变压器专业中英文词汇
45ºmitred joint 45º斜接缝
a complete 成套设备
a lamination stack 一叠铁心
A-A enlarged A-A放大
A-A section A-A剖面
abbreviation 缩写
abscissa X-axis 横坐标
absorbent 吸附剂
absorption ratio of insulation resistance 绝缘电阻吸收比acceleration 加速度
acceptance inspection 验收检验
accessories 附件
accuracy 准确度
accuracy class 准确级次
accuracy limit factor 准确限值因数
acetic acid ethylic 醋酸
acetone 丙酮
acetone extraction of insulating material 绝缘材料丙酮抽出物acetylene 乙炔
acid value 酸值
acryl 丙烯
active aluminium oxide (activated alumine) 活性氧化铝
active part assembly 器身装配
additional insulation of lead 引线附加绝缘
additional loss 附加损耗
admittance 导电率
air (water) cooler 风(水)冷却品
air core reactor 空心电抗器
air exhausting pipe 导气管
air gap 空气隙
alignment对中心(不对中心)
alkyd base lacquer 酚醛漆
aluminium-alloy conductor 铝合金导线
ambient temperature 环境温度
angle 角钢(槽钢)
angular contact ball bearing 向心止推滚珠轴承
annealed conductor 退火导线
annex (appendix) to the contract合同附件
annular gear 内齿轮
anticoagulent 抗凝剂
anti-corna coating 防叠层
anti-dust washer 防尘垫圈
anti-magnetic steel (low-temperature steel) 抗磁钢(低温钢)antioxidant 抗氧化剂
antirust primer 防锈底漆
apparent charge 视在电荷
approximate 近似于
arc-suppression reactor 消弧电抗器
argon protected welding 氩弧焊
ascending flanged base 升高座
assignment for technical design 技术任务书
atmospheric over voltage 大气过电压
autographic recording instrument 自动记录仪表
automatic assembly scaffold 自动升降装配架
automatic lathe 自动车床
automatic submerged-arc wilding 埋弧自动焊
autotransformer 自耦变压器
autotransformer regulator 自耦调压器
auxiliary winding 辅助线圈
availability 可用性
axial (radial) leakage flux 轴向(径向)漏磁通
axial strip 轴向撑条
aximum (minimum) tapping最大最小分接m
backing off lathe 铲背车床
bakelite coated insulating paper 上胶绝缘纸
bakelized paper board(cpoxy resin glass-fibre) 胶纸板(环氧玻璃布板)balance reactor 平衡电抗器
ballast 镇流器
band saw 带锯床
band spring 板弹簧
banding wire (rope) 绑线(绳)
barrel (petroleum) 桶(石油)
base plate of rating plate 铭牌底板
basic parts 基础件
B-B tuned by B-B转
beaker烧杯
beaker flask 坩埚
beaker flask 锥形瓶
bearing 轴承
bell type tank 钟罩式油箱
bench drill 台钻
bending die for steel tube 钢管压弯模
bending press 折板机
bending press (brake) 折板机(液压)
bevel gear 伞齿轮
block diagram 方框图
blue print 蓝图
booster (pump) 增压泵
booster tran- 增压变压器
boring machine 镗床
bracket (tensile rod) for cooler 冷却品托架
braided wire 辫子线
brake包闸
brazing pliers 铜焊钳夹
brazing tran- 钎焊变压器
brazing transformer 铜焊机
breather 呼吸品
breboard (fibretube) 碳化纤维纸板(管)fi bridge for testing of voltage transformation ratio 变比电桥bright bolt 光螺杆(螺母)
bright washer 光垫圈
British thermal unit 英制热量单位
broaching machine 拉床
bulging lathe 旋压车床
burden of an instrument transformer 互感器的负荷bushing current tran- 套管用电流互感器
bus-type current tran- 母线式电流互感器
butt joint core 对接铁心
button head cap screw 无头螺杆
cable clip 电缆夹
cable paper 电缆纸
cable through type HV bushing 穿缆式高压套管calendered insulating paper 压延绝缘纸
calibration 校准
calvanized bolt 镀锌螺栓
capacitor compensation device 电容补偿装置capacitor shield winding 插入电容式线圈
capacitor type current tran- 电容式电流互感器capacitor type current tran- 电容式电压互感器capstan and pulley block 绞盘与滑轮组
carbon monoxide 一氧化碳
Cartesian coordinate 笛卡儿坐标
cartridge of oil-filer 油过滤芯子
cascade testing transformer 串级式试验变压器
case No. 箱号
cast resin (resin moulded) transformer 塑料浇注变压器cast resin current tran- 塑料浇注式互感器
caterpillar crane 履带吊
Celsius(centigrade) , Kelvin 摄氏度, 开尔文
center of gravity 重心
CGS unit 厘米-克-秒单位制
chain block 手拉葫芦
check on connection group (polarity) 联结组(极性)校验
chevron gear 人字齿轮
chopped wave lighting impulse 截波雷电冲击
chopping device 截断装置
chromatography 气相色谱分析
circular (internal)grinder 外圆(内圆)磨床
circularity (ellipticity) 圆度(椭圆度)
circumscribed circle of core leg 芯柱外接圆
clamping ring for porcelain casing 瓷箱压圈
clear away burrs 去毛刺
clear away welding flux 消除焊药皮
clear away welding splashes 消除焊渣飞溅
co2 protected welding CO2保护焊
coach bolt 方头螺拴
coated with two layers of primer 涂两遍底漆
coiled spring盘簧
cold bending machine for profiles 形材冷弯机
cold pressing pliers 冷压焊钳
cold rolled grain oriented silicon sheet steel 冷轧晶粒取向硅钢片colloidal contamination of oil 油的胶体污染
colorimeter 比色计
coloured kerosene leakage test 火油着色试漏
combined instrument tran- 组合式互感器
combined voltage variation 混合调压
commissioning test 投运试验
complement angle 余角
complete self-protected single-phase tran- 全自动保护单相变压器complete substation 成套变电站
complex number 复数
component (assembly) parts 部件
composite conductor 复合导线
composite error 复合误差
compressing bolt with spring (hydraulic damper) 弹簧压钉(油缸压钉)computer aided design and manufacturing 计算机辅助设计computer aided test 计算机辅助实验
concrete (cement) reactor 水泥电抗器
condenser paper 电容器纸
conductance , conductivity 电导
conformity 合格
connecting box for fan-motors 风扇接线盒
connecting flange for evacuation (for oil filter) 真空接头(滤油接头)conservator with rubber diaphrage(bladder) 带隔膜储油柜
consignee收货人
consignor 发货人
constant flux voltage variation(C.F.V.V.) 恒磁通调压
container transport 集装箱运输
contents of drawing (documents) 图样目录
continuous winding 连续式线圈
control box (panel) 控制箱(盘)
control point 控制点
conventer transformer 变流变压器
copper (aluminium) foil 铜(铝)箔
copper (brass , bronze , phosphor bronze) 紫铜(黄铜,青铜,磷铜)copper height of winding 铜线高度
copper tape 铜带
copper wire screen 铜网
core earthing strip 铁芯接地片
core lamination 铁心片
core limb 铁心柱
core surface perpendicular to lamination 铁芯端面
core type 芯式
cork rubber 软木
corona discharge 电晕放电
Coulomb 库仑
coupling 联轴器
cover plate (temporary) 盖板(临时)
creepage distance 爬电距离
