最全模具行业相关联中英文对照!没有之一

最全模具行业相关联中、英文对照！没有之一

dowel pin 定位梢draft 拔模锥度draw bead 张力调整杆drive bearing 传动轴承ejection pad 顶出衬垫ejector 脱模器ejector guide pin 顶出导梢ejector leader busher 顶出导梢衬套ejector pad 顶出垫ejector pin 顶出梢ejector plate 顶出板ejector rod 顶出杆ejector sleeve 顶出衬套ejector valve 顶出阀eye bolt 环首螺栓filling core 椿入蕊film gate 薄膜形浇口finger pin 指形梢finish machined plate 角形模板finish machined round plate 圆形模板fixed bolster plate 固定侧模板flanged pin 带凸缘销flash gate 毛边形浇口flask 上箱floating punch 起浮冲头gate 浇口gate land 浇口面gib 凹形拉紧楔goose neck 鹅颈管guide bushing 引导衬套guide pin 导梢guide post 引导柱guide plate 导板guide rail 导轨head punch 顶头冲孔headless punch 直柄冲头heavily tapered solid 全体模蕊盒hose nippler 管接头impact damper 缓冲器injection ram 压射柱塞inlay busher 嵌入衬套inner plunger 内柱塞inner punch 内冲头insert 嵌件insert pin 嵌件梢king pin 转向梢king pin bush 主梢一、入水：gate进入位：gate location 水口方式：gate type大水口：edge gate细水口：pin-point gate水口巨细：gate size转水口：switching runner/gate

唧嘴口径：sprue diameter二、流道: runner暖流道：hot runner,hot manifold热嘴冷流道: hot sprue/cold runner唧嘴直流: direct sprue gate圆形流道：round(full/half runner流道电脑剖析：mold flow analysis流道平衡:runner balance 热嘴：hot sprue暖流道板：hot manifold发热管：cartridge heater探针: thermocouples插头：connector plug插座：connector socket密封/封料：seal三、运水：water line喉塞：line lpug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socker四、模具零件：mold components三板模：3-plate mold二板模：2-plate mold边钉/导边：leader pin/guide pin边司/导套：bushing/guide bushing中托司：shoulder guide bushing中托边L：guide pin 顶针板：ejector retainner plate托板：support plate螺丝：screw管钉：dowel pin开模槽：ply bar scot内模管位：core/cavity inter-lock顶针：ejector pin司筒：ejector sleeve司筒针：ejector pin推板：stripper plate缩呵：movable core,return core core puller扣机（尼龙拉勾）：nylon latch lock斜顶：lifter模胚（架）：mold base上内模：cavity insert 下内模：core insert行位（滑块）：slide镶件：insert压座/斜鸡：wedge耐磨板/油板：wedge wear plate压条：plate 撑头: support pillar唧嘴：sprue bushing挡板：stop plate 定位圈：locating ring锁扣：latch扣鸡：parting lock set推

杆：push bar栓打螺丝：S.H.S.B顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush废物钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring中托司：ejector guide bush中托边：ejector guide pin镶针：pin销子：dowel pin波子弹弓：ball catch喉塞: pipe plug锁模块：lock plate斜顶：angle from pin斜顶杆：angle ejector rod 尼龙拉勾：parting locks活动臂：lever arm复位键、提早回杆：early return bar气阀：valves斜导边：angle pin术语：terms承压平面平衡：parting surface support balance模排气：parting line venting回针碰料位：return pin and cavity interference模总高超出啤机标准：mold base shut hight顶针碰运水：water line interferes withejector pin料位出上/下模：part from cavith (core) side模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate.禁绝用镶件：Do not use (core/cavity) insert用铍铜做镶件：use beryllium copper insert开始（正式）模图规划：preliinary (final) mold design反呵：reverse core弹弓紧缩量：spring compressed length稳定性好：good stability,stable强度不够：insufficient rigidity均匀冷却：even cooling扣模：sticking 热膨胀：thero expansion公役：tolorance铜公(电极）：copper electrodedowel pin 定位梢draft 拔模锥度draw bead 张力调整杆drive bearing 传动轴承ejection pad 顶出衬垫

ejector 脱模器ejector guide pin 顶出导梢ejector leader busher 顶出导梢衬套ejector pad 顶出垫ejector pin 顶出梢ejector plate 顶出板ejector rod 顶出杆ejector sleeve 顶出衬套ejector valve 顶出阀eye bolt 环首螺栓filling core 椿入蕊film gate 薄膜形浇口finger pin 指形梢finish machined plate 角形模板finish machined round plate 圆形模板fixed bolster plate 固定侧模板flanged pin 带凸缘销flash gate 毛边形浇口flask 上箱floating punch 起浮冲头gate 浇口gate land 浇口面gib 凹形拉紧楔goose neck 鹅颈管guide bushing 引导衬套guide pin 导梢guide post 引导柱guide plate 导板guide rail 导轨head punch 顶头冲孔headless punch 直柄冲头heavily tapered solid 全体模蕊盒hose nippler 管接头impact damper 缓冲器injection ram 压射柱塞inlay busher 嵌入衬套inner plunger 内柱塞inner punch 内冲头insert 嵌件insert pin 嵌件梢king pin 转向梢king pin bush 主梢difference quantity差异量cause analysis原因剖析raw materials质料materials物料finished product制品semi-finished product半制品packing materials包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub库房on way location在途仓oversea location海外仓spare parts

