BT137M中文资料

GENERAL DESCRIPTION

QUICK REFERENCE DATA

Glass passivated triacs in a plastic SYMBOL

PARAMETER

MAX.MAX.MAX.UNIT envelope,suitable for surface mounting,intended for use in BT137S (or BT137M)-500600800applications requiring high BT137S (or BT137M)-500F 600F 800F bidirectional transient and blocking BT137S (or BT137M)-500G 600G 800G voltage capability and high thermal V DRM Repetitive peak off-state 500600800V cycling performance.Typical voltages

applications include motor control,I T(RMS)RMS on-state current

888A industrial and domestic lighting,I TSM

Non-repetitive peak on-state 65

heating and static switching.

current

PINNING - SOT428

PIN CONFIGURATION

SYMBOL

LIMITING VALUES

Limiting values in accordance with the Absolute Maximum System (IEC 134).SYMBOL PARAMETER

CONDITIONS

MIN.MAX.UNIT -500-600-800V DRM Repetitive peak off-state -5001

6001800

V voltages

I T(RMS)RMS on-state current full sine wave; T mb ≤ 102 ?C

-8A I TSM

Non-repetitive peak full sine wave; T j = 25 ?C prior to on-state current surge t = 20 ms -65A t = 16.7 ms -71A I 2t I 2t for fusing

t = 10 ms

-21A 2s dI T /dt

Repetitive rate of rise of I TM = 12 A; I G = 0.2 A;on-state current after dI G /dt = 0.2 A/μs

triggering

T2+ G+-50A/μs T2+ G--50A/μs T2- G--50A/μs T2- G+-10A/μs I GM Peak gate current -2A V GM Peak gate voltage -5V P GM Peak gate power -5W P G(AV)Average gate power over any 20 ms period

-0.5W T stg Storage temperature -40150?C T j

Operating junction -125

temperature

1 Although not recommended, off-state voltages up to 800V may be applied without damage, but the triac may switch to the on-state. The rate of rise of current should not exceed 6 A/μs.

THERMAL RESISTANCES

SYMBOL PARAMETER

CONDITIONS

MIN.TYP.MAX.UNIT R th j-mb Thermal resistance full cycle -- 2.0K/W junction to mounting base half cycle -- 2.4K/W R th j-a

Thermal resistance pcb (FR4) mounted; footprint as in Fig.14-

K/W

junction to ambient

STATIC CHARACTERISTICS

T j = 25 ?C unless otherwise stated SYMBOL PARAMETER CONDITIONS

MIN.

TYP.

MAX.UNIT

BT137S-(or BT137M)...

...F ...G I GT

Gate trigger current

V D = 12 V; I T = 0.1 A

T2+ G+-5352550mA T2+ G--8352550mA T2- G--11352550mA T2- G+

-307070100mA I L

Latching current

V D = 12 V; I GT = 0.1 A

T2+ G+-7303045mA T2+ G--16454560mA T2- G--5303045mA T2- G+

-7454560mA I H Holding current V D = 12 V; I GT = 0.1 A -520

2040

mA V T On-state voltage I T = 10 A

- 1.3 1.65V V GT Gate trigger voltage V D = 12 V; I T = 0.1 A -0.7 1.5V V D = 400 V; I T = 0.1 A;0.250.4-V T j = 125 ?C I D

Off-state leakage current

V D = V DRM(max);-0.1

0.5

mA T j = 125 ?C

DYNAMIC CHARACTERISTICS

T j = 25 ?C unless otherwise stated SYMBOL PARAMETER CONDITIONS

MIN.TYP.MAX.UNIT BT137S-(or BT137M)......F ...G dV D /dt

Critical rate of rise of V DM = 67% V DRM(max);100

200

250

-V/μs

off-state voltage T j = 125 ?C; exponential waveform; gate open circuit

dV com /dt

Critical rate of change of V DM = 400 V; T j = 95 ?C;--1020-V/μs

commutating voltage I T(RMS) = 8 A;

dI com /dt = 3.6 A/ms; gate open circuit

t gt

Gate controlled turn-on I TM = 12 A; V D = V DRM(max);---2-μs

time

I G = 0.1 A; dI G /dt = 5 A/μs

MECHANICAL DATA

MOUNTING INSTRUCTIONS

Notes

1. Plastic meets UL94 V0 at 1/8".

DEFINITIONS

Data sheet status

Objective specification This data sheet contains target or goal specifications for product development. Preliminary specification This data sheet contains preliminary data; supplementary data may be published later. Product specification This data sheet contains final product specifications.

Limiting values

Limiting values are given in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of this specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information

Where application information is given, it is advisory and does not form part of the specification.

? Philips Electronics N.V. 1997

All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner.

The information presented in this document does not form part of any quotation or contract, it is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent or other industrial or intellectual property rights.

LIFE SUPPORT APPLICATIONS

These products are not designed for use in life support appliances, devices or systems where malfunction of these products can be reasonably expected to result in personal injury. Philips customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such improper use or sale.