creeping discharge 沿面放电(爬电)
critical process 关键工序
cross-linked polymer cable 胶联聚合物电缆
crown nut 槽顶螺母
crucible 蒸发器皿
cup head bolt 半圆头螺栓
current density 电流密度
current tran- 电流互感器
current voltage error 电流电压误差
cycloidal gear 摆线齿轮
cylindarical gear 圆柱齿轮
cylindrical insulating barrier of HV bushing 高压套管绝缘护筒decimal 小数
deep-throat punching machine 深颈冲床
delivery date 发货日期
deoxygenized copper conductor 无氧铜导线
department 部门
design code 标准号
design review 设计评审
designating plate , illustration plate 标志牌,指示牌
designed , checked , approved 设计,校核,审定
destination 到站
detail list of drawing 零件明细表
detail list of purchased parts 外购件明细表
dew point measurement 露点测量
dielectric constant 介电常数
dielectric loss 介质损耗
dielectric strength insulation strength 绝缘强度
differential , differentiation 微分
differential gear 差动齿轮
digital display voltmeter 数字电压表
directed forced oil circulation cooling 油导向冷却
directed forced oil circulation forced air cooling 油导向吹风冷却disk saw 圆锯床
disk winding 饼式线圈(双饼线圈)
dismantle of upper yoke 拆除上轭
dismantled accessories 拆卸附件
dismountable parts可拆卸件
dispatch list 发货单
disruptive discharge 破坏性放电
distribution transformer 配电变压器
diverter switch 切换开关
dler gear空转齿轮i
don’t turn over 不准倒置
don’tstack up 不准叠放
double column punching machine 龙门冲床
double cotton covered enamel cable 双丝包线
double housing planer 双柱龙门刨
double-action punching machine 双动冲床
double-row bearing 双列滚珠轴承
draining valve 放油活门
drawing No. 图号
drill 钻床
drilled together with mating parts 与配合件同时钻孔
driving mechanism of OLTC 有载开关操作系统
dry type transformer 干式变压器
drying and compressing of winding 线圈的干燥与压缩drying with hot-air circulation 循环热风干燥
duplicates 复制图
eads clamping (supporting frame) 引线夹(支架)
earthed voltage tran- 接地电压互感器
earthing mark 接地标志
earthing screen of core (side yuoke) 铁芯地屏(旁轭地屏)earthquake , seism 地震
eccentricity (concentricity) 偏心度(同心度)
eddy current loss 涡流损耗
edge shaping 刨边
elastic washer 碟形弹簧
electrostatic plate (ring) 静电板(环)
electrostatic shielding 静电屏蔽
enameled wrapped conductor 漆包线
end insulation 端绝缘
engaging angle 压力角
engaging tooth 啮合齿
epoxy-bound bandage 环氧绑扎带
error 误差
error compensation 误差补偿
esiccator干燥管 d
ethylene 乙烯
evenness 整齐度
evolute core 渐开线铁心
evolution extraction of root 开方
examination and appraisal program 检验鉴定大纲expander 膨胀器
explosion-proof pipe 安全气道(防爆筒)exponent , exponential 幂
extrapolation method 外推
eyebolt 吊环螺丝
facing boring lathe 落地镗床
Farad , pico-farad 法拉, 皮克法拉
faraday cage 法拉第笼
farthing bushing (terminal) 接地套管(端子)feasibitilystudy 可行性分析
ferrous metal (non-ferrous metal) 黑色金属(有色金属)filament tran- 灯丝变压器
final assembly 总装配
final inspection 最总检验
finalization of design 设计定型
finalized revision 定形改版
finish(roughness)表面光洁度(粗糙度)
finite element method 有限元法
first item inspection首件试验
flame-proof tran- 防爆变压器
flash point (congealing point )of oil 油闪点(凝固点)flashover 闪络
flask 长颈瓶
flat washer 平垫圈
flatness 平(不平)度
flexible cable 软电缆
flexible connecting strip 软接线片
floating crane 浮吊
flow quantity (m³/min) 流量
flow relay 流动继电器
fluorescent leakage test 荧光试漏
flux density 磁通密度
foil winding 箔式线圈
foot 呎
foot pad 垫脚
for unmarked 其余
for unmarked edges 其余倒角
forced oil air cooling (water cooling) 强油风冷(水冷)forging (die casting) 煅件(压铸件)
fork lift 叉车
form-fit tank 适形油箱
foundation drawing 地基图
fraction, numerator, denominator 分数,分子,分母fractional turn (integer turn) 分数匝(整数匝)frequency meter 频率表
frequency response 频率响应
full thread bolt 全螺纹螺拴
full wave lighting impulse 全波雷电冲击
furnace transformer 电炉变压器
gallon 加仑
galvanized 镀锌
gas (moisture) content of oil 油中含水量(含气量)
gas cutting (automatic gas cutting) 气割
gas insulated transformer 气体绝缘变压器
gas relay 气体继电器
gas separating property of oil 油的吸气性
gate (butterfly,ball) valve 闸阀(蝶阀,球阀)
gauss 高斯
gear 齿轮
gear slotting 插齿机
general layout 总图
general parts 外购件
generator transformer 发电机变压器
Geneva (spider , universal joint cross) 方向联(十字接头)gentian violet 龙胆紫
glass fibre woven tape 玻璃丝带
glass-fibre covered conductor 玻璃丝包线
gorse power 马力
graphic method 图解法
gravitational acceleration 重力加速度
grinder 磨床
grinding to flat after welding 焊后磨平
grip nut 夹紧螺母
gross weight 毛重
hack saw 弓锯床
hand hole (manhole) 手孔(人孔)
handled with care 小心轻放
hard drawn copper conductor 硬拉铜导线
hardening 淬火
heavy current bushing 大电流套管
helical gear , screw gear 斜齿轮
helical winding 螺旋式线圈
here in after referred as XX 以下简称为XX
hexagonal head bolt 六角头螺栓
hexagonal socket head bolt 内六角头螺栓
high frequency 高频
high vacuum period高真空阶段
high voltage 高压示波器
high voltage (low, mid-) winding 高压线圈(中压,低压)high-density pressboard 高密度纸板
hinge pin 胶联销
hoisting crane 起重机
horizontal oil-duct 横向油道
hot (hottest) spot 热点(最热点)
hot dipping 热浸
hot-oil circulation 热油循环
hot-rolled (cold-rolled) silicon sheet steel 热轧(冷轧)硅钢片hydraulic jacks for winding compression 线圈油压千斤顶hydraulic planer 液压刨床
hydraulic pump station 油压泵站
Hysteresis loss 磁滞损耗
iacquer showering 淋漆(喷漆)
ickling酸洗
illustrative drawing 示意图
illustrative drawing for winding connection 线圈连接组图illustrative drawing for winding terminals 线圈端子位置示意图imaginary number component 虚数部分
impedance voltage 阻抗电压
improper fraction 假分数
impulse voltage generator 冲击电压发生器
inclination 倾斜度
inconcentricity不同心度
indication mark 指示标记
induced over voltage withstand test 感应耐压试验
inductivemethod 归纳法
infrared scanner 红外线扫描仪
infrared scanning 红外线扫描
inhibited (un-) oil 阻化油(非阻化油)
initial terminal (final terminal ) of winding 线圈起始端(终)inner connecting stud of HV bushing 高压套管导杆头