physical inventory list备品盘点清单spare molds location 模具备品仓skid/pallet栈板tox machine自铆机wire EDM 线割EDM放电机coil stock卷料sheet stock片料tolerance 工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg打开图radius半径shim(wedge)楔子torch-flame cut 火焰切开set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate 绷簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability才能parameter参数factor系数phosphate 皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting 顶固模demagnetization去磁;消磁high-speed transmission 高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision 版次part number/P/N料号good products良品scraped

products报定心品defective products不良品finished products制品disposed products处理品barcode条形码flow chart流程窗体assembly组装stamping冲压molding 成型spare parts=buffer备品coordinate坐标dismantle the die折模auxiliary fuction辅佐功用poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光

response=reaction=interaction感应ram连杆edge finder 巡边器concave 凹convex凸short射料不足nick缺口speck瑕疪shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit 沙砾granule=peuet=grain细粒grit maker抽粒机cushion 缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill钻boring镗blinster气泡fillet镶;嵌边through-hole form通孔方式voller pin formality滚针方式cam driver铡楔shank摸柄crank shaft 曲柄轴augular offset角度误差velocity速度production tempo出产进展现状torque扭矩spline=the multiple keys 花键quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel钨

高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance 电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机模具工程类plain die简易模pierce die冲孔模forming die成型模progressive die接连模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸)draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark 冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking 下料stamp letter冲字(料号)shearing剪断tick-mark nearside正面压印tick-mark farside不和压印冲压称号类extension dwg打开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification 冲床标准die height range适用模高die height闭模高度burr 毛边gap空隙weight分量total wt.总分量punch wt.上模分量五金零件类inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring绷簧lifter pin 顶料销eq-height sleeves=spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线绷簧outer guiding post外导柱stop screw止付螺丝located pin定位销

outer bush外导套模板类top plate上托板（顶板）top block 上垫脚punch set上模座punch pad上垫板punch holder

上夹板stripper pad脱料背板up stripper上脱料板male die 公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder 下夹板die set下模座bottom block下垫脚bottom plate下托板(底板)stripping plate内外打(脱料板)outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板零件类punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block 折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate 气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch 压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块101个热处理常用英文词汇1. indication 缺点2. test specimen 试样3. bar 棒材4. stock 质料5. billet 方钢，钢方坯6. bloom 钢坯,钢锭7. section 型材8. steel ingot 钢锭9. blank 坯料，半制品10. cast steel 铸钢11. nodular cast iron 球墨铸铁12. ductile cast iron 球墨铸铁13. bronze 青铜14. brass 黄铜15. copper 合金16.

stainless steel不锈钢17. decarburization 脱碳18. scale 氧化皮19. anneal 退火20. process anneal 进行退火21. quenching 淬火22. normalizing 正火23. Charpy impact text 夏比冲击实验24. fatigue 疲惫25. tensile testing 拉伸实验26. solution 固溶处理27. aging 时效处理28. Vickers hardness维氏硬度29. Rockwell hardness 洛氏硬度30. Brinell hardness 布氏硬度31. hardness tester硬度计32. descale 除污，除氧化皮等33. ferrite 铁素体34. austenite 奥氏体35. martensite马氏体36. cementite 渗碳体37. iron carbide 渗碳体38. solid solution 固溶体39. sorbite 索氏体40. bainite 贝氏体41. pearlite 珠光体42. nodular fine pearlite/ troostite屈氏体43. black oxide coating 发黑44. grain 晶粒45. chromium 铬46. cadmium 镉47. tungsten 钨48. molybdenum 钼49. manganese 锰50. vanadium 钒51. molybdenum 钼52. silicon 硅53. sulfer/sulphur 硫54. phosphor/ phosphorus 磷55. nitrided 氮化的56. case hardening 外表硬化，外表淬硬57. air cooling 空冷58. furnace cooling 炉冷59. oil cooling 油冷60. electrocladding /plating 电镀61. brittleness 脆性62. strength 强度63. rigidity 刚性,刚度64. creep 蠕变65. deflection 挠度66. elongation 延伸率67. yield strength 屈从强度68. elastoplasticity 弹塑性69. metallographic

structure 金相安排70. metallographic test 金相实验71. carbon content 含碳量72. induction hardening 感应淬火73. impedance matching 感应淬火74. hardening and tempering 调质75. crack 裂纹76. shrinkage 缩孔，疏松77. forging 锻（件）78. casting 铸（件）79. rolling 轧（件）80. drawing 拉（件）81. shot blasting 喷丸（处理）82. grit blasting 喷钢砂（处理）83. sand blasting 喷砂（处理）84. carburizing 渗碳85. nitriding 渗氮86. ageing/aging 时效87. grain size 晶粒度88. pore 气孔89. sonim 夹砂90. cinder inclusion 夹渣91. lattice晶格92.

abrasion/abrasive/rub/wear/wearing resistance (property) 耐磨性93. spectrum analysis光谱剖析94. heat/thermal treatment 热处理95. inclusion 夹杂物96. segregation 偏析97. picking 酸洗，酸浸98. residual stress 剩余应力99. remaining stress 剩余应力100. relaxation of residual stress 消除剩余应力101. stress relief 应力开释机械类常用英语：冲压模具-零件类punch冲头insert入块(嵌入

件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate 挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶

杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中心板spring box绷簧箱spring-box eject-rod绷簧箱顶杆

spring-box eject-plate绷簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块landed plunger mold 有肩柱塞式模具burnishing die 挤光模landed positive mold 有肩全压式模具button die 镶入式圆形凹模loading shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模loose mold 活动式模具clod hobbing 冷揉捏制模louvering die 百叶窗冲切模composite dies 复合模具manifold die 分歧管模具counter punch 反凸模modular mold 组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模offswt bending die 双折冷弯模具extrusion die 挤出模palletizing die 叠层模family mold 反套制品模具plaster mold 石膏模blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具fantail die 扇尾形模具pressure

die 压紧模fishtail die 鱼尾形模具profile die 轮廓模flash mold 溢料式模具progressive die 次序模gypsum mold 石膏铸模protable mold 手提式模具hot-runner mold 暖流道模具prototype mold 雏形实验模具ingot mold 钢锭模punching die 落料模lancing die 切断模aising(embossing) 压花崎岖成形re-entrant mold 倒角式模具sectional die 拼合模runless injection mold 无流道冷料模具sectional die 对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套single cavity mold 单腔模具solid forging die 全体锻模split forging die 拼合锻模split mold 双并式模具sprueless mold 无注道残料模具squeezing die 揉捏模stretch form die 拉伸成形模sweeping mold 平刮铸模swing die 振荡模具three plates mold 三片式模具trimming die 切边模unit mold 单元式模具universal mold 通用模具unscrewing mold 退扣式模具yoke type die 轭型模塑料成形模具mould for plastics热塑性塑料模mould for thermoplastics热固性塑料模mould for thermosets紧缩模compression mould压注模、传递模transfer mould打针模injection mould热塑性塑料打针模injection mould for thermoplastics热固性塑料打针模injection mould for thermoses成形零件定模stationary mould fixed half动模movable mould moving half定模

座板fixed clamp plate, top clamping plate. top plate动模座板moving clamp plate. bottom clamping plate. bottom plate上模座板upper clamping plate下模座板lower clamping plate凹模固定板cavity-retainer plate 型芯固定板core-retainer plate凸模固定板

punch-retainer plate模套chase. bolster. frame支承板backing plate. supprr plate垫块spacer parallel支架ejector housing. mould base leg模具工程常用词汇英汉对照die 模具figure file, chart file图档cutting die, blanking die冲裁模progressive die, follow (-on)die接连模compound die复合模punched hole冲孔panel board镶块to cutedges=side cut=side scrap切边to bending折弯to pull, to stretch拉伸Line streching, line pulling线拉伸engraving, to engrave刻印upsiding down edges翻边to stake铆合designing, to design规划design modification规划改变die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board 模板padding block垫块stepping bar垫条upper die base 上模座lower die base下模座upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品spring 绷簧bolt螺栓document folder文件夹file folder资料夹to put file in order收拾资料spare tools location手工备

品仓first count初盘人first check初盘复棹人second count 复盘人second check复盘复核人equipment设备waste materials废料work in progress product在制品casing = containerazation装箱quantity of physical invetory second count 复盘点数量quantity of customs count会计师盘,点数量the first page第一联filed by accounting department for reference会计部存查end-user/using unit(department)运用单位summary of year-end physical inventory bills年终盘点截止单据汇总表bill name单据称号This sheet and physical inventory list will be sent to accountingdepartment together (Those of NHK will be sent to financialdepartment)本表请与盘点清册一同送会计部－(NHK厂区送财会部)Application status records of year-end physical inventory List andphysical inventory card 年终盘点卡与清册运用－情况明细表blank and waste sheet NO.空白与作废单号plate电镀mold成型material for engineering mold testing工程试模资料not included in physical inventory不列入盘点sample 样品incoming material to be inspected进货待验description品名steel/rolled steel钢材material statistics sheet物料计算明细表meeting minutes会议记录meeting type 会别distribution department分发单位location地址chairman主席present members到会人员subject主题

conclusion定论decision items抉择事项responsible department担任单位pre-fixed finishing date预定完成日approved by / checked by / prepared by核准/审阅/承办PCE assembly production schedule sheetPCE组装厂出产排配表model机锺work order工令revision版次remark补白production control confirmation出产承认checked by初审approved by核准department部分stock age analysis sheet库存货龄剖析表on-hand inventory现有库存available material良品可运用obsolete material良品已呆滞to be inspected or reworked待验或重工total算计cause description原因阐明part number/ P/N 料号type形态

item/group/class类别quality质量prepared by制表notes 阐明year-end physical inventory difference analysis sheet 年终盘点差异剖析表physical inventory盘点数量physical count quantity帐面数量difference quantity差异量cause analysis原因剖析raw materials质料materials物料finished product制品semi-finished product半制品packing materials包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub库房on way location在途仓oversea location海外仓spare parts physical inventory list备品盘点清单spare molds location

模具备品仓skid/pallet栈板tox machine自铆机wire EDM 线割EDM放电机coil stock卷料sheet stock片料tolerance 工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg打开图radius半径shim(wedge)楔子torch-flame cut 火焰切开set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate 绷簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability才能parameter参数factor系数phosphate 皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting 顶固模demagnetization去磁;消磁

塑胶模具类中英文对照专业术语

塑胶模具类中英文对照专业术语工程部/ Design department: 1) Designer - 设计师。 2) Assembly drawing - 模具组装图。 3) Mold layout - 模具结构图。 4) 2D product drawing - 2D产品图。 5) 3D product data - 3D产品数据。 6) Part drawing - 散件图。 7) Insert molding - 镶件模。 8) 2 color mold / Double injection tool - 双色模。 9) Hydraulic system - 油/水压系统。 10) Parting line - 分模线。 11) Air venting - 排气槽。 12) Cooling system - 冷却系统。 13) Screw - 镙丝。 14) Hot runner system - 热流道。 15) Valve gate - 伐针入水口。 16) Fan gate - 扇型入水口。 17) Pin point gate - 针点进胶。 18) Moon gate / Banana gate - 香蕉，象牙入水口。 19) Submarine gate - 潜水口。 20) Injection machine tonnage - 注塑机吨数。 21) Number of cavity - 穴数。 22) Steel - 钢材。 23) Copper - 铜。 24) Tungsten copper - 钨铜。 25) Beryllium copper - 铍铜。 26) Hardening - 加硬/淬火。 27) Tempering - 回火。

