石油钻井专业词汇
drill spool 1.accumulator 储能器 2.active tank 循环池 3.adjusting bolt (刹把)调节螺栓4.admission pipe 进气管 5.agitator 搅拌器 6.air chamber 空气包7.air line 气管线8.air-operated hoist 气动绞车9.alternating current drive 交流电驱动10.annular BOP 环形BOP 11.ato-muffler 消音器12.ball valve 球阀13.bell nipple 老虎钳14.bench vise 钻头15.bit 钻头16.Bit gauge 钻头装卸器17.bit gauge 钻头规18. blind ram preventer 盲板防喷器19. blind shear ram preventer 剪切闸板防喷器20.blow-out preventer（BOP）防喷器21.bolt 螺栓22.BOP control panel 防喷器控制盘23.BOP deck 防喷器平台24.bottom plug 底塞25.box 母扣26.brake level(brake handle) 刹把27.brake line(brake staple) 刹带28.bridge plug 桥塞29.buttress 梯形扣30.butterfly valve 蝶阀31.by-pass 旁通32.by-pass plug 旁通塞33.callipers 卡钳34.casing bowl 套管打捞筒35.casing coupling 套管接箍36.casing cutter 套管割刀37.casing elevator 套管吊卡38.casing hanger 套管悬挂器39.casing head 套管头40.casing monkey board 套管平台41..casing scraper 刮管器42.casing shoe 套管鞋43.casing slip 套管卡瓦44.casing spear 套管打捞矛45.casing spool 套管四通46.casing tong 套管大钳47.cat line 锚头绳48.cat line grip 锚头绳爪49.cat shaft 锚头轴50.cat-head 锚头51.cellar deck 井口甲板52.cement 水泥53.cement basket 水泥伞54.cement plug 水泥塞55.cement retainer 水泥阻流环56.cementing bond log 固井质量检查57.cementing head 水泥头58.cementing line 固井管线59.cementing pump 固井泵60.chain 链61.chain pipe tong 链钳62.chain tong 链钳63.chamber 房间,寝室64.chamber gate 阀箱,闸室65.charge pump 灌注泵66.check valve 止回阀,回压凡尔67.choke 节流器,阻流器68.choke line 阻流管线69.choke position indicator 节流阀位置指示器70.choke valve 节流阀71.choke -line manifold 阻流管汇72.clutch 离合器73.conductor 导管74.cone 牙轮75.cone fisher 牙轮打捞器76.cone lock 牙轮卡死77.cooling-water pump 冷却水泵78.core barrel shoe 取心筒鞋79.core basket 取心爪80.core bit 取心钻头81.core catcher 岩心爪82.∞re catcher case 岩心爪外套83.core drying oven 岩心烘箱84.crossover joint(x/o) 变换接头85.crown block 天车86.crown block beam 天车梁87.dead line 死绳88.dead line diaphragm 死绳固定器膜片89.dead line anchor 死绳固定器90.degasser 除气器91.derrick 井架92.desander(desilter) 除砂(泥)器93.direct current drive 直流电驱动94.discharge line 排出管线95.discharge valve 排出阀96.double ram type preventer 双闸板防喷器97.down hole tool 人井工具98.draw works 绞车99.drawworks motor 绞车电机100.drift mandrel 通径规101.drill collar 钻链102.drill collar slip 钻链卡瓦103.drill pipe 钻杆104.drill pipe slip 钻杆卡瓦105.drill pipe wiper 钻杆刮泥器106.ddll string 钻柱107.driller'sb console 司钻控制台108.drilier's monitor 司钻监视器109.drilling line(workline) 钻井大绳110.driiling stem valve 钻杆防喷器111.drive shaft 驱动轴112.driven shaft 从动轴113.driving chain 传动链条114.drum 滚筒115.drum capacity 滚筒容量116.drum clutch 滚筒离合器117.drum hight air clutch 滚筒高速（低速）118.drumlow air clutch 空气离合器119.DV collar 分级箍120.eddy current brake 涡磁刹车121.elevator 吊卡122. elevator link 吊卡耳环123.elevator-spider 吊卡-卡瓦124.emergency jaw clutch 应急牙嵌离合器125.equalizing yoke (刹带的)平衡杠126.external cutter 外卡钳127.external cutter 外部割刀128.eye plate 吊耳，吊环129.eye splice 绳套,接环130.fill up iine 灌泥浆管线131.fiitration test apparatus 失水测定仪132.finger board 指梁133.fishing hook 打捞钩134.fishing head 打捞头135.fishing jars 打捞振击器136.fishing neck 打捞颈137.fishing nipple 打捞公锥138.fishing operation 打捞操作(作业) 139.fishingmcitet 打捞母锥140.fishing spear 打捞矛141.fishing string 打捞管柱142.fishing tap(taper) 打捞公锥143.fishing tool 打捞工具144.flange 法兰145.flat(round,square)file 扁(圆,方)锉146.flat bit tongs 扁嘴钳(电工用)