in-process inspection 工序间试验
installation drawing 安装图
instruction for technical design 技术设计说明书
insulating cylinder 绝缘纸筒
insulating filling strips between turns 线匝间垫条
insulating level 绝缘水平
insulating material (heat-resistant material) 绝缘材料(保温材料)insulating paper (press board) 绝缘纸(纸板)
insulation angled ring (collar ring) 绝缘角环
insulation assembly 绝缘装配
insulation between turns 匝间绝缘
insulation breakdown 绝缘击穿
insulation diaphragm on the tank wall 箱壁绝缘隔板
insulation resistance 绝缘电阻
insulation wrapping 绝缘包扎
integrate , integration 积分
intensity of pressure 压强
interconnecting transformer 联络变压器
interleaved winding 纠结式线圈
interleaved-continuous winding 纠结-连续式线圈
internal external insulation 内外绝缘
interpolation method 插入法
introduction voltage regulator 感应调压器
involute gear 渐开线齿轮
involution 乘方
involve to the fifth power , 5th power of n n的五次方
iron core reactor 铁心电抗器
iron red epoxy primer 环氧铁红底漆
isolation tran- 隔离变压器
jig boring machine 坐标镗床
joint flange for enclosed bus-bar 封闭母线联接法兰
Joule 焦耳
kerosene evaporator 煤油蒸发器
kerosene recycling pump 煤油回收泵
kilometer 公里
kilowatt-hour 千瓦时
kraft paper 牛皮纸(青壳纸)
lacquer of amidoalkyd base 胺基醇酸漆
lacquer of nitrocellulose 硝基漆(硝基清漆)
lacquer thinner 稀释剂
ladder with balustrade 有围栏的梯子
lag bolt 水螺丝
laminated pressboard 层压纸板
lamination drawing diagram 铁心叠积图
lamination factor 叠片系数
lamination inserting knife 插板刀
large size long layer winding 大型层式线圈
lathe 车床
layer insulation (insulation between disk) 层绝缘(段)layout 刻线
lead (tin, silver, zinc) 铅(锡,银,锌)
lead insulation wrapping machine 引线绝缘包扎机leakage lest on sealed parts 密封式滤
lift 扬程
lifting lug (lifting eyebolt) 吊拌(吊环)
lifting lug with bearing plate for jacks 吊板与千斤顶支座Liter , cubic decimeter 升, 立方分米
load loss 负载损耗
loading capacity 装载量
local over hot 局部过热
locating pin 定位销
locking nut 梭螺母
locking washer 止退垫圈
long-creepage bushing 加强式套管
longitudinal insulation 纵绝缘
loss tangent 介损角的正切值
low carbon steel (alloy steel) 低碳钢(合金钢)
low power factor wattmeter 低功率因数瓦特表
lug washer 止退线圈
machine direction 抄纸方向
magnetic flaw detection 磁力探伤
magnetic saturation voltage regulator 磁饱和调压器magnetic shielding 磁屏蔽
magnetic type oil-level indicator 磁铁式油位指示器main insulation 主绝缘
major (minor) diameter of gear 齿轮外(齿底)直径marine tran- 船用变压器
market survey 市场调查
marshalling yard 铁路编组站
mating parts 配合件
maximum likelihood method 最大似然法
maximum minimum 最大,小
measuring flask 量瓶
medium frequency 中频
memory scope 记忆示波器
metallic hose 金属软管
metallized paper (crepe paper) 金属化纸(金属化皱纹纸)meter , decimeter , centimeter millimeter 米, 分米, 厘米, 毫米methane, ethane 甲烷(乙烷)
mile , knot 英里, 海里
miller 铣床
mining tran- 矿用变压器
modulus 模数
moulded insulatingparts 成型绝缘件
movable (trailer mounted) type 移动式(列车式)
movable oil purificator 移动式净油站
movable radial drilling machine 移动式摇臂转床
movable substation 移动式变压器
moving-coil voltage tran- 移圈调压器
multi-point spot welder 多点焊机
name 名称
natural cooling (air blast cooling) 自然冷却(吹风冷却)natural frequency of vibration 自振频率
neutral bushing 中点套管
Newton , dyne 牛顿, 达因
nikel镀镍
nitrocellulose lacquer 硝基漆
niversal miller万能铣床u
no-load current 空载电流
no-load loss 空载损耗
nominal value 标称值
nonconformity 缺陷
non-distructive flaw detection无损探伤
noninflammable medium impregnated trans- 浸难燃油变压器normal distribution 正态分布
northeast china ash tree 水曲柳
n-shaped clips for upper yoke 轭片N型夹
number item 项号
number of ampere-turns 安匝数
numerical control lathe 数控车床
nut locked by punching three points 冲铆三点锁紧螺母
nut of compressing bolt 压钉螺母
obtuse (acute) number 钝锐角
Oersted 奥斯特
ogee washer 曲面垫圈
oil base (paraffin base ,naphthene base) 油基(石蜡基,环烷基)
oil conduit 导油管
oil impregnation under vacuum 真空浸油
oil sampling valve (plug) 油样活门
oil tester 油试验器
oil-dehydrating device 油脱水装置
oil-duct air ventilating duct of core 铁心油道(气道)
oil-immersed air cooling 油浸风冷
oil-immersed forced directed oil circulation air cooling油浸强迫导向风oil-immersed forced oil circulation air cooling 油浸强迫油循环风冷oil-immersed natural cooling 油浸自冷
oil-immersed transformer 油浸式变压器
oil-proof rubber 抗油橡胶
oil-submerged pump 潜油泵
on’t uncouple with slipping 不准流放d
on-load tap-changer (OLTC) 有载开关
open side planer 单臂刨床
open web girder wagon 落孔车
open-delta connection 开口三角连接
opening mechanism of autoclave cover 缸开启开油缸
operating handle of driving mechanism 操作机构手柄
operation instruction of transformer 变压器使用说明书
ordinate Y-axis 纵坐标
originals (transparent print) 底图
oscillating frequency 振荡频率
outdoor (indoor, pole mounting)type 户外(户内)式,柱上式over voltage 过电压
overall dimension 外形尺寸图
overall height of winding 线圈总高度
overall hydrocarbon content 总烃含量
oversize transport 限速运输
oxygen, nitrogen, hydrogen 氧(氮,氢)
oymide 聚酰胺pl
packaged in crate 花板包装
packing list 装箱单
pad frame for tank rim gasket 箱沿护框
pallet 底拖
paper channel 纸槽
paper moulded insulating part 绝缘成型件
paper size 纸型
paper wrapped conductor 纸包线
parallel 平行
parallel wound conductors 并绕导线
parallelism 平行度
partial discharge 局部放电
partial discharge extinction voltage 局部放电终止电压partial discharge inception voltage 局部放电起始电压partial discharge tester 局放测试仪
partial-interleaved winding 部分纠结式线圈
particle content of oil 油中颗粒数
partition 隔板
parts 零件
parts per million 百万分之一
parts subjected to wear 易损件
Pascal 帕斯卡, 千帕
peak value 峰值
peak value voltmeter 峰值电压表
per unit value 标值
perpendicular 垂直
perpendicularity 垂直度
pertaining to assembly drawing No. 隶属装配图号
phase displacement 相位差
phase displacement (instrument transformer) 相角差(互感器)phosphorated 磷化