模具方面的中英文对照

模具方面的中英文对照【二】 2007-05-09 22:35 塑料成型模具的主要设计要素脱模距 stripper distance 脱模斜度 draft 投影面积 projected area 最大开距 maximum daylight; open daylight 闭合高度 mould-shut height 抽芯距 core-pulling distance 抽芯力 core-pulling force 脱模力 ejector force 开模力 mould opening force 模内压力 internal mould pressure; cavity pressure 成型压力 moulding pressure 背压环 back-up ring 1 bar = 14.5psi 高压接头 bite type fitting 液压马达 hydraulic motor 冷却水流量计 waterflow regulator 打磨器材 abrasive material 打磨砂轮 grinding wheels 切割砂轮 cutting wheels 码模夹(注塑机使用) mould clamps; lifting clamps 小五金工具 piping tools 高压力软管 high pressure hose 风管,水软管 air .water hose 高压油表 pressure gauge 压力油喉 hydraulic hoses 光塑检测 photoelastic testing 吹塑模 plastic blow mould 注塑模 plastic injection mould 冲扎复合模 blank & form compound die 精密冲模 precision blanking die 熔料流动率 MFR=melt flow rate 熔料流动指数 MET=melt flow index 推板导柱 guide pin for ejector plater 座板 clamping plate 垫块 space block(plate) 推板 ejector block(plate) afdek plate 档尘板 guide stripe 行位后板 cavity sub-insert 前模镶件 core sub-insert 后模镶件 sprue puller insert 扣针镶件

常用模具零件中英文对照表

常用模具零件中英文对照表 2005-12-19 14:51:17中国注塑网一、入水：gate 进入位：gate location 水口形式：gate type 大水口：edge gate 细水口：pin-point gate 水口大小：gate size 转水口：switching runner/gate 唧嘴口径：sprue diameter 二、流道: runner 热流道：hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形流道：round(full/half runner 流道电脑分析：mold flow analysis 流道平衡:runner balance 热嘴：hot sprue 热流道板：hot manifold 发热管：cartridge heater 探针: thermocouples 插头：connector plug 插座：connector socket 密封/封料：seal 三、运水：water line 喉塞：line lpug 喉管：tube 塑胶管：plastic tube 快速接头：jiffy quick connector plug/socker 四、模具零件：mold components 三板模：3-plate mold 二板模：2-plate mold 边钉/导边：leader pin/guide pin 边司/导套：bushing/guide bushing 中托司：shoulder guide bushing 中托边：guide pin 顶针板：ejector retainner plate 托板：support plate 螺丝：screw 管钉：dowel pin

模具术语(中英文对照)

AD-Diameter The tread diameter at the centerline of the tread (EU); also: "T-Diameter"(GT) AD直径：指胎面中心线直径（EU）。又叫T直径（GT） Auto-lock Ear A Lug on the cone ring used to mount the mold/container in the top half of a 60“ NRM Auto-lock press. 导环上的突缘，用于和60“ NRM Auto-lock 硫化机上半部连接。 Bead Ring The tire bead forming ring (also: toe ring) 钢圈，也称toe ring Bead Ring Register The landing and tapered seat that the bead ring fits into 钢圈配合：侧板上，和钢圈配合的平面及锥面 Bottom Container Plate The plate that the bottom sidewall plate is bolted to 模壳底座 Bottom Container Plate Lifting Lug A lug attached to the Bottom Container Plate with Horizontal holes used for lifting. 模壳底座吊耳：装配在底座上、有水平的孔，用来吊装的吊耳 Bottom Container Plate Dowel Pin Lug A lug attached to the Bottom Container Plate that supports the Dowel Pin Bushing. 装配在底座上，用来支承定位销套的突缘 Bottom Container Plate Hold Down A lug that is used to fix the Bottom Plate in the Press. 用来将底座装配在硫化机上的突缘 Breaker Hook A hook fixed to the bottom of the tread segment that catches the bottom container plate only when the segment will not release from the tire during de-molding. 分离钩：固定在花纹块底部的钩子，轮胎硫化完后若花纹块不能跟轮胎分离，就用此钩抓住模壳底座帮助花纹块和轮胎进行分离。