147.flat bottom mill 平底锐鞋148.flexible joint 挠性接头149.float shoe 浮鞋150.float valve 浮阀151.floating collar 浮箍152.four →way valve 四通阀153.free point indicator 卡点测定仪154.full hole joint 贯眼钻杆接头155.funnel viscometer 漏斗粘度计156.gas holder(tank) 储气筒,储气罐157.gate 大门158.gate valve闸门阀159.g∞se neck pipe 鹅颈管160.hammer 锤子161.heavey weight drill pipe 加重钻杆162.heaηr wall drill pipe 厚壁钻杆163.high pressure line 高压管线164.hole opener 开眼器,扩眼器165.hook 大钩166.hook spring 大钩弹簧167.hose 水龙带168.hydraulic break-out cylinder 卸扣液缸169.hydraulic catwork 液压猫头170.hydraulic pump 液压泵171.hydraulic reservoir- 液压油箱172.hydraulic tong 液压大钳173.hydraulic valve 咒液动阀174.hydraulic (press) test pump 液动试压泵175.hydraulic-powered winch 液压绞车176.inertia 惯性177.inertia brake 惯性刹车178.inlet 人口179.inner core barrel 内岩心筒180.intermediate casing 中间(技术)套管181.internal blowout preventer 钻柱内防喷器182.internal callipers 内卡钳183.internal external upset 内外加厚184.internal flush joint 内平钻杆接头185.jar 振击器186.jaw clutch 牙嵌离合器187.joint 接头,(钻杆)单根188.junk basket 笼式打捞篮189.junk catcher 打捞爪,一把抓190.junk sub 打捞杯191.kelly bushing 方补心192.kelly cock 方钻杆考克193.kelly protective sub 方保接头194.kdly spinner 方钻杆旋转短节195.key seat reamer 键槽破坏器196.killline 压井管线197.knee pipe 弯管https://www.360docs.net/doc/567885342.html,dder 梯子199.level 水平仪(尺) 200.lifting plug 提升丝堵201.lifting sub 提升短节202.line reeving 滑车装绳数203.liner 缸套204.liner 尾管205.lock bolt 锁紧螺栓206.locking flange 锁紧法兰207.low pressure line 低压管线208.lube oil pump 润滑油泵209.lubrication hole 加油孔210.magnetic fishing tool 磁力打捞工具211.make out cathead 卸扣猫头212.make up cathead 上扣猫头213.manual drill 手摇钻214.manual valve 手动阀215.master bushing 转盘大补心https://www.360docs.net/doc/567885342.html,ling shoe 镜鞋https://www.360docs.net/doc/567885342.html,ling tool 锐具218.mixing hopper 混合漏斗219.mixing pump 混合泵220.monkey hard 猴台221.motor 电机,马达222.mouse hole 小鼠洞223.mud balance 泥浆比重计224.mud cleaner 泥浆清洁器225.mud ditch 泥浆槽226.mud guard 挡泥板227.mud gun 泥浆枪228.mud pump 泥浆泵229.mud relief valve 泥浆泵安全阀230.mud return line 泥浆返出管线231.mut pit 泥浆池232.nail 钉子233.near-bit stabilizer 近钻头扶正器234.needle valve 针形阀235.nigger-head 扳手加长套筒236.nipper 慑子,夹子237.non-magnetic drilling collar 非磁钻键238.normal close valve 常闭阀239.normal open valve 常开阀240.nozzle 水眼,喷嘴241.nut 螺帽242.nut bolt 带帽螺栓243.nut spinner 自动螺母扳手244.oil level 油位245.oil level check plug 油位检查丝堵246.oil tank 油柜247.oil-level dipstick 油尺248.open -ended spanner 开口扳手249.outer core barrel 外岩心筒250.outlet 出口251.paint brush 油漆刷252.pilot bit 领眼钻头253.pin 公扣254.pin 销子255.pincers 钳子,夹子256.pinch bar 撬棍257.piston 活塞258.piston cup 活塞皮碗259.piston rod 活塞杆260.pliers 手钳子261.plug valve 旋塞阀262.pneumatic t∞l 气动工具263.Portland cement 硅酸盐水泥264.power slip 动力卡瓦265.power supply unit 动力供应设备266.power tong 动力大钳267.power wrench 动力扳手268.pressure snubbing tank 缓冲罐269.production casing 生产层套管270.pulley 滑轮271.pump-out reversing sub 反循环接头272.pup pipe joint 短钻杆273.quick connection 快速联结274.ramp (井架大门处)坡板275.rat hole 大鼠洞276.regular tool joint 正规钻杆接头277.regulator valve 调节阀278.relief line 放压管线279.retaining ring (support ring) 承托环280.reverse circulating valve 反循环阀281.reverse circulation junk basket 反循环打捞篮282.reverse circulation port 反循环孔283.reverse gear 倒档齿轮284.reversing tool 倒扣(打捞)工具285.ring gasket 钢圈286.ring spanner 梅花扳手287.rivet 佛钉288.rotary table 转盘289.rotary table motor 转盘
