMAW—gas metal arc welding） fusion welding 电渣焊(ESW—electroslag welding) 激光焊(LW—laster welding) 等离子焊(PAW—plasma arc welding) 摩擦焊（FRW—friction welding） 焊接压力焊超声波焊（UW—ultrasonic welding） welding pressure welding 冷压焊（CPW—cold pressure welding）锻焊（FW—forge-welding）对焊butt welding 电阻焊(RW—resistance welding) 缝焊seam welding 点焊spot welding 烙铁钎焊 iron soldering 火焰钎焊 torch brazing/ torch soldering 钎焊炉中钎焊 furnace brazing/ furnace soldering soldering/brazing 盐浴钎焊 saltbath dip brazing (soldering) 真空钎焊 vacuum brazing 堆焊 overlaying welding 平焊 downhand welding/flat welding 横焊 horizontal welding 立焊 vertical welding 仰焊 overhead welding 全位置焊 all position welding/positional welding 半自动电弧焊 Semi-automatic arc welding 钨极惰性气体保护电弧焊 (TIG) tungsten inert-gas arc welding 熔化极惰性气体保护电弧焊（MIG）metal inert-gas arc welding 1.2 焊接设备 电弧焊机 arc welding machine 直流弧焊机 DC arc welding machine 交流弧焊机 AC arc welding machine 交直流两用弧焊机 AC/DC arc welding machine 氩弧焊机 argon arc welding machine 二氧化碳弧焊机 CO2 arc welding machine 埋弧焊机 submerged arc welding machine 焊接机头 welding head 行走机构 traveller 送丝机构 wire feeder 焊丝盘 wire reel
电气专业术语中英文对照
一．电气名词 Electric items 二．线路（母线、回路）Lines (Bus , circuits) 三．设备 Equipments 四．保护、继电器 Protection , relays 五．电气仪表 Electric instruments 六．防雷 Lightning protection 七．接地 Grounding , earthing 八．室、所 Room , Substation 九．电修车间设备 Equipments of electric repair 十．材料 Material 十一．图名 Drawings , diagrams 十二．表头 Tables 十三．标准图词汇 Terms from standard DWG 一．电气名词 Electric items 交（直）流 Alternating (direct) current 短路电流 Short-circuit current 起始次暂态短路电流 Initial subtransient short-circuit current 冲击电流 Impulse current 稳态短路电流 Steady state short-circuit current 临界电流 Critical current 切断电流 Rupturing current 熔断电流 Blow-out current 故障电流 Fault current 计算电流 Calculating current 极限有限电流 Limit effective current 过电流 Over current 逆电流 Inverse current 整定电流 Setting current 额定电流 Rated current 电流密度 Current density 短路电流最大有效值 Maximum effective value of short-circuit current 高压 High-voltage , High-tension 低压 Low-voltage , Low-tension 计算电压 Calculating voltage 激磁电压 Exciting voltage 冲击电压 Impulse voltage 临界电压 Critical voltage 残留电压 Residual voltage 击穿电压 Puncture voltage 脉动电压 Pulsating voltage 供电电压 Supply voltage 电力电压 Power voltage
焊接术语翻译