模具DFM常用中英文对照

DFM常用中英文对照 1、这个红色面在前模方向/后模方向/行位方向有倒扣。 This red surface is undercut at cavity side / core side / slider side. 2、这些红色面在前模方向/后模方向/行位方向有倒扣。 These red surfaces are undercut at cavity side / core side / slider side. 3、产品的这个位置太小，导致模具在前模方向/后模方向/行位方向有薄钢位。 This position is too small and it will bring the thin steel at cavity side / core side / slider side. 4、这些红色线是前后模/镶件/行位/斜顶分型线。 These red lines are the parting line of cavity and core / insert / slider / lifter. 5、此产品使用推板/推块顶出。 Use the stripper plate / ejector block to eject this part. 6、前模/后模斜内行位。 Inner angle slider at cavity / core side. 7、为了简化模具结构建议改变此处出模方向。 Suggest to change the draft direction of this position to make the mold structure simply. 8、最终的进胶位置根据模流分析。 Finally gate position according the mold flow analysis. 9、斜顶与后面的柱位空间太小，斜顶在运动时会干涉到柱子，请考虑移动这个柱子的位置。 This lifter intervene with the pole during ejection, please consider changing the position of the pole. 10、此处有薄钢位，强度不足而且不容易冷却。 The strength of this area is too weak and it is hard to cool because the thin steel. 11、此处有尖角，填充困难。 It is hard to fill for this area because the sharp feature. 12、此处料位太厚，会有缩水，建议减胶改善。 We suggest to reduce some wall thickness to avoid the sink mark for this position. 13、此处的行位夹线在外观面上，请确认是否接受？ Please confirm whether it is acceptable to have a slider line on the visible surface? 14、建议加大拔模角，以便脱模顺利。 We suggest to enlarge the draft angle to help release the tool. 15、如果分型面此处，模具上会有尖角和刀口，对模具寿命有影响。 There are sharp edges if we set the parting line here, it will reduce the tool life. 16、此处料厚段差很大，成品表面会有应力痕，建议修改如图示。 The thickness is not equal and it will bring the stress lines on the surface, suggest to improve the part as the picture shown. 17、此大行位上有小行位，开模时小行位需先退，大行位做延时，合模时则相反。 The small slider is inside the big slider, when the mold open, the small slider need to recede first and the big slider have to postpone. When the mold close, it is contrary. 18、此处需做强顶。 This position need to force ejection. 19、由于此处没有足够空间下热咀，所以需做一个柱子进胶。 This position need to make a pole for gating because there have no enough space for hot sprue. 20、沾模， stick

模具--中英文对照

guide bushing 引导衬套 guide pin 导梢 guide post 引导柱 guide plate 导板 guide rail 导轨 head punch 顶头冲孔 headless punch 直柄冲头 heavily tapered solid 整体模蕊盒hose nippler 管接头 impact damper 缓冲器 injection ram 压射柱塞 inlay busher 嵌入衬套 inner plunger 内柱塞 inner punch 内冲头 insert 嵌件 insert pin 嵌件梢 king pin 转向梢 king pin bush 主梢一、入水：gate 进入位：gate location 水口形式：gate type 大水口：edge gate 细水口： pin-point gate 水口大小：gate size 转水口：switching runner/gate 唧嘴口径：sprue diameter 二、流道: runner 热流道：hot runner, hot manifold 热嘴冷流道: hot sprue/cold runner

模具中英文对照表

landed plunger mold 有肩柱塞式模具burnishing die 挤光模 landed positive mold 有肩全压式模具button die 镶入式圆形凹模 loading shoe mold 料套式模具 center-gated mold 中心浇口式模具loose detail mold 活零件模具 chill mold 冷硬用铸模 loose mold 活动式模具 clod hobbing 冷挤压制模 louvering die 百叶窗冲切模composite dies 复合模具 manifold die 分歧管模具 counter punch 反凸模 modular mold 组合式模具 double stack mold 双层模具 multi-cavity mold 多模穴模具electroformed mold 电铸成形模 multi-gate mold 复式浇口模具expander die 扩径模 offswt bending die 双折冷弯模具extrusion die 挤出模

palletizing die 叠层模 family mold 反套制品模具 plaster mold 石膏模 blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具 fantail die 扇尾形模具 pressure die 压紧模 fishtail die 鱼尾形模具 profile die 轮廓模 flash mold 溢料式模具progressive die 顺序模 gypsum mold 石膏铸模 protable mold 手提式模具 hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模 punching die 落料模 lancing die 切口模 raising(embossing) 压花起伏成形re-entrant mold 倒角式模具

模具常用术语中英文对照表

"R，L Co.,Ltd" 模具常用术语中英文对照模芯Parting Core 局部视图Partial View 冷料# Cold Slag 线切割 Wire 轮廊Contour 螺纹孔 Tapping Hole 连接件 Fittings 斜针Angle Pin 接合Engage 替换镶件Interchangeable Mold Inserts 指定吨位的注塑机Specific Press 水嘴接头Water Fittings 螺纹Eyebolt Thread 回针Stop Pin 二级顶出针Sub-Leaderd Pin 镶件Mold Insert 加硬Harden 唧嘴Sprue 设计筒图Design Preliminary 名称块表Title Block 版本标识Revision Level 材料清单Stock List 制模Build Mold 手动滑块Hand Slide 漏水测试Leak Test 流道排气Runner Vents 抛光Draw Polish 侧抽芯 Side Action 加强筋 Reinforcing

三角撑 Gusset 柱子Bossed 出模斜度Draft 外廊Contour 落单会议Kick-Off Meeting 装卸孔 Handling Hole 运输安全带Moldstrap 码模槽 Clamp Slot 撑头Support Pillar 螺牙1/2-13 Eye Bolt 1/2-13Tap 导柱位 Leader Pin Location 耐落胶 Teflon Paste 偏移量 Offset 水塞Water Line Plug 撬模脚 Ppy Slot 重新加工Reworked 配件Components 补偿Compensation 平面度 Parallel 倒角Chamfer 模胚Mold Base 热嘴Hotnozzle 火花机 Edm 熔接线 Weildline 压机Press 晒纹Texturing 梯形Trapezoid 凸缘、法兰Flange 方铁Spacer Block 顶针板Ejector Plate 顶针底板Ejector Retainer Plate 垫板Retainer Plate