电机290.rotary table motor blower 转盘风机291.safety clamp(slips) 安全卡瓦292.safety joint 安全接头293.safety stop 安全限位挡块294.safety switch 安全开关295.safety-strap(belt) 安全带296.sand reel 捞砂滚筒297.screen cloth 筛布298.screw 螺钉299.screw driver 螺丝刀300.seamless pipe 无缝钢管301.setback 立根盒302.setback capacity 立根盒容量303.settling pit 沉砂池304.shaft 轴305.shale shaker 振动筛306.shock absorber 减震器307.side doo elevator 倒开门吊卡308.single joint elevator 单根吊卡309.single ram type preventer 单闸板防喷器310.slide rule 计算尺311.slide tongs 管钳312.sling 吊索313.slip 卡瓦314.slip bushing 卡瓦补心315.slip bushing 卡瓦补心316.slip dog 卡瓦牙板317.slip groove 卡瓦槽318.slip insert 卡瓦牙319.slip insert 卡瓦打捞筒320.slipgxket bowl (卡瓦)锥形座321.socket 套筒扳手322.spider 卡盘323.spiral drill collar 螺旋钻链324.spud spear 钢丝绳打捞钩325.spudding bit 开眼钻头326.stab -in cementing 插入式注水泥327.subbing hard 对扣台(下套管用) 328.stabilizer 扶正器329.stainless steel 不锈钢330.stand pipe 立管331.stinger 插入头332.stinger strings (内管)注水泥管柱333.stud 双端螺栓334.stud bolt 双头螺栓335.stuffing box 盘根盒336.sub 接头337.suction line 吸入管线338.suction valve 吸人阀339.surface casing 表层套管340.swivel 水龙头341.tape measure 卷尺342.tee 三通343.thrmd 丝扣344.thread dope 丝扣油345.thread protector 护丝346.three-cone bit 三压轮钻头347.tong 大钳348.tong bucket 大钳平衡器349.tong dies 大钳牙板350.tong head 钳头351.tong mark 大钳刻痕352.tong space 大钳搭绞部位353.tool joint 工具接头354.tool steel 工具钢355.top(bottom)plug 顶(底)塞356.top of the cement 水泥面357.TOTCO ring baffle plate TOTCO承托环358.traveling block 游动滑车359.tdp-tank 泥浆计量罐360.two way valve 两通阀361.v-door 井架大门362.valve 阀门363.valve 阀,凡尔364.valve body 凡尔体365.valve bonnet 阀盖,阀帽366.valve cup(seat) 凡尔座367.valve face 阀面368.valve lever 阀杆369.valve seal 阀密封370.valve seat grab 起阅座器371.valve spring 阀弹簧372.vernier 灵敏指针373.vice(=vise) 虎钳374.wall hook 壁钩375.wash pipe 冲管376.wear bushing 耐磨补心377.well-head equipment 井口装置378.whip stock 造斜器,斜向器379.wing stabilizer 翼状扶正器（二）．钻井作业有关词语1.type "L" connector 20"L" 型接头 2.ahead water 先行水3.annular velocity 环空流速4.apparent viscosity 表观粘度5.back off 倒扣,卸扣 6.back pressure 回压7.back up attachment 打好背钳8.ball up 泥包9.ballast water 压舱水10.behind water 尾水11.bingham model 宾汉模型12.bit cost 钻头成本13.bit diameter 钻头直径14.bit footage 钻头进尺15.bit IADC code 钻头IADC编码16.bit lift 钻头寿命17.bit position 钻头位置18.bit series number 钻头系列号19.bit teeth 钻头齿20.bit time 钻头时间21.bit type 钻头类型22.bit wear 钻头磨损23.blow job 吹扫作业24.blow line 扫线用管线25.blowing pressure 吹压压力26.blowout 井喷27.blowout control 防喷28.blowout control equipment 防喷设备29.BOP handling 装卸防喷器30.bottom fill 沉砂31.bottom-hole pressure 井底压力32.box-box∞nnedior1 双母接头33.casing program 套管程序34.casing size 套管尺寸35.cationic surface active agent 阳离子表面活性剂36.caustic soda 烧碱37.cement bond 水泥胶结38.cement channeling 水泥窜槽39.cement failure 固井失败40.cement flush 水泥冲洗41.cement slurry 水泥浆42.cementing formulation 固井配方43.circulation 循环44.clay base mud 粘土泥浆45.control drilling 控制钻进46.coring sample 岩心取样47.corrosion 腐蚀48.critical velocity 临界速度49.crown block protector 天车防碰装置50.crown block saver 天车防碰装置51.cut off drilling line 割大绳52.danderous objects 危险品53. degasser efficiency 除气器效率54.detergent 除垢剂,清洁剂55.deviation survey 井斜测量56.differential pressure sticking 压差卡钻57.directional drilling