phosphor-copper brazing metal 磷铜焊料
pieced together 铆接
pilot pin 导销
pin 销钉
pipe bending machine 弯管机
pitch diameter of gear 齿轮节距
pitot relay 皮托继电器
plain cotton tape 白布带
planer type miller 龙门铣床
planiform drawing of winding 线圈展开图
plasma cutting 等离子切割
platinum (g old, antimony, mercury) 铂(金,锑,汞)plywood 层压木板
pocket for mercury thermometer 水银温度计座
poise , Centpoise 泊, 厘泊
polar coordinate 极坐标
polyacetal (polyester)resin 聚缩醛(聚脂)树脂polyacrylic resin 聚丙烯酸树脂
polyacrylonitrile 聚丙稀酯
polycarbonate 聚碳酸酯
polychloroprene rubber 氯丁橡胶
polymide 聚酰亚胺
polyurethane 聚胺酯
polyvinyl acelated 聚醋酸乙烯酯
polyvinyl acetal 聚乙烯缩醛
polyvinyl alcohol 聚乙烯醇
polyvinyl chloride 聚氯乙烯
polyvinyl resin 聚乙烯树脂
porcelain casing (instrument transformer) 瓷箱(互感器)
porcelain type current tran- 瓷箱式电流互感器
port of loading 装货港口
positioning pin 定位钉
positioning plate 定位板
positioning stud 带螺母的定位柱
positive negative number 正负数
potential gradient 电位梯度
pound , pound per square inch 磅, 磅/平方寸
power frequency 工频
power plant transformer 厂用变压器
power transformer 电力变压器
power transformer with OLTC (off-circuit tap-changer) 有(无)载调压电力变压器precipitation well 沉淀盒(集污盒)
preliminary 初步设计
press 压力机
pressure relief valve 压力释放阀
principle circuit diagram 线路原理图
probability 概率
product appraisal 产品鉴定
proportional (inversely proportional) to 成正比
pulp 纸浆
punch press 冲压机
punch shear 剪断机
quality certificate 产品合格证
quality control 质量(质量控制)
quality guarantee 质量保证体系
quality management 质量管理
quality policy 质量方针
quality rated cost 质量成本
quality supervisor 质量监督
quantity 数量
radial drill 摇臂钻
radial spacer between disk 段间横垫块
radial strip 径向撑条
railway crane 铁路轨道吊
railway highway transportation 铁路(公路)运输
rated accuracy limit primary current 额定准确极限值的一次电流
rated burden of an instrument transformer 额定负荷
rated continuous thermal current 额定连续热电流
rated current 额定电流
rated dynamic current 额定动稳定电流
rated instrument security current 额定仪表保安电流
rated lighting impulse withstand voltage 额定雷电冲击耐受电压rated power 额定容量
rated short thermal current 额定短时热电流
rated tapping 额定分接
rated voltage 额定电压
rated voltage factor 额定电压因数
rated voltage ratio 额定电压比
rated withstand voltage 额定耐受电压
rating plate data 铭牌数据
reactance voltage 电抗电压
reactor 电抗器
real number component 实数部分
ream after drilling 钻后绞孔
rectifier tran- 整流变压器
reduced weft cotton tape 稀纬布带
reductor 减速器
reference list of customers 产品用户一览表
regulating winding 调压线圈
reinsertion of upper yoke 插板
reliability 可靠性
repe paper皱纹纸(压光皱纹纸)c
residual voltage of an arrestor 避雷器的残压
resistance thermometer 电阻温度计
resistance voltage 电阻电压
resonance frequency 谐振频率
reverse 改版
reverse type current tran- 倒立式电流互感器
revolution per minute 每分钟转数
revolving fixture for core clamping fabrication 夹件焊装翻转架
ring nut 圆螺母(滚花螺母)
rivet 铆钉
roller (tapered roller) bearing 滚柱(锥形)轴承
rolling direction 轧制方向
root-mean-square value 有效值
round off 四舍五入
routine test 出厂检验
routine test report 出厂试验报告
rspex (polymethylmethacrylate) 有机玻璃(聚甲醛丙烯酸甲酯)Pe rubber bladder 胶囊
rubber cable 橡胶电缆
saddle bed lathe 马鞍车床
saddle bottomed wagon 凹形车
sandwich winding 交错式线圈
sandwich-interleaved winding 插花纠结式线圈
saturable reactor 饱和电抗器
scale比例
schering bridge 西林电桥
schnabel wagon 钳夹式车
screw 螺旋铣床
sealedenclosed type 密闭式,包封式
seam welder 缝焊机
secondary limiting e.m.f(security factor) 二次极限感应电流(保安因数)secondary terminal box 二次端子箱
sectional winding 分段式线圈
see XX , vide XX 参见XX
selector switch 选择开关
semi-conducting coating 半导体涂层
semi-conducting paper 半导体纸
semi-continuous winding 半连续式线圈
serial No. 产品序号
series reactor 串联电抗器
service condition 使用条件
shaper 刨边机
shaper 牛头刨床
shared parts 借用件
shearing 剪切
shearing machine 剪板机
sheathed cable 铠装电缆
shell type 壳式
shielded cable 屏蔽电缆
shielding 屏蔽
shipping dimension drawing 运输图
shipping mark 唛头
short time over voltage 短时过电压
short-circuit test 突发短路试验
short-duration power frequency withstand voltage短时工频耐受电压
shot-blast 吹砂(抛丸)
shrinkable tape 紧缩带
shrinkage of insulation under compression 绝缘的压缩收缩率
shunt reactor 并联电抗器
side yoke 旁轭
signaling thermometer 信号温度计
silica gel 硅胶
simulation method 模拟法
single layer (double, multi-) cylindrical winding 单层(双层,多层)圆筒式线圈single pole correction press 单点液压矫正机
single silk cover 单丝漆包线
single-lead (multi-lead) cable 单芯(多芯)电缆
single-phase transformer 单相变压器
single-row 单列螺旋
sitioning hole 定位孔po
slit nut 开口螺母
slotting machine 插床
smoothing reactor 平波电抗器
soldering 锡焊
spare parts 备件
special test 特殊试验
speed , velocity 速度
sphere-gap 球极
spiral bevel gear 斜齿伞齿轮
spline miller 花键铣床
split pin 开口销
split winding 分列线圈
spot weld 点焊
spot welder 点焊机
spring 弹簧
spur gear 正齿轮
square nut 方螺母
stage of lamination stacks 铁芯的级
stainless steel 不锈钢
standard atmosphere condition 标准大气条件
standard capacitor 标准电容器
standard deviation 标准偏差
standard international unit 标准国际单位制
standard parts 标准件
standard transposition 标准换位
standstill after oil-filling 注油后静放
star (delta, zigzag) connection 星形连接(三角形,曲折形,T形)starting autotransformer 启动自耦变压器
starting reactor 启动电抗器
steam heating radiators 蒸汽加热排管
steel cable 钢丝绳
steel plate surface pre-processing 钢板表面预处理
step response 方波响应
stepped lap core 阶梯接缝
step-up (step-down) transformer 升(降)压变压器
stiffening plate of yoke clamping 夹件加强铁
straightening 校直
straightness 直度
stray capacitance 杂散电容
stray loss 杂散损耗
stud pin 柱螺旋销
stud weld 标杆焊
stud welder 螺杆焊机
substation transformer 电站用变压器
summary of trial production 试制总结
superimposed charge 叠加电荷
supplementary angle 补角
surface coating 表漆