模具方面的中英文对照

查看文章模具方面的中英文对照【二】2007-05-09 22:35 塑料成型模具的主要设计要素脱模距stripper distance 脱模斜度draft 投影面积projected area 最大开距maximum daylight;open daylight 闭合高度mould-shut height 抽芯距core-pulling distance 抽芯力core-pulling force 脱模力ejector force 开模力mould opening force 模内压力internal mould pressure;cavity pressure 成型压力moulding pressure 背压环back-up ring 1 bar = 14.5psi 高压接头bite type fitting 液压马达hydraulic motor 冷却水流量计waterflow regulator 打磨器材abrasive material 打磨砂轮grinding wheels 切割砂轮cutting wheels 码模夹（注塑机使用） mould clamps; lifting clamps 小五金工具piping tools 高压力软管high pressure hose 风管,水软管air .water hose 高压油表pressure gauge 压力油喉hydraulic hoses 光塑检测photoelastic testing 吹塑模plastic blow mould 注塑模plastic injection mould 冲扎复合模blank & form compound die 精密冲模precision blanking die 熔料流动率MFR=melt flow rate 熔料流动指数MET=melt flow index 推板导柱guide pin for ejector plater 座板clamping plate 垫块space block(plate) 推板ejector block(plate) afdek plate 档尘板guide stripe 行位后板cavity sub-insert 前模镶件core sub-insert 后模镶件sprue puller insert 扣针镶件 stage ejector 顶棍

模具DFM常用中英文对照

DFM常用中英文对照 15、如果分型面此处，模具上会有尖角和刀口，对模具寿命有影响。. There are sharp edges if we set the parting line here, it will reduce the tool life. 16、此处料厚段差很大，成品表面会有应力痕，建议修改如图示。. The thickness is not equal and it will bring the stress lines on the surface, suggest to improve the part as the picture shown. 17、此大行位上有小行位，开模时小行位需先退，大行位做延时，合模时则相反。. The small slider is inside the big slider, when the mold open, the small slider need to recede first and the big slider have to postpone. When the mold close, it is contrary. 18、此处需做强顶。. This position need to force ejection. 19、由于此处没有足够空间下热咀，所以需做一个柱子进胶。. This position need to make a pole for gating because there have no enough space for hot sprue. 20、沾模， Stick 1.High shrinkage values could indicate sink marks or voids at gate location 高缩水率的产品容易产生缩印，但在浇口附近可以避免。. 2.Welding line on the cosmetic surface 熔接线在外表面 3.Two banana gate was to being confluent in the end of melt flow. 两个香蕉浇口在流动未端熔合。. 4.Venting insert here has flash 排气镶件处有飞边 5.Venting gap between inserts is too big 镶件处的排气槽过大 6.Stress mark on the cosmetic surface 产品外表面上有压痕 7.Uneven thickness 不平均的产品壁厚 8.Unreasonable product structure 不合理的产品结构 9.Injection speed is high 注塑压力过高 10.There is black spot on the cosmetic surface 产品外表面上有黑色点 11.There is flash on the product 产品有飞边 12.there is sink mark on the cosmetic surface 产品外表面上有缩痕 13.Gate size is not reasonably 浇口尺寸不合理 14.There is argent spot 这里有亮点（银色斑点） 15.The plastic of first shot didn't meet high temperature. 塑料的第一胶不会有很高的温度。. 16.Make sure the core float plate was closed before lifter completely return to correct position 确认lifter完全回位时core侧浮动板已经复位 17.Make sure the ejector system is smooth 确认顶针系统移动平稳 18.Add early return structure to protect lifter return to correct position 增加先复位机构保护lifter回到正确位置。. 19.Propose to add draft on slider side wall and draw polish. 建议增加slider的角度和抛光角度。. 20.It is too thin and very difficult to inject fully, and weakness wall will have risk of the part function 该处壁厚过薄而造成很难去填充完整，薄壁将会有产品功能上的风险。. 21.These are will have sink marks due to uneven thickness, propose to reduce plastic. 壁厚不均匀容易产生缩印，建议在该处减胶。. 22.These are will have sink marks due to ribs opposite. 正面的筋位易导致背面产生缩印。. 23.Please confirm the 3D part thickness whether has including painting thickness or not? 请确认产品的设计是否考虑到油漆的厚度。.

模具方面的中英文对照

查看文章模具方面的中英文对照【二】 2007-05-09 22:35 塑料成型模具的主要设计要素脱模距stripper distance 脱模斜度draft 投影面积projected area 最大开距maximum daylight;open daylight 闭合高度mould-shut height 抽芯距core-pulling distance 抽芯力core-pulling force 脱模力ejector force 开模力mould opening force 模内压力internal mould pressure;cavity pressure 成型压力moulding pressure 背压环back-up ring 1 bar = 14.5psi 高压接头bite type fitting 液压马达hydraulic motor 冷却水流量计waterflow regulator 打磨器材abrasive material 打磨砂轮grinding wheels 切割砂轮cutting wheels 码模夹（注塑机使用） mould clamps; lifting clamps 小五金工具piping tools 高压力软管high pressure hose 风管,水软管air .water hose 高压油表pressure gauge 压力油喉hydraulic hoses 光塑检测photoelastic testing 吹塑模plastic blow mould 注塑模plastic injection mould 冲扎复合模blank & form compound die 精密冲模precision blanking die 熔料流动率MFR=melt flow rate 熔料流动指数MET=melt flow index 推板导柱guide pin for ejector plater 座板clamping plate 垫块space block(plate) 推板ejector block(plate) afdek plate 档尘板guide stripe 行位后板cavity sub-insert 前模镶件core sub-insert 后模镶件sprue puller insert 扣针镶件 stage ejector 顶棍 spacer rock(risers) 间隔板变形distortion 弯曲