焊接术语翻译 喇叭形坡口 flare groove 锁底坡口 single bevel groove with backing locked 坡形板边tapered edge 焊缝weld 接逢seam 焊缝符号 welding symbol 焊缝金属weld metal 填充金属filler metal 熔敷金属 deposited metal 焊缝表面 weld face/ face of weld 焊缝背面back of weld 焊缝轴线axis of weld 焊缝尺寸size of weld 焊缝宽度 weld width/ width of weld 焊缝长度 weld length/ length of weld 熔深 penetration/ depth of penetration 焊缝成形 appearanee of weld 焊缝成形系数 form factor of weld 余高 rein forceme nt/ excess weld metal 背面余高 root reinforcement 削平焊缝 flush weld/ weld machined flush 对接焊缝butt weld 角焊缝fillet 焊脚 leg/ fillet weld leg 角焊缝断面形状 profile of fillet weld 平形角焊缝flat fillet 凸形角焊缝 convex fillet weld 凹形角焊缝 con cave fillet weld 角焊缝凹度concavity 侧面角焊缝 side fillet weld/ fillet weld in paralle lshear 焊缝有效长度 effective len gth of weld 焊 缝厚度 throat depth/ throat thickness 焊缝 计算厚度 theoretical throat 立角焊缝 fillet weld in the vertical position 横角焊缝 fillet weld in the horizontal position 正面角焊缝 front fillet weld/ fillet weld in normal shear 焊缝实际厚度 actual throat
电影专业术语 中英对照
电影专业术语中英文对照 A Above-the-line 线上费用 A-B roll A-B卷 AC 交流电 Academy ratio 学院标准画框比 Adaptation 改编 ADR editor ADR 剪辑师 Aligator clamp=gaffer grip 固定灯具的弹簧夹，又称鳄鱼夹 Ambient Sounds 环境音 Amp 安培 Amplification 信号放大 Amplitude 振幅 Analog 模拟 Anamorphic lens 变形镜头 Aperture 光圈 Answer Print 校正拷贝 Arc 摄像机的弧度运动 Art director 艺术指导 Aspect ratio 画框比 Atmosphere sound 气氛音 Attack 起音 Audio board 调音台 Audio mixer 混音器，混音师 Automatic dialogue replacement 自动对白补录 Automatic focus 自动对焦 Automatic gain control 自动增益控制 Automatic iris 自动光圈(少用) Axis of action 表演轴线 B Back light 轮廓光 Background light=Scenery light 场景光 Balance 平衡 Balanced 平衡电缆 Barndoor 遮扉（灯具上的黑色金属活动板，遮光用的） Barney 隔音套 Base 片基（用来附着感光乳剂的胶片基底） Base plate 底座（固定灯的） Baselight level 基本亮度 Batch capturing 批次采集 Below-the-line 线下费用 Bidirectional 双向麦克风 Bit depth 位元深度（在数字声音中每次取样的数目，通常是8，12,16）
焊接术语
1、Apertures开口，钢版开口 指下游SMD焊垫印刷锡膏所用钢版之开口。通常此种不锈钢版之厚度多在8mil 左右，现行主机板某些多脚大型SMD，其I/O 达208 脚或256 脚之密距者，当密印锡膏须采厚度较薄之开口时，则须特别对局部区域先行蚀刻成为6 mil之薄材，再另行蚀透成为密集之开口。下图为实印时刮刀与钢版厚薄面各开口接触之端视示意图。 2、Assembly 装配、组装、构装 是将各种电子零件，组装焊接在电路板上，以发挥其整体功能的过程，称之为Assembly。不过近年来由于零件的封装(Packaging)工业也日益进步，不单是在板子上进行通孔插装及焊接，还有各种SMD 表面黏装零件分别在板子两面进行黏装，以及COB、TAB、MCM 等技术加入组装，使得Assembly 的范围不断往上下游延伸，故又被译为"构装"。大陆术语另称为"配套"。 3、Bellows Contact 弹片式接触 指板边金手指所插入的插座中，有一种扁平的弹簧片可与镀金的手指面接触，以保持均匀压力，使电子讯号容易流通。 4、Bi-Level Stencil双阶式钢版 指印刷锡膏所用的不锈钢版，其本身具有两种厚度( 8mil 与6mil )，该较薄区域可刮印脚距更密的焊垫。本词又称为Multi-level Stencil。 5、Clinched Lead Terminal 紧箝式引脚 重量较大的零件，为使在板子上有更牢固的附着起见，常将穿过通孔的接脚打弯而不剪掉，使作较大面积的焊接。 6、Clinched-wire Through Connection 通孔弯线连接法 当发现通孔导通不良而有问题或断孔时，可用金属线穿过通孔在两外侧打弯， 7、Component Orientation 零件方向 板子零件的插装或黏装的方向，常需考虑到电性的干扰，及波焊的影响等，在先期设计布局时，即应注意其安装的方向。 8、Condensation Soldering凝热焊接，气体液化放热焊接 又称为Vapor Phase Soldering，是一种利用高沸点有机液体之蒸气，于特定环境中回凝成液态所放出的热量，在全面迅速吸热情形下对锡膏进行的熔焊，谓之"凝焊"。早期曾有少部份业者将此法用在熔锡板的"重熔"方面。先决条件是该溶剂蒸气的温度须高于焊锡熔点30℃以上才会有良好的效果。 9、Contact Resistance 接触电阻 在电路板上是专指金手指与连接器之接触点，当电流通过时所呈现的电阻之谓。为了减少金属表面氧化物的生成，通常阳性的金手指部份，及连接器的阴性卡夹子皆需镀以金属，以抑抵其"接载电阻"的发生。其它电器品的插头挤入插座中，或导针与其接座间也都有接触电阻存在。
焊接专业术语中英对照.