定向钻井58.directional well 定向井59.dog leg 狗腿60.dog leg ratio 狗腿率61.down time 停工时间62.drifting 通径63.drilling assembly 钻具组合64.drilling break 钻进突变65.drilling contractor 钻井承包商66.drilling cost 钻井成本67.drilling hours 钻进时间68.drilling operation 钻井作业69.drilling program 钻井程序70.drilling report 钻井报表71.drilling daily report 钻井日报72.drilling water 钻井水73.dull bit grading 钝钻头分级74.dyna-drill 戴纳钻具75.emulsifying agent 乳化剂76.erode out 刺坏77.evaluation well 评估井78.exploratory well 初探井79.fatigue limit 疲劳极限80.fill-up float shoe 自动灌浆浮鞋81.filter cake 泥饼82.filtration-reducing agent 降失水剂83.flocculation 絮凝作用84.flowing pressure 流压85.fluid loss 失水86.formation 地层87.formation test 地层测试88.formation water 地层水89.fresh water 淡水,清水90.function test 功能试验91.gas content 气含量92.gas cut 气侵93.gas in mud 泥浆中的气94.gas reservoir 气层95.gas showing 气显示96.hard formation 硬地层97.hole sin 井眼尺寸98.hole straightening 井眼纠斜99.hook load 大钩负荷100.hook position 大钩位置101.initial gel-strength 初切力102.inner string cementing 内管注水泥103.interface level indicator 表面活性剂104.kelly down 方人105.kelly down depth 方人深度106.kelly in 方人107.kelly up 方余108.key-gating sticking 键槽卡钻109.kick 井涌110.kick control 控制井涌111.killwell 压井https://www.360docs.net/doc/567885342.html,y down the drill pipe 甩钻杆113.leak –off test 漏失试验114.left-hand J-slot 左旋"J"型槽115.log time 迟到时间116.low solid mud 低固相泥浆117.maximum pressure 最小速度118.maximum speed 最大速度119.mean sea level 平均海平面120.meantide level 平均潮面121.mud additive 泥浆添加剂122.mud column 泥浆柱123.mud conditioning 调节泥浆124.mud conditioning materials 泥浆处理材料125.mud line 泥线126.mud logging 泥浆录井127.mud volume 泥浆量128.no leak 不漏129.no return 无返出130.nozzle efficiency 水眼效率131.nozzle size 水眼尺寸132.off –bottom 离开井底133.offshore 海上134.oil leak 漏油135.oil reservoir pressure 油层压力136.oil resistant gom 耐油橡胶137.oil seal 油封138.oil shale 油页岩139.oil-base mud 油基泥浆140.on bottom 接触井底141.open hole 裸眼142.operator 作业者143.overpull 上提,遇卡144.overtonging 上扣过紧145.pendulum bottom hole assembly 钟摆钻具组合146.penetration rate 机械钻速147.plastic viscosity 塑性粘度(PV) 148.plastics 塑料149.plugging back 水泥回堵150.pressure loss in pipe 管内压降151.pressure test 压力试验152.pump down plug 泵入水泥塞153.pump efficiency 泵效154.pump pressure 泵压155.pump speed 泵速156.pump stroke 泵冲157.rated now 额定流量158.reaming 划眼159.record 记录160.recording paper 记录纸161.releasing spear 松开捞矛162.retarder 缓凝剂163.reverse circulation 反循环164.rig floor 钻台165.rotary speed 转盘转速166.run casing 下套管167.running time 运转时间168.running tool 下人工具169.sand bridge 砂桥170.saturatedmlt-water mud 饱和盐水泥浆171.sea sick 晕船172.seawater mud 海水泥浆173.setting slip 坐卡瓦174.shallow gas 浅层气175.shaly sand 泥质砂岩176.short trip 短起下177.shut -in 关井178.shut-in casing pressure 关井套压179.shut-incasing pipe pressure 关井钻杆压力180.sick leave 请病假181.side tracking 侧钻182.slip drilling line 倒大绳183.sloughing,caving (井壁)拥塌184.soda 苏打185.soft formation 软地层186.solid content 固相含量187.spud in 开钻188.spud mud 开钻泥浆189.squeeze cement 挤水泥190.stage cementing 分级注水泥191.stand-by 待命,待机192.stant-by rate 待命费193.start up(pump) 启动(泵) 194.static pressure