模具英文缩写对照

模芯 Parting Core 局部视图 Partial View 冷料# Cold Slag 线切割 Wire E.D.M 轮廊 Contour 螺纹孔 Tapping Hole 连接件 Fittings 斜针 Angle Pin 接合 Engage 替换镶件 Interchangeable Mold Inserts 指定吨位的注塑机 Specific Press 水嘴接头 Water Fittings 螺纹 Eyebolt Thread 回针 Stop Pin 二级顶出针 Sub-Leaderd Pin 镶件 Mold Insert 加硬 Harden Sprue唧嘴 Design Preliminary 设计筒图Title Block名称块表 Revision Level版本标识 Stock List 材料清单Build Mold制模 Hand Slide手动滑块 Leak Test 漏水测试Runner Vents 流道排气Draw Polish抛光Side Action侧抽芯 Reinforcing加强筋 Gusset三角撑 Bossed柱子 Draft出模斜度 Contour外廊 Kick-Off Meeting落单会议 Handling Hole装卸孔运输安全带 Moldstrap 码模槽 Clamp Slot 撑头 Support Pillar 螺牙 1/2-13 Eye Bolt 1/2-13Tap 导柱位 Leader Pin Location 耐落胶 Teflon Paste 偏移量 Offset Water Line Plug水塞Ppy Slot 撬模脚重新加工 Reworked 配件 Components 补偿 Compensation 平面度 Parallel 倒角 Chamfer

模具常用中英文对照

模具常用术语中英文对照模芯Parting Core 局部视图Partial View 冷料# Cold Slag 线切割 Wire E.D.M 轮廊Contour 螺纹孔 Tapping Hole 连接件 Fittings 斜针Angle Pin 接合Engage 替换镶件Interchangeable Mold Inserts 指定吨位的注塑机Specific Press 水嘴接头Water Fittings 螺纹Eyebolt Thread 回针Stop Pin 二级顶出针 Sub-Leaderd Pin 镶件Mold Insert 加硬Harden 唧嘴Sprue 设计筒图Design Preliminary 名称块表Title Block 版本标识Revision Level

材料清单Stock List 制模Build Mold 手动滑块Hand Slide 漏水测试Leak Test 流道排气Runner V ents 抛光Draw Polish 侧抽芯 Side Action 加强筋 Reinforcing 三角撑 Gusset 柱子Bossed 出模斜度Draft 外廊Contour 落单会议Kick-Off Meeting 装卸孔 Handling Hole 运输安全带 Moldstrap 码模槽 Clamp Slot 撑头Support Pillar 螺牙1/2-13 Eye Bolt 1/2-13Tap 导柱位 Leader Pin Location 耐落胶 Teflon Paste 偏移量 Offset 水塞Water Line Plug

模具用语中英文对照

模具用语中英文对照 198各式模具分类用语中英文对照 landed plunger mold 有肩柱塞式模具 burnishing die 挤光模Www_17He_com landed positive mold 有肩全压式模具 button die 镶入式圆形凹模一起呵_英语站loading shoe mold 料套式模具center-gated mold 中心浇口式模具一起呵@英语站loose detail mold 活零件模具 chill mold 冷硬用铸模 loose mold 活动式模具 clod hobbing 冷挤压制模一起呵@英语站louvering die 百叶窗冲切模 composite dies 复合模具英.语.站 manifold die 分歧管模具一起呵_英语站counter punch 反凸模英语.站 modular mold 组合式模具 double stack mold 双层模具17He~Com multi-cavity mold 多模穴模具 electroformed mold 电铸成形模 multi-gate mold 复式浇口模具 expander die 扩径模一起呵.英语.站offswt bending die 双折冷弯模具

extrusion die 挤出模英语.站 palletizing die 叠层模一起呵@英语@站family mold 反套制品模具一.起.呵.英语站plaster mold 石膏模 17he_com blank through dies 漏件式落料模一porous mold 通气性模具duplicated cavity plate 复板模一起呵@英语站positive mold 全压式模具 fantail die 扇尾形模具 17he_com pressure die 压ingot mold 钢锭模 punching die 落料模 lancing die 切口模英语.站 raising(embossing) 压花起伏成形 re-entrant mold 倒角式模具 sectional die 拼合模 runless injection mold 无流道冷料模具一起呵_英语站 sectional die 对合模具英.语.站 segment mold 组合模一起_呵_英语站 semi-positive mold 半全压式模具一起_呵_英语站 shaper 定型模套 single cavity mold 单腔模具

模具常用术语中英文对照

模具常用术语中英文对照模具常用术语中英文对照中文英文模芯Parting Core 局部视图Partial View 冷料# ColdSllig 线切割Wire E.D.M 轮廊Contour 螺纹孔Tapping Hole 连接件Fittings 斜针AnglePin 接合Engage 替换镶件Interchangeable Mold Inserts 指定吨位的注塑机SpecificPress 水嘴接头Water Fittings 螺纹Eyebolt Thread 回针Stop Pin 二级顶出针Sub-LeaderdPin 镶件Mold Insert 加硬Hapden 唧嘴Sprue 设计筒图DesignPreliminary 名称块表 Title Block 版本标识Revision Level 材料清单Stock List 制模Build Mold 手动滑块Hand Slide 漏水测试LeakTest 流道排气Runner Vents 抛光Draw Polish 侧抽芯SideAction 中文英文加强筋Reinforcing 三角撑Gusset 柱子Bosse 出模斜度Draft 外廊Contour 落单会议Kick-Off Meeting 装卸孔Handl Ing Hole 运输安全带Moldstrap 码