surface hardening 表面淬火
surface lathe 端面车床
surface thermometer表面温度计
surfacing lathe 断面车床
surge arrestor 避雷器
switching over voltage 操作过电压
symbol of product 产品代号
symmetrical parts 对称件
synthetic rubber 合成橡胶
table (graph) 图表
tack weld 点固焊
tank bottom 箱底
tank rim 箱沿
tank wall (with magnectic shield) 箱壁(带磁屏蔽)tanker 油罐车
tapered hole 锥度孔
tapered pin 锥销
tapping terminal 分接头
technical agreement 技术协议
technical and economical analysis 技术经济分析technical condition 技术条件
technical design 技术设计
technical document for product delivery 出厂技术文件temperature class of insulation 绝缘材料的耐温等级tempering 回火
tensile plate of core limb 铁心拉板
tensile rod 拉螺杆
terminal box (block) 端子箱
terminus determination of drying process 干燥的终点判断tertiary winding 第三线圈
Tesla 特斯拉
test tube 试管
testing generator set 试验发电机组
testing instrument 试验用仪器仪表
testing tran- 试验变压器
thermoelectric couple 热电偶
thermometer with remote indication 远距离温度计
thinner 溶剂(稀释剂)
thread hobbing machine 滚丝机
three-phase banks with separate single-phase tran- 单相变压器组成的三相组合three-phase neutral reactor 三相接地电抗器
three-phase tran- 三线圈变压器
three-phase transformer 三相变压器
through hole 透孔
thrust bearing 止推轴承
tightening device for winding cylinder 线圈纸筒较紧器
time to chopping 截断时间
time to crest ,virtual front time 波前时间视在波前时间
time to half value of crest 半峰值时间
title block of drawing 图纸标题栏
tong-type ammeter 钳形电流器
top jointing beam of upper yoke (side yoke) 上轭顶梁(侧梁)
top loading vacuum drying autoclave 立式真空缸
Torr 托
total weight of product 产品总重
traction (locomotive) tran- 列车牵引变压器
trailer 拖车
transformer connection between disks 段间过渡联线
transformer with H class insulation H级绝缘变压器
transformer with split windings 分裂变压器
transient characteristics error 暂态特性(误差)
transient over voltage 暂态过电压
transparent adhesive tape 透明粘带
transport weight 运输重
transportation dimension size 运输尺寸图
transported with nitrogen filling 充氮运输
transported with oil filling 充油运输
transposed conductor 换位导线
transposed connection between disks 段间换位联线
transposition by groups 分组换位
transposition of windings 线圈的换位
trimming of winding 线圈修整
truck 卡车
tube connecting flange 联管夹
tubular oil-level indicator 管式油位指示表
turret lathe 大角车床
twill cotton tape 斜纹布带
twill cotton tape 斜纹布带
type test 形式试验
人力资源专业词汇汇总--(中英文)超全
目录 导论:人力资源环境与策略2第一篇设计:工作分析与人力规划5第二篇招聘:人力资源选拔与预测8第三篇开发:人力资源培训与评价12第四篇报酬:薪资方案与福利计划18第五篇影响:员工健康与劳资关系22
导论:人力资源环境与策略 第一章人力资源策略 1.人力资源政策与哲学 。人力资源管理(human resource management ,HRM) 。人力资源管理目标objectives of HRM 。人力资源管理职责duties of HRM 。人力资源管理任务tasks of HRM 。战略性人力资源管理strategic HRM 。人力资源政策human resource policy 。人力资源哲学human resource philosophy 。精神契约psychological contract 。企业认同感organization commitment 2.组织:行为与文化 。正式组织formal organization 。非正式组织informal organization 。组织文化organization culture
。亚文化subculture 。跨文化cross-national culture 。价值观values 。态度attitudes 。角色行为role behavior 。个人主义—集体主义individualism-collectivism 。不确定性规避uncertainty avoidance 。权力距离power distance 。直线和职能职权line and staff authority 3.激励与组织绩效 。激励motivation 。需要层次理论hierarchy of needs theory 。X理论与Y理论theory X & theory Y 。组织体系Ⅰ与组织体系Ⅳsystem Ⅰ& system Ⅳ 。激励-保健理论motivation-hygiene theory 。ERG理论ERG theory 。麦克莱兰德需要理mc-clelland’s theory of needs 。期望理论expectency theory 。公平理论equity theory 。强化理论reinforcement theory 。波特-劳勒期望机率理论borter-lawler’s theory of expectency 第二章人力资源环境
元器件中英文对照
proteus元件库介绍 AND 与门 ANTENNA 天线BATTERY 直流电源 BELL 铃,钟 BVC 同轴电缆接插件BRIDGE 1 整流桥(二极管) BRIDGE 2 整流桥(集成块) BUFFER 缓冲器BUZZER 蜂鸣器 CAP 电容 CAPACITOR 电容CAPACITOR POL 有极性电容CAPVAR 可调电容CIRCUIT BREAKER 熔断丝COAX 同轴电缆 CON 插口 CRYSTAL 晶体振荡器 DB 并行插口 DIODE 二极管 DIODE SCHOTTKY 稳压二极管DIODE VARACTOR 变容二极管
DPY_3-SEG 3段LED DPY_7-SEG 7段LED DPY_7-SEG_DP 7段LED(带小数点) ELECTRO 电解电容 FUSE 熔断器 INDUCTOR 电感 INDUCTOR IRON 带铁芯电感INDUCTOR3 可调电感 JFET N N沟道场效应管 JFET P P沟道场效应管 LAMP 灯泡 LAMP NEDN 起辉器 LED 发光二极管 METER 仪表MICROPHONE 麦克风 MOSFET MOS管 MOTOR AC 交流电机 MOTOR SERVO 伺服电机 NAND 与非门 NOR 或非门 NOT 非门 NPN NPN三极管
NPN-PHOTO 感光三极管OPAMP 运放 OR 或门 PHOTO 感光二极管 PNP 三极管 NPN DAR NPN三极管PNP DAR PNP三极管 POT 滑线变阻器 PELAY-DPDT 双刀双掷继电器RES1.2 电阻 RES3.4 可变电阻RESISTOR BRIDGE ? 桥式电阻RESPACK ? 电阻 SCR 晶闸管 PLUG ? 插头 PLUG AC FEMALE 三相交流插头SOCKET ? 插座 SOURCE CURRENT 电流源SOURCE VOLTAGE 电压源SPEAKER 扬声器 SW ? 开关 SW-DPDY ? 双刀双掷开关
建筑专业词汇中英文对照
建筑专业词汇《中英文对照》~~ 建筑专业词汇 建设,建筑,修建to build, to con struct 建筑学architecture 修筑,建筑物building 房子house 摩天大楼skyscraper 公寓楼block of flats ( 美作:apartment block) 纪念碑monument 宫殿palace 庙宇temple 皇宫,教堂basilica 大教堂cathedral 教堂church 塔,塔楼tower 十层办公大楼ten-storey office block 柱colum n 柱列colonn ade 拱arch 市政town planning ( 美作:city planning) 营建许可证,建筑开工许可证building permission 绿地gree nbelt
建筑物的三面图elevati on 设计图plan 比例尺scale 预制to prefabricate 挖土,掘土excavation 基foun dati ons, base, subgrade 打地基to lay the foundations 砌好的砖歹U course of bricks 脚手架scaffold, scaffolding 质量合格证书certificatio n of fitn ess 原材料raw material 底板bottom plate 垫层cushi on 侧壁sidewall 中心线center line 条形基础strip footing 附件accessories 型辛钢profile steel 钢板steel plate 熔渣slag 飞溅weldi ng spatter 定位焊tacking 弓I弧gen erati ng of arc 熄弧que nching of arc 焊道weldi ng bead 坡口beveled edges 夕卜观检查visual inspection 重皮double-sk in 水平方向弧度radia n in horiz on tai direct ion 成型moldi ng 直线度straightness accuracy 焊缝角变形welding line angular distortion 水平度levelness 铅垂度verticality
中变集团上海变压器有限公司公司简介(中英文对照)