石油工程专业英语单词总结
3-D seismic survey (D: dimension:) 三维地震勘探 5-spot pattern n.五点井网Abandon v.（油井）报废，废弃Abandon well n.废井Acid wash n.酸洗 Acidization n.酸化（作用）Acidization n.酸化（作用） Acidize v.酸化Additive n.添加剂 Agent n.试剂，媒介Alkane n.烷烃，链烷烃 Analytic solution n.解析解Anisotropic a.各向异性的，非均质的Annular a.环形的Annular mist flow n.环雾流 Annulus n.环形空间，环空Anticline n.背斜 API standards n.美国石油协会标准Aromatic n.芳香族，芳香族环烃；a. 芳香的 Artifical lift n.人工举升Artificial lift n.人工举升 Artificial water drive n.人工注水驱Asphaltene n.沥青烯 Asphaltic a.含沥青的，沥青质的；n.沥青质Associated a.伴生的 Attribute n.属性，特征，标志Baffle n.隔板；v.阻碍，挫折Barefoot completion n.裸眼完井Barite n.重晶石 Barrel n.桶Barrier n.隔层 Bbl (blue barrel) Bean n.油嘴，节流器 Belt cover n.皮带盖Bentonite n.膨润土，斑脱岩 Bit n.钻头Black-oil simulator n.黑油模拟器Blender truck n.混砂车Blow out v.井喷 Blowout n.井喷Blowout preventer (BOP) n.防喷器Borehole n.井眼Bottom hole n.井下 Collapse v.坍塌，倒塌Collar n.钻铤 Compaction n.压实作用Compaction n.压实（作用），挤压Completion n.完井，完成，结束Compress v.压缩 Compressor n.压缩机Concentration n.浓度；集中Condensate n.凝析油Condensate n.凝析油 Conductor casing n.导管Conductor casing n.导管 Conductor hole n.导管孔Conductor pipe n.导管 Cone n.圆锥，（锥形）牙轮Configuration n.构造 Connate a.原生的，共生的Connate water n.原生水，共生水Contaminant n.杂质，污染物Continuous lift n.连续气举 Core n.岩心Core n.岩心 Core holder n.岩心夹持器Core slug n.岩心塞 Coring bit n.取芯钻头Corrode v.腐蚀 Corrode v.腐蚀，侵蚀；锈蚀Corrosion n.腐蚀 Corrosion n.腐蚀Corrosive a.腐蚀的；n.腐蚀剂Corrosive a.腐蚀的；n.腐蚀剂Counterbalance n.平衡（块）；v.使平衡，抵消 Counterweight n.平衡块Crack v.裂开 Crank n.曲柄，摇把Crown block n.钻台 Crumble v.坍塌，破碎Crust n.地壳 Curve n.曲线Cutting/chips n.钻屑
石油钻井英语词汇
对照实物确认的钻井词汇 一、井口与井控 1.套管头升高短节（上下由法兰连接，中间是三通或四通）casing spool 2.油管悬挂器tubing hanger 3.油管悬挂器上边接有阀门的盖子tubing bonnet 4.（可焊接的）导管头（接箍）conductor connector 5.（可焊接的）套管头（接箍）casing connector 6.井口帽blanking cap & plug 7.三闸板防喷器triple slide-lok preventer 8.双闸板防喷器double slide-lok prevente 9.油/套管升高短节tubing/casing riser 10.整体式升高短节integral union riser 11.法兰×丝扣井口转换头wellhead adapter 12.井口四通两边的横向阀门wing valves 13.油管悬挂器上边的变径法兰大小头bonnet 14.上边是法兰的套管头casing flange 15.只上边是法兰，下边与表层套管焊接的套管头casing head 16.套管头内的卡瓦casing slips 17.（上法兰小，下法兰大）变径套管头casing spool crossover 18.与导管焊接的坐在圆井底的套管头landing head flange top 19.卡瓦密封套管悬挂器slips seal casing hanger
20.（上下是法兰，中间是四通的）油管升高短节tubing spool 21.柔性封隔闸板flexpacker ram 22.可变径闸板variable bore ram 23.剪切闸板shearing blind ram 24.卡瓦型套管悬挂器slip-type casing hangers 25.高负荷悬挂器high-load hanger 26.悬挂器断开式密封圈hanger isolation seal ring 27.井口封隔变径变压法兰（中间有几道密封圈，下边是低压，上边是高压）packoff/crossover flange 28.油管头（下法兰大，内带密封圈；中间是四通，上法兰小）tubing heads 29.底（下）变径法兰（下边内径大，上边内径小）basic adapter 30.单密封变径法兰（下内径大，上内径小）single seal bore adapter 31.变径大小头（下边是法兰，上边是本体上钻孔攻丝扣）coupling adapter 32.油管悬挂器转换大小头短节（上法兰小，下法兰大，下法兰内有丝扣）tubingsuspension adapter 33.双油管悬挂器dual completion tubing hanger 34.双密封孔连接法兰dual seal bore adapter 35.锁紧螺丝lockdown screw 36.（地面）单油管密封总成single packer completion 37.法兰式采油树盖子flanged tree caps 38.扰性油管悬挂器coiled tubing hanger
钻井英语常用词汇及术语缩写.