模槽ClampSlot

撑头Support Pillar 螺牙1/2-13 EyeBolt 1/2-13Tap 导柱位LeaderPin Location 耐落胶Teflon Paste 偏移量Offset 水塞 Water Line Plig 撬模脚PpySlot 重新加工Reworked 配件Components 补偿 Compensation 平面度 Parallel 倒角 Chamfer 模胚 Mold Base 热嘴 Hotnozzle 火花机 Edm 熔接线 Weildline 压机 Press 晒纹 Texturing 梯形Trapezoio 凸缘、法兰Flange 模具常用术语中英文对照中文英文方铁 SpacerBlock 顶针板 Ejector Plate

模具设计与制造中英文外文翻译文献

中英文对照资料外文翻译文献模具设计与制造模具是制造业的重要工艺基础，在我国，模具制造属于专用设备制造业。中国虽然很早就开始制造模具和使用模具，但长期未形成产业。直到20世纪80 年代后期，中国模具工业才驶入发展的快车道。近年，不仅国有模具企业有了很大发展，三资企业、乡镇（个体）模具企业的发展也相当迅速。虽然中国模具工业发展迅速，但与需求相比，显然供不应求，其主要缺口集中于精密、大型、复杂、长寿命模具领域。由于在模具精度、寿命、制造周期及生产能力等方面，中国与国际平均水平和发达国家仍有较大差距，因此，每年需要大量进口模具。中国模具产业除了要继续提高生产能力，今后更要着重于行业内部结构的调整和技术发展水平的提高。结构调整方面，主要是企业结构向专业化调整，产品结构向着中高档模具发展，向进出口结构的改进，中高档汽车覆盖件模具成形分析及结构改进、多功能复合模具和复合加工及激光技术在模具设计制造上的应用、高速切削、超精加工及抛光技术、信息化方向发展。近年，模具行业结构调整和体制改革步伐加大，主要表现在，大型、精密、复杂、长寿命、中高档模具及模具标准件发展速度高于一般模具产品；塑料模和压铸模比例增大；专业模具厂数量及其生产能力增加；“三资”及私营企业发展迅速；股份制改造步伐加快等。从地区分布来看，以珠江三角洲和长江三角洲为中心的东南沿海地区发展快于中西部地区，南方的发展快于北方。目前发展最快、

模具生产最为集中的省份是广东和浙江，江苏、上海、安徽和山东等地近几年也有较大发展。虽然我国模具总量目前已达到相当规模，模具水平也有很大提高，但设计制造水平总体上落后于德、美、日、法、意等工业发达国家许多。当前存在的问题和差距主要表现在以下几方面：（1）总量供不应求国内模具自配率只有70%左右。其中低档模具供过于求，中高档模具自配率只有50%左右。（2）企业组织结构、产品结构、技术结构和进出口结构均不合理我国模具生产厂中多数是自产自配的工模具车间（分厂），自产自配比例高达60%左右，而国外模具超过70%属商品模具。专业模具厂大多是“大而全”、“小而全”的组织形式，而国外大多是“小而专”、“小而精”。国内大型、精密、复杂、长寿命的模具占总量比例不足30%，而国外在50%以上。2004年，模具进出口之比为3.7:1，进出口相抵后的净进口额达13.2亿美元，为世界模具净进口量最大的国家。（3）模具产品水平大大低于国际水平，生产周期却高于国际水平产品水平低主要表现在模具的精度、型腔表面粗糙度、寿命及结构等方面。（4）开发能力较差，经济效益欠佳我国模具企业技术人员比例低，水平较低，且不重视产品开发，在市场中经常处于被动地位。我国每个模具职工平均年创造产值约合1万美元，国外模具工业发达国家大多是15～20万美元，有的高达25～30万美元，与之相对的是我国相当一部分模具企业还沿用过去作坊式管理，真正实现现代化企业管理的企业较少。造成上述差距的原因很多，除了历史上模具作为产品长期未得到应有的重视，以及多数国有企业机制不能适应市场经济之外，还有下列几个原因：（1）国家对模具工业的政策支持力度还不够虽然国家已经明确颁布了模具行业的产业政策，但配套政策少，执行力度弱。目前享受模具产品增值税的企业全国只有185家，大多数企业仍旧税负过重。模

模具DFM常用中英文对照

D F M常用中英文对照 15、如果分型面此处，模具上会有尖角和刀口，对模具寿命有影响。 There are sharp edges if we set the parting line here, it will reduce the tool life. 16、此处料厚段差很大，成品表面会有应力痕，建议修改如图示。 The thickness is not equal and it will bring the stress lines on the surface, suggest to improve the part as the picture shown. 17、此大行位上有小行位，开模时小行位需先退，大行位做延时，合模时则相反。 The small slider is inside the big slider, when the mold open, the small slider need to recede first and the big slider have to postpone. When the mold close, it is contrary. 18、此处需做强顶。 This position need to force ejection. 19、由于此处没有足够空间下热咀，所以需做一个柱子进胶。 This position need to make a pole for gating because there have no enough space for hot sprue. 20、沾模， Stick 1.High shrinkage values could indicate sink marks or voids at gate location 高缩水率的产品容易产生缩印，但在浇口附近可以避免。 2.Welding line on the cosmetic surface 熔接线在外表面 3.Two banana gate was to being confluent in the end of melt flow. 两个香蕉浇口在流动未端熔合。 4.Venting insert here has flash 排气镶件处有飞边