焊接专业术语中英对照焊接欠缺与检验 焊接欠缺welding imperfection 焊接缺陷weld defect 气孔blowhole/ gas pore 针尖状气孔pinhole 密集气孔porosity 条虫状气孔wormhole 裂纹crack 表面裂纹surface crack 咬边undercut 焊瘤overlap 凹坑pit 烧穿burn through 塌陷excessive penetration 未焊透incomplete penetration/ lack of penetration 未熔合lack of fusion/ incomplete fusion 未焊满incompletely filled weld 根部凹陷root concavity 电弧擦伤arc scratch 夹渣slag inclusion 夹杂物inclusion 夹钨tungsten inclusion 白点fish eye/ flake 错边misalignment/ dislocation 焊接检验 试件test piece 试样test specimen 无损检验nondestructive test 破坏检验destructive test 外观检查visual examination 超声波探伤ultrasonic inspection 直射法超声波探伤straight beam method 斜射法超声波探伤angle beam method 液浸法超声波探伤immersion method 射线探伤radiographic inspection/ radiography X射线探伤X-ray radiographic inspection γ射线探伤gamma-ray inspection X射线工业电视探伤X-ray industrial television inspection 磁粉探伤magnetic particle inspection 电磁探伤electromagnetic inspection/ eddy current test 探伤灵敏度flaw detection sensitivity 渗透探伤penetration inspection 荧光探伤flurescent penetrant inspection 着色探伤dye penetrant inspection 密封性检验leak test 气密性检验air tight test 枕形气密检验pillow test 耐压检验pressure test 水压检验hydraulic test 气压检验pneumatic test 液晶检验liquid crystal test 声发射检测acoustic emission testing 面弯试验face bend testing 背弯试验root bend test 侧弯试验side bend test 横弯试验horizontal bend test 纵弯试验axial bend test 压扁试验squeezing test actual weld-throat thick-ness焊缝厚度 all-around weld整周焊缝 all-around weld (整周焊缝)环焊缝 angle butt weld斜对接焊 angle weld角焊 appearance of weld焊缝成形 arc-seam weld电弧缝焊 arc-spot weld电弧点焊 arc-weld电弧焊 aspect ratio of weld焊缝成形系数 at weld edge在焊缝边上 attachment weld连接焊缝 automatic spot weld自动点焊法 automatic weld自动焊接 axis of a weld焊缝行南? 焊接轴线 axis of weld焊缝轴线; 焊接轴线 back of weld焊缝背面 backing groove of weld焊缝反面坡口backing weld底焊; 底焊焊缝 bare metal arc weld裸焊条电弧焊 bead weld珠焊; 堆焊 bead-on-plate weld堆焊焊缝 beading weld凸焊 beam-to-beam weld梁间焊接; 梁式引线焊接block sequence weld分段多层焊 bond weld钢轨接头焊接 bridge seam weld桥缝焊接; 桥线焊 brize weld硬焊 butt weld对接焊缝 butt weld ends对头焊接端 butt-weld碰焊; 平式焊接; 对头焊接 butt-weld in the downhand position对接平焊