API(America Petroleum Institute美国石油学会BHA(bottom hole assembelly井底钻具组合BHP(bottom hole pressure井底压力BOP control room远程控制台 BOP(blowout preventer防喷器 BTC(buttress thread connection梯形扣 CP(circulating pressure循环压力 DC(drill collar钻铤 DL(dogleg 狗腿 DLS(dogleg severity狗腿严重度DP(drill pipe钻杆 DST(drill stem test中途测试ECD(equivalent circulating density循环当量密度ECD(equivalent circulating density当量循环密度EF(external flush外平 EMW(equivalent mud weight当量泥浆密度EUE(external upset end内加厚 FCP(final circulating pressure终了循环压力FH(full hole贯眼扣 GPM(gallon per minute加仑每分HCR(hydraulic control remote valve液动阀 HP(hydrostatic pressure静液柱压力HWDP(heavy weight drillpipe加重钻杆 IADC(international association of drilling contractors钻井承包商 ID(inside diameter内径 IF(internal flush内平扣 KOP(kickoff point造斜点 LOT(leak off test漏失实验 LTC(long thread connection长园扣
(完整版)石油钻井工程英语词汇
地址：北京市朝阳区东三环中路7号财富中心A 座601 邮编：100020 石 油 钻 井 工 程 英 语 词 汇 2008-10-15 第一章：石油钻井工程英语基础词汇 第1 节 石油钻井工程基础词汇 钻井：drill 定向斜井：directional drilling 欠平衡钻井：under-balance drilling 海上钻井：off-shore drilling 陆地钻井： on-shore drilling 钻头：drill bit 刮刀钻头：drag bit 牙轮钻头：rock bit (镶齿钻头insert bit, 钢齿钻头steel toothed bit) 金刚石钻头：diamond bit 取心钻头：coring bit 钻头浮阀：float valve 钻头水眼：bit nozzle(or jet) 钻头水眼刺:bit nozzle washed out 钻头规：bit caliper(bit gauge) 钻头泥包：bit is balling 钻头钝了，我建议现在起钻：bit is dull. I suggest to POOH now
钻铤：DC(drill collar ) 光钻铤slick drill collar， 螺旋钻铤spiral drill collar 钻杆：DP(drill pipe ) 方钻杆：kelly 公扣：pin end 母扣：box end 内平式连接：IF(internal flash) 正规式连接：REG(regular) 贯眼式连接：FH(full hole)加重钻杆heavy weight drill pipe 短钻杆pop joint 井下马达：downhole motor 涡轮钻具：turbine 震击器：drilling jar 减震器：absorber 下部钻具组合：BHA（bottom hole assembly） 钻具扶正器：stabilizer（string stabilizer, near-bit stabilizer） 钻机：drill rig 钻井泥浆：drilling mud 钻井液：drilling fluid 钻井设备：drilling equipment油：oil 原油：crude oil 天然气：nature gas 煤层气：coal-bed gas 石油：petroleum 中国石油（简称）：CNPC（China National Petroleum Corporation ）长城钻井（简称）：GWDC(Great Wall Drilling Company) 采油：oil production 产油层(目的层)：reservoir( or pay zone) 钻进：drilling 调整钻井参数以得到理想的机械钻速： play the drilling parameters to get fast ROP 起钻：POOH(pull out of hole) 下钻：RIH(run in hole) 下套管：run casing(or RIH with casing) 短起下钻：wiper trip 循环泥浆：circulate 泥浆：reverse circulate 中途循环泥浆：break circulation 分段下钻：RIH in stages 通井：control trip 划眼：reaming 倒划眼：back reaming
井控常用英语词汇
Chapter 1 The Frequently Used-vocabulary In Well Control 井控常用词汇 1.abnormal pressure 异常压力(normal pressure, 正常压力 higher-than-expected/normal pressure, lower-than-normal pressure abnormally high pressure abnormally low pressure 2.accumulator储能器 3.accumulator bottle储能器瓶 4.acid fracture酸裂 5.adjustable choke可调节流阀 6.annular blowout preventer (BOP)环型 防喷器(ram BOP) bag BOP 7.annular pressure/casing pressure环空压 力(套压)(drillpipe pressure立压) pit gain 8.annular space环空(annulus) 9.annular velocity环空上返速度 10.anticline 背斜 11.atmospheric pressure 大气压 (0.1Mpa)(1at)