1.1公司简介 中国●中变集团上海变压器有限公司位于上海市金山工业区,与虹桥国际机场、虹桥高铁、浦东国际机场相邻,交通十分便利。 中变集团始建于1985年,历经三十年艰辛创业,跻身于世界发达国家高端变压器制造商行列,主要是公司大胆实行产品技术创新,质量控制,经营理念和战略转型的突破。 公司总占地面积128627平方米,旗下中变集团上海变压器有限公司占地面积56227平方米;员工总数613人,旗下中变集团上海变压器有限公司218人;高级工程师、技术人员74人,旗下中变集团上海变压器有限公司33人;中级工程师、技术人员96人,旗下中变集团上海变压器有限公司45人。 公司在现有技术、人才力量的基础上,还依托上海大学,沈阳变压器研究院作为高尖端产品技术支撑后盾。公司以科学管理创新驱动,推动新技术研发,引进国际国内电气行业最先进的科学成果。目前集团公司技术研发中心,正着手研发利用超导材料生产的变压器作为公司重点开发项目。 公司具有雄厚的技术力量,先进的工装设备。拥有西安启源公司制造的全自动铁芯生产线、测试设备等300多台(套)。最新技术的开发应用,使产品无论从质量还是性能方面都能满足不同用户的个性化需求,并且为用户提供优质的营销和售后服务,以此赢得市场广大用户的好评,使ZBB品牌的信誉转化为市场占有率的提高。多年来公司各项产品的技术经济性能和运行可靠性都处于国内领先地位。 中变集团上海变压器有限公司是国内最大的集产品技术研发、生产制造、市场营销110kV 及以下的电力变压器、特种变压器、电弧炉变、整流变、干式变压器、非晶合金变压器、油浸式(干式)并联电抗器、美式箱变、风力、太阳能光伏变电站等产品的大型生产基地。主要产品38个系列,380个品种,1642个规格,其中油浸式电力变压器年产量7350MVA,干式电力变压器年产量3750MVA,并联电抗器230MVA,美式箱变及风力、太阳能光伏变电站2450MVA。 公司产品广泛应用于国家电网、水力发电、机场码头、工矿企业、化工油田、医疗卫生、环保工程、交通隧道、通信设施等领域。 产品主要销往全国各省、直辖市、自治区电力部门及各类工程项目的建设服务,并远销东南亚,非洲、欧洲等30多个国家和地区。
社会学专业词汇中英文对照
(按中文拼音首字母排序) B 暴民:mob 比拟法:analogical method 比例抽样:proportionate sample 不可知论:agnosticism 变态心理学:abnormal psychology 不完全归纳:incomplete induction 边际效用递减:law of diminishing marginal utility 柏拉图式爱情:Platonic love C 丛众:conformity 残疾人:the handicapped 参考书目:bibliography 参考群体:reference group 成人教育:adult education 初婚年龄:age at first marriage 垂直流动:vertical mobility 出身群体:descent group 抽样误差:sampling error 抽样范围:sampling frame 参与式观察:participant observation D 代沟:generation gap 对照分析:contrastive analysis 定性分析:qualititive analysis 定量分析:quantitative analysis 定额抽样:quota sample 多重人格:multiple personality 地位流动:status mobility 第一手资料:primary data 第二手资料:raw data 单因素实验:single-factor experiment 地域性流动:geographical mobility F 法人:fictitions person 反隔离:desegregation 犯罪学:criminology 父居家庭:patrilocal family 父系亲属:agnate 父子关系:filiation 分析性研究:analytical research 封闭式监管:close custody 封闭型问题:closed question 分层随机抽样:stratified random sample G 规范:norms 更年期:menopause 过激主义:ultraism 个案研究:case study 个人主义:individualism 归属需求:need to belong 个人崇拜:personality cult 功能主义:functionalism H 行话,黑话:argot 横坐标:abscissa 合理趋势:rational trend 霍桑效应:Hawthorne effect 婚姻调适:marriage adjustment 宏观分析:macroscopic analysis 黄金分割:golden section 互补角色:complementary role J 家谱:family religrees 截点:cut-off point 拒答率:refusal rate 绝对值:absolute value 监护人:chaperonage 角色冲突:role conflict 角色距离:role distance 角色紧张:role strain 金钱崇拜:mammon worship 间接暗示:indirect suggestion 价值中立:value free 价值判断:value judgement
变压器中英文对照
变压器常用中英文对照表 材料部分: 线架BOBBIN 铜线WIRE 胶布TAPE 挡墙MARGIN TAPE 套管TUBE/SLEEVE 铁芯CORE 凡立水VARNISH 铜箔COPPER FOIL 胶EPOXY 标签MARKING 吸塑盒CASE 麦拉片FILM 铁氟龙TEFLON 助焊剂FLUX 特性专用名词: 功能损耗POWER LOSS CORE LOSS铁损电感INDUCTANCE 耐压HI-POT 漏感LEAKAGE INDUCTANCE 电压比VOLTAGE RATIO CX电容 电阻DC RESISTANCE 层间短路LAYER SHORT 绝缘阻抗INSULATION RESISTANCE测试条件TEST CONDITION 直流DC 交流AC 规格书上专用名词: 工程变更通知单ECN 材料清单BOM 铁芯胶布包2TSFIX CORE BY MYLAY TAPE 2TS 初级PRI 次级SEC START 卷始卷终FINSH 铜箔反折胶布1.5最小TAPE REVERSE AND BEND WITH 1.5MIN 首件测试FAI 免检STS 作业指导书SOP 先进先出FIFO 剪去CUT OFF 疏绕SPACE 密绕SLOSE 每一百万不良数量DPPM 绕组或绕线WINDING 图面DRAWING 含浸IMPREGNATION 公差TOLERANCE 相位测试PHASE TEST 所有出入线加铁氟龙套管ALL START AND FINISH OF LEAD WIRE ADD TEFLON TUBE 顺时针CLOCKWISE DIRECTION 逆时针COUNTER CLOCKWISE 绕线顺序WINDING SEQUENCE 电路CIRCUIT 绝缘DIELECTRIC 地线DRAIN WIRE 缝隙/研磨GAP 日期DATE 品名ITEM 最大MAX 料号PART NO 客户CUSTOMER 最小MIN 参考值REF 品质专用名词:
财务英文专业词汇
财务会计英文专业词汇 a payment or serious payments 一次或多次付款abatement 扣减 absolute and unconditional payments 绝对和无条件付款 accelerated payment 加速支付 acceptance date 接受日 acceptance 接受 accession 加入 accessories 附属设备 accountability 承担责任的程度 accounting benefits 会计利益 accounting period 会计期间 accounting policies 会计政策 accounting principle 会计准则 accounting treatment 会计处理 accounts receivables 应收账款 accounts 账项 accredited investors 经备案的投资人accumulated allowance 累计准备金acknowledgement requirement 对承认的要求acquisition of assets 资产的取得 acquisitions 兼并 Act on Product Liability (德国)生产责任法action 诉讼 actual ownership 事实上的所有权 additional filings 补充备案 additional margin 附加利差 additional risk附加风险 additions (设备的)附件 adjusted tax basis 已调整税基 adjustment of yield 对收益的调整administrative fee管理费 Administrative Law(美国)行政法 advance notice 事先通知 advance 放款 adverse tax consequences 不利的税收后果advertising 做广告 affiliated group 联合团体 affiliate 附属机构 African Leasing Association 非洲租赁协会after-tax rate 税后利率 aggregate rents 合计租金 aggregate risk 合计风险 agreement concerning rights of explore natural resources 涉及自然资源开发权的协议agreement 协议 alliances 联盟 allocation of finance income 财务收益分配allowance for losses on receivables 应收款损失备抵金 alternative uses 改换用途地使用 amenability to foreign investment 外国投资的易受控制程度 amendment 修改 amortization of deferred loan fees and related consideration 递延的贷款费和相关的报酬的摊销amortization schedule 摊销进度表 amortize 摊销 amount of recourse 求偿金额 amount of usage 使用量 AMT (Alternative Minimum Tax) (美国)可替代最低税 analogous to类推为 annual budget appropriation 年度预算拨款appendix (契约性文件的)附件 applicable law 适用法律 applicable securities laws适用的证券法律applicable tax life 适用的应纳税寿命 appraisal 评估 appraisers 评估人员 appreciation 溢价 appropriation provisions 拨款条例 appropriation 侵占 approval authority 核准权 approval 核准 approximation近似 arbitrary and artificially high value (承租人违约出租人收回租赁物时法官判决的)任意的和人为抬高的价值 arbitration 仲裁 arm's length transaction 公平交易
建筑专业词汇中英对照(精心整理版)