12.background gas 背景气 13.back off 倒扣/卸扣 make up 14.back-pressure 回压 check/单向阀 non-return valve回压凡尔 15.barite BaSO4重晶石 16.barium sulfate BaSO4 17.barrel (bbl) gallon/加仑 1m3=6.2897bbl 18.bell nipple 钟型导向短节,(喇叭口) 19.BHP (bottom hole pressure) 20.bleed 放喷 21.bleed line放喷管线 22.blind ram 全封闸板 pipe ram 半封闸板 shear ram 剪切闸板 23.blind ram preventer全封闸板防喷器 24.blowout 井喷 (kick 井涌) 25.blowout preventer control panel防喷器 控制面板 console 26.blowout preventer control unit防喷器控 制系统 27.blowout sticking 井喷卡钻
钻井现场常用英语专业词汇
Accumulator 储能器 Active tank 循环池 Adjusting bolt （刹把）调节螺栓Admission pipe 进气管 Agitator 搅拌器 Air chamber 空气包 Air line 气管线 Air-operated hoist 气动绞车Alternating current drive 交流电驱动Annular BOP 环形BOP Ato-muffler 消音器 Ball valve 球阀 Bell nipple 井口喇叭管 Bench vise 老虎钳 bit breaker 钻头装卸器 bit gauge 钻头规 blind ram preventer 盲板防喷器BOP control panel 防喷器控制盘BOP deck 防喷器平台 Bottom plug 底塞 Brake lever (brake handle) 刹把Brake line (brake staple) 刹带Bridge plug 桥塞 Buttress 梯形扣 Butterfly valve 蝶阀 By-pass 旁通 By-pass plug 旁通塞 Calipers 卡钳 Casing coupling 套管接箍 Casing cutter 套管割刀 Casing elevator 套管吊卡 Casing hanger 套管悬挂器 Casing head 套管头 Casing monkey board 套管平台Casing scraper 刮管器 Casing shoe 套管鞋 Casing slip 套管卡瓦 Casing spear 套管打捞矛 Casing spool 套管四通 Casing tong 套管大钳 Cat line 猫头绳 Cat line grip 猫头绳爪 Cat shaft 猫头轴 Cat-head 猫头 Cellar deck 井口甲板Cement 水泥 Cement basket 水泥伞 Cement plug 水泥塞 Cement retainer 水泥阻流环 Cementing bond log 固井质量检查Cementing head 水泥头 Cementing line 固井管线 Cementing pump 固井泵 Chain 链 Chain pipe tong 链钳 Chain tong 链钳 Chamber 房间，寝室 Chamber gate 阀箱，闸室 Charge pump 灌注泵 Check valve 止回阀，回压凡尔 Choke 节流器，阻流器 Choke line 阻流管线 Choke position indicator 节流阀位置指示器Choke valve 节流阀 Choke-line manifold 阻流管汇 Clutch 离合器 Conductor 导管 Cone 牙轮 Cone fisher 牙轮打捞器 Cone lock 牙轮卡死 Cooling-water pump 冷却水泵 Core barrel shoe 取心筒鞋 Core basket 取心爪 Core bit 取心钻头 Core catcher 取心爪 Core catch case 取心爪外套 Core drying oven 岩心烘箱 Crossover joint(x/o) 变换接头 Crown block 天车 Crown block beam 天车梁 Dead line 死绳 Dead line diaphragm 死绳固定器膜片Dead line anchor 死绳固定器 Degasser 除气器 Derrick 井架 Desander (desilter) 除砂器（除泥器）Direct current drive 直流电驱动Discharge line 排除管线 Double ram type preventer 双闸板防喷器Down hole tool 入井工具
钻井英文词汇表
顶驱&钻井英文常用词汇表 （第一版） 盘锦辽河油田天意石油装备有限公司 2010年9月
一、顶驱英文 顶部驱动系统Top drive system 车载钻机truck-mounted rig 机械的mechanical 电学的electrical 液压的hydraulic 钻井设备drilling equipment 大斜度井high-inclination well 深井deep well 丛式定向钻井cluster directional well 低温顶驱low-temperature top drive system 超深井ultra-deep well 定向井directional well 载荷load capacity 工作高度working height 电动机motor 功率power 转速rotary speed 钻井扭矩drilling torque 过载能力over load capacity 卸扣break out 上扣make-up 循环压力circulation pressure 额定压力rated pressure 电源电压power voltage 电源频率power frequency 工作电流working current 通风机ventilator 接线箱junction box 平衡油缸counterbalance cylinder 盘式刹车disc brake 电缆接插件cable connector assembly 主电机main motor 液压阀组hydraulic valve block 提环bail 鹅颈管gooseneck 油箱tank 蓄能器accumulator 齿轮箱gearbox 冲管总成wash pipe assembly 液压马达hydraulic motor 回转头rotating head 导轨guide beam 倾斜油缸tilt cylinder 防松法兰lock flange 背钳back-up tong 导向器stabbing guide 遥控IBOP upper IBOP 手动IBOP lower IBOP 吊环link 吊卡elevator 齿轮轴gear shaft 冷却风机Cooling motor 交流电机 AC motor 水龙头 Swivel 主齿轮 Driving gear 编码器 Encoder 散热器 Radiator 油道 Oil passage 密封槽Seal groove 轴承 bearing 滚轮 Roller 滑套 IBOP actuator shell 曲柄 Crank 销pin 钳牙tongdies 活塞piston 螺栓bolt 黄油grease 小车总成 Carriage accessory 气流 Air current 风道 Air duct 进风口 Air inlet 出风口 Air outlet 梨型环 Pear link 卡箍clamping band 键key
石油钻井单词翻译
Useful words of drilling常用钻井词汇 Senior mud engineer Driller toolpusHer roughnecks derrickman floorman 高级泥浆工程师司钻、队长、钻工、井架工场地工 Spud in Drill a well Stop Drilling Had Drilled/About 300Msdeep Be Drilling Drilling out of.. Finish drill ..In charge of.. 开钻打一口井停钻已经钻了约300米正在钻进钻完….完钻…负责人W..is? responsible to？…Ｗ..is ?responsible for？get every thing ready for..ing ？向谁负责？.. ？..负责什么？做…准备 ….ｗｈｏｍ.. ..ｗｈｏ.. 是.你们.的人是在.的人. nsbDRILLER'S Month, console log method station tour report monitor 钻机月、司钻（控制台、记录司钻法、平台钻井班报表监视器） DRILL extractor floor fluid footage free gauge hole hole returns hole survey in 钻井（打捞器钻台液进尺空转钻头规眼井口返浆测斜打开生产层）drill ability able liner able packer ahead assembly cable bit run expert collar collar annulus （可钻性可钻尾挂器可钻封隔器继续钻进钻柱组合钢丝行程专家钻挺钻挺环空）DRILL collar bore stem test string assemb limitation fatigue mechanics torque crew （钻挺水眼中测钻柱（结构强度疲劳力学扭矩井队）DRILL rig tool mill monitor off test out tool rope sample site solids stem bushing （钻机、钻具洗靴参数仪试钻钻塞工具棕绳砂样井场岩宵弯曲） DRILL PIPE annulus bore pin box clamp coupling cutter electric log elevator float frozen gauge inspection 钻杆（环空水眼公扣母扣卡瓦接箍割刀钻杆电测吊卡回凡尔卡钻丝扣规钻杆检查）DRILL PIPE protector release spinner stabilizer stand sticking sub tension winding up 钻杆（护丝钻具解卡旋扣器扶正器/稳定器立柱卡钻接头拉力弯曲） DRILLING engineer supervisor superntendent technique experience technology specialist technician （工程师监督总监技术经验工艺专家技术员）DRILLING analytical bit break capacity centralizer contract cost crew cycle data base effort engineering （分析钻头放空能力钻井扶正器合同成本队周期数据库工作量工程学）DRILLING equipment experience hanger load log mud operation optimization operator out outfit parameter （设备经验尾挂器钻压录井泥浆作业优化钻井承包商钻塞设备参数）DRILLING foreman hose implementer in balance instrument interval invasion zone jar journey line liner liner reel 钻井（队长/工头水龙带人员平衡钻进仪表井段漏层震击器记录表大绳尾管滚筒）DRILLING people permit phase prediction pressure program progress rate rate of trip record ship site speed （人员许可权阶段预报压力程序进度钻速行程钻速记录船井场钻速）DRILLING spool stem string stabilizer to completion tool substitute up weight turbine unit （四通钻柱钻柱扶正器钻至设计井深钻具接头钻碎钻压涡轮钻机组） DRILLING time log time work completion operation condition cleaning system bottoms up （钻时记录时间工作完井作业条件净化系统）迟到时间 pull of hole run in hole make up a joint break down a joint trip out of hole laying down wire line survey 起钻下钻接单根卸单根起钻甩钻具吊测 direction al well定向井词汇 DIRECTIONAL well angle bit bit side force component clinograph control counter depth migration 定向（定向井方位角钻头变方位侧向分力方位测斜仪方位控制计数器定向深度偏移）DIRECTIONAL diagram drilling drilling contractor