1DESIGN BASIS 设计依据 计划建议书planning proposals 设计任务书design order 标准规范standards and codes 条件图information drawing 设计基础资料basic data for design 工艺流程图process flowchart 工程地质资料engineering geological data 原始资料original data 设计进度schedule of design 2STAGE OF DESIGN 设计阶段 方案scheme, draft 草图sketch 会谈纪要summary of discussion 谈判negotiation 可行性研究feasibility study 初步设计preliminary design 基础设计basic design 详细设计detail design 询价图enquiry drawing 施工图working drawing, construction drawing 竣工图as built drawing 3CLIMATE CONDITION 气象条件 日照sunshine 风玫瑰wind rose 主导风向prevailing wind direction 最大(平均)风速maximum (mean) wind velocity 风荷载wind load 最大(平均)降雨量maximum (mean) rainfall 雷击及闪电thunder and lightning 飓风hurricane 台风typhoon 旋风cyclone 降雨强度rainfall intensity 年降雨量annual rainfall 湿球温度wet bulb temperature 干球温度dry bulb temperature 冰冻期frost period
变压器常用英文术语
变压器常用英文术语(精选) 一,材料名称: 1,线架:BOBBIN 2,磁芯:CORE 3, 胶带:TAPE 4,挡墙胶带:MARGIN TAPE 5,保险丝:FUSE 6,套管:TUBE 7,标签:LABEL 8,环氧树脂:EPOXY 9,铁夹:CLIP 10,底座:BASE 11,盖子:CASE 12,铜箔:COPPER FOIL 13,凡立水:VARNISH 14铜线:COPPER FOIL 15,黑片:ANNEALED 16,引线:LEAD WIRE 17,抽屉式胶芯:SHROUD DOUBLE SECTION 18,白片:NON-ANNEALED 19,矽质套管:SILICON TUBE 19,铁桥:CHANNEL FRAME 20,工字型胶芯:SINGLE SECTION 21,王字型胶芯:DOUBLE SECTION 22,三层绝缘线:TEX-E WIRE 23,丝包线:USTC WIRE 24,绞线:LITZ WIRE 二,常用名词及术语: 1,变压器:TRANSFORMER 2,扼流圈:CHOKE COIL 3,滤波线圈:LINE FILTER 4,逆变器:INVERTER 5,适配器:ADAPTER 6,电木:PHENOLIC 7,初始磁导率:INITIAL PERMEABILITY 8,功率损耗:POWER LOSS 9,密度:DENSITY 10,矫顽力:REMANENCE 11,电感:INDUCTACE 12,电阻:RESISTANCE 14,电压:VOLTAGE 15,电流:CURRENT 16漏电感:LEAKAGE INDUCTACE 16绝缘:INSULATION 17,空载: 18,负载:LOAD 19,CODE:符号,标记 20,圈数:TURN 21,气隙: GAP 22,剪除:CUT OFF 23,品质因素:QUALITY FACTOR 24,浸泡:DIP 25,初级:PRIMARY 26,次级:SECONDARY 27,频率:FREQUENCY 28,输出功率:OUTPUT POWER 29,磁通密度:FLUX DENSITY 30,型号:TYPE 31,尺寸:SIZE 32,绕组:WINDING
人力资源管理专业词汇(中英文对照)
人力资源管理专业词汇( 中英文对照) 人力资源管理:(Human Resource Management ,HRM) 人力资源经理:( human resource manager) 高级管理人员:(executive) 职业:(profession) 道德标准:(ethics) 操作工:(operative employees) 专家:(specialist) 人力资源认证协会:(the Human Resource Certification Institute ,HRCI) 外部环境:(external environment) 内部环境:(internal environment) 政策:(policy) 企业文化:(corporate culture) 目标/使命:(mission) 股东:(shareholders/stakeholder) 非正式组织:(informal organization) 跨国公司:(multinational corporation ,MNC) 管理多样性:(managing diversity) 、工作:(job) 职位:(posting) 工作分析:(job analysis) 工作说明:(job description) 工作规范:(job specification) 工作分析计划表:(job analysis schedule ,JAS) 职位分析问卷调查法:(Management Position Description Questionnaire ,MPDQ) 行政秘书:(executive secretary) 地区服务经理助理:(assistant district service manager) 、人力资源计划:(Human Resource Planning ,HRP) 战略规划:(strategic planning) 长期趋势:(long term trend) 要求预测:(requirement forecast) 供给预测:(availability forecast) 管理人力储备:(management inventory) 裁减:(downsizing) 人力资源信息系统:(Human Resource Information System ,HRIS) 四、招聘:(recruitment) 员工申请表:(employee requisition) 招聘方法:(recruitment methods) 内部提升:(Promotion From Within ,PFW) 工作公告:(job posting) 广告:(advertising) 职业介绍所:(employment agency) 特殊事件:(special events) 实习:(internship) 五、选择:(selection) 选择率:(selection rate)
药理学专业词汇中英文对照
药理学专业词汇(中英文对照) 第一章绪论 药理学 pharmacology 药物 drug 药物效应动力学 pharmacodynamics 药物代谢动力学 pharmacokinetics 上市后药物监测 post-marketing surveillance 第二章药物效应动力学 药物作用 pharmacological action 药理效应 pharmacological effect 治疗作用 therapeutic effect 对症治疗 symptomatic treatment 补充疗法 supplement therapy 不良反应 adverse drug reaction 副作用 side reaction 毒性反应 toxic reaction 后遗效应 after effect 变态反应 allergic reaction 剂量-效应关系 dose-effect relationship 最小有效量 minimal effective dose 最小有效浓度 minimal effective concentration 个体差异 individual variability 效价强度 potency 构效关系 structure activity relationship 激动药 agonist 拮抗药 antagonist 配体门控离子通道受体 ligand gated ion channel receptor 第三章药物代谢动力学 吸收 absorption 首关消除 first-pass elimination 静脉注射 intravenous injection 分布 distribution 生物转化 biotransformation 排泄 excretion 时量关系 time-concentration relationship 生物利用度 bioavailability 药物消除动力学过程 elimination kinetic process 一级消除动力学 first-order elimination kinetics
各种专业名称英语词汇中英文对照表
各种专业名称英语词汇中英文对照表 哲学Philosophy 马克思主义哲学Philosophy of Marxism 中国哲学Chinese Philosophy 外国哲学Foreign Philosophies 逻辑学Logic 伦理学Ethics 美学Aesthetics 宗教学Science of Religion 科学技术哲学Philosophy of Science and Technology 经济学Economics 理论经济学Theoretical Economics 政治经济学Political Economy 经济思想史History of Economic Thought 经济史History of Economic 西方经济学Western Economics 世界经济World Economics 人口、资源与环境经济学Population, Resources and Environmental Economics 应用经济学Applied Economics 国民经济学National Economics 区域经济学Regional Economics 财政学(含税收学)Public Finance (including Taxation) 金融学(含保险学)Finance (including Insurance) 产业经济学Industrial Economics 国际贸易学International Trade 劳动经济学Labor Economics 统计学Statistics 数量经济学Quantitative Economics 中文学科、专业名称英文学科、专业名称 国防经济学National Defense Economics 法学Law
软件工程专业词汇中英对照
软件工程专业词汇中英 对照 The manuscript was revised on the evening of 2021
Acceptance Testing--可接受性测试一般由用户/客户进行的确认是否可以接受一个产品的验证性测试。 actual outcome--实际结果被测对象在特定的条件下实际产生的结果。 Ad Hoc Testing--随机测试测试人员通过随机的尝试系统的功能,试图使系统中断。 algorithm--算法一个定义好的有限规则集,用于在有限步骤内解决一个问题;(2)执行一个特定任务的任何操作序列。 algorithm analysis--算法分析一个软件的验证确认任务,用于保证选择的算法是正确的、合适的和稳定的,并且满足所有精确性、规模和时间方面的要求。 Alpha Testing--Alpha测试由选定的用户进行的产品早期性测试。这个测试一般在可控制的环境下进行的。 analysis--分析分解到一些原子部分或基本原则,以便确定整体的特性;(2)一个推理的过程,显示一个特定的结果是假设前提的结果;(3)一个问题的方法研究,并且问题被分解为一些小的相关单元作进一步详细研究。 anomaly--异常在文档或软件操作中观察到的任何与期望违背的结果。 application software--应用软件满足特定需要的软件。 architecture--构架一个系统或组件的组织结构。 ASQ--自动化软件质量(Automated Software Quality)使用软件工具来提高软件的质量。 assertion--断言指定一个程序必须已经存在的状态的一个逻辑表达式,或者一组程序变量在程序执行期间的某个点上必须满足的条件。assertion checking--断言检查用户在程序中嵌入的断言的检查。 audit--审计一个或一组工作产品的独立检查以评价与规格、标准、契约或其它准则的符合程度。 audit trail --审计跟踪系统审计活动的一个时间记录。 Automated Testing--自动化测试使用自动化测试工具来进行测试,这类测试一般不需要人干预,通常在GUI、性能等测试中用得较多。 Backus-Naur Form--BNF范式一种分析语言,用于形式化描述语言的语法 baseline--基线一个已经被正式评审和批准的规格或产品,它作为进一步开发的一个基础,并且必须通过正式的变更流程来变更。 Basic Block--基本块一个或多个顺
变压器中英文术语
变压器中英文术语-3D Shock 3D 冲击载荷记录器recorder Acc.class 准确级 Acid value(KOH mg/g) 酸值 Acid-base reaction (PH) 酸碱反应 Across the isolating distance of 通过隔离开关isolating switches air gap 空气间隙 Alarm circuit(Upper limit output)报警回路(上限输出)Alarms and tripping 警报和跳闸 along with CT outlet box 出线匣 Altitude 海拔高度 Anti earth-quake grade 耐地震强度Antivibration pad 防震垫 Assembly drawing 装配图 Auxiliary power supply 辅助电源供电 Base Materials 母材 Basic parameter 基本参数 Bellows pipe 波纹管 below the lower transformation 低于下转变温度temperature Bolt 螺栓
Break,Open 断,通Breakdown voltage of the oil 油击穿电压Burden(VA) 负荷 bus 母线Butterfly valve 蝶阀butterfly valve seals 蝶阀密封by Infrared 红外线法by resistance 电阻法 by thermometer 温度计法cabinet for cable connections, 风控箱auxiliary relays and cooling system control,Fan control box cabinets 控制柜Cable Tray Assembly 电缆槽装置cabling 布线capacity on valve side 阀侧容量capacity online side 网侧容量Capacity ratio 容量比Center line of tank 油箱中心线Center of gauge 轨距中心Center of rail 轨道中心Center of supporting plate 支架板中心
元器件中英文对照
p r o t e u s元件库介绍AND 与门 ANTENNA 天线 BATTERY 直流电源 BELL 铃,钟 BVC 同轴电缆接插件 BRIDGE 1 整流桥(二极管) BRIDGE 2 整流桥(集成块) BUFFER 缓冲器 BUZZER 蜂鸣器 CAP 电容 CAPACITOR 电容 CAPACITOR POL 有极性电容 CAPVAR 可调电容 CIRCUIT BREAKER 熔断丝 COAX 同轴电缆 CON 插口 CRYSTAL 晶体振荡器 DB 并行插口 DIODE 二极管 DIODE SCHOTTKY 稳压二极管 DIODE VARACTOR 变容二极管 DPY_3-SEG 3段LED DPY_7-SEG 7段LED DPY_7-SEG_DP 7段LED(带小数点) ELECTRO 电解电容 FUSE 熔断器 INDUCTOR 电感 INDUCTOR IRON 带铁芯电感 INDUCTOR3 可调电感 JFET N N沟道场效应管 JFET P P沟道场效应管 LAMP 灯泡 LAMP NEDN 起辉器 LED 发光二极管 METER 仪表 MICROPHONE 麦克风 MOSFET MOS管 MOTOR AC 交流电机 MOTOR SERVO 伺服电机 NAND 与非门 NOR 或非门
NOT 非门 NPN NPN三极管 NPN-PHOTO 感光三极管 OPAMP 运放 OR 或门 PHOTO 感光二极管 PNP 三极管 NPN DAR NPN三极管 PNP DAR PNP三极管 POT 滑线变阻器 PELAY-DPDT 双刀双掷继电器 电阻 可变电阻 RESISTOR BRIDGE 桥式电阻 RESPACK 电阻 SCR 晶闸管 PLUG 插头 PLUG AC FEMALE 三相交流插头 SOCKET 插座 SOURCE CURRENT 电流源 SOURCE VOLTAGE 电压源 SPEAKER 扬声器 SW 开关 SW-DPDY 双刀双掷开关 SW-SPST 单刀单掷开关 SW-PB 按钮 THERMISTOR 电热调节器 TRANS1 变压器 TRANS2 可调变压器 TRIAC 三端双向可控硅 TRIODE 三极真空管 VARISTOR 变阻器 ZENER 齐纳二极管 DPY_7-SEG_DP 数码管 SW-PB 开关 7407 驱动门 1N914 二极管 74Ls00 与非门 74LS04 非门 74LS08 与门 74LS390 TTL 双十进制计数器 7SEG 4针BCD-LED 输出从0-9 对应于4根线的BCD码
常见材料学专业名词中英文对译
目录 英文缩写词 钢号中所采用的缩写字母及其涵义 常见材料学专业名词中英文对译 对文中使用的英文缩写词说明如下: 缩写英文原文中文翻译 CQ Commercial Quality 普通级 DQ Drawing Quality 冲压级 DDQ Deep Drawing Quality 深冲级 EDDQ Extra Deep Drawing Quality 超深冲级 CSP Compact Srip Production 紧凑式带钢生产 IF Interstitial Free (Steel) 无间隙原子(钢) LC Low Carbon 低碳(钢) DSA Dynamic Strain Aging 动态应变老化 MFS Mean Flow Stress 平均流动应力 YS Yield Stress 屈服应力 DRC Dynamic Recovery 动态回复 DRX Dynamic Recrystallization 动态再结晶 SRX Static Recrystallization 静态再结晶 SRC Static Recovery 静态回复 Ti-IF Ti Interstitial Free (Steel) 含钛无间隙原子(钢) Ti-Nb IF Ti-Nb Interstitial Free (Steel) 含钛铌无间隙原子(钢) ULC Ultra Low Carbon(Steel) 超低碳钢 DSP Direct Strip Production 带钢直接生产 FTSR Flexible Thin Slab Rolling 灵活性薄板坯轧制 C.C.T Continuous Cooling Transformation 过冷奥氏体连续转变曲线 T.T.T Time Temperature Transformation 过冷奥氏体等温转变曲线SPSS Statistical Package for the Social Science 社会科学统计软件包 钢号中所采用的缩写字母及其涵义
人力资源专业词汇汇总 (中英文)超全 整理 的很辛苦的
第一篇导论:人力资源环境与策略第一章人力资源策略 1.人力资源政策与哲学 。人力资源管理(human resource management ,HRM) 。人力资源管理目标 objectives of HRM 。人力资源管理职责 duties of HRM 。人力资源管理任务 tasks of HRM 。战略性人力资源管理 strategic HRM 。人力资源政策 human resource policy 。人力资源哲学 human resource philosophy 。精神契约 psychological contract 。企业认同感 organization commitment 2.组织:行为与文化 。正式组织 formal organization 。非正式组织 informal organization 。组织文化 organization culture 。亚文化 subculture 。跨文化 cross-national culture 。价值观 values 。态度 attitudes 。角色行为 role behavior
。个人主义—集体主义individualism-collectivism 。不确定性规避 uncertainty avoidance 。权力距离 power distance 。直线和职能职权 line and staff authority 3.激励与组织绩效 。激励 motivation 。需要层次理论 hierarchy of needs theory 。X理论与Y理论 theory X & theory Y 。组织体系Ⅰ与组织体系Ⅳ system Ⅰ& system Ⅳ 。激励-保健理论 motivation-hygiene theory 。ERG理论 ERG theory 。麦克莱兰德需要理 mc-clelland’s theory of needs 。期望理论 expectency theory 。公平理论 equity theory 。强化理论 reinforcement theory 。波特-劳勒期望机率理论 borter-lawler’s theory of expectency 第二章人力资源环境 1.人力资源法律环境 。公平就业机会 equal employment opportunity,EEO 。公平就业机会委员会equal employment opportunity commission,EEOC 。实际职业资格 bona fide occupational qualification,BFOQ
统计学专业词汇中英对照
统计学专业词汇中英对照 Absolutedeviation,绝对离差 Absolutenumber,绝对数 Absoluteresiduals,绝对残差 Accelerationarray,加速度立体阵Accelerationinanarbitrarydirection,任意方向上的加速度Accelerationnormal,法向加速度Accelerationspacedimension,加速度空间的维数Accelerationtangential,切向加速度 Accelerationvector,加速度向量 Acceptablehypothesis,可接受假设 Accumulation,累积 Accuracy,准确度 Actualfrequency,实际频数 Adaptiveestimator,自适应估计量 Addition,相加 Additiontheorem,加法定理 Additivity,可加性 Adjustedrate,调整率 Adjustedvalue,校正值 Admissibleerror,容许误差 Aggregation,聚集性 Alternativehypothesis,备择假设 Amonggroups,组间 Amounts,总量 Analysisofcorrelation,相关分析 Analysisofcovariance,协方差分析 Analysisofregression,回归分析 Analysisoftimeseries,时间序列分析 Analysisofvariance,方差分析 Angulartransformation,角转换 ANOVA(analysisofvariance),方差分析 ANOVAModels,方差分析模型 Arcing,弧/弧旋 Arcsinetransformation,反正弦变换 Areaunderthecurve,曲线面积 AREG,评估从一个时间点到下一个时间点回归相关时的误差ARIMA,季节和非季节性单变量模型的极大似然估计Arithmeticgridpaper,算术格纸 Arithmeticmean,算术平均数 Arrheniusrelation,艾恩尼斯关系 Assessingfit,拟合的评估 Associativelaws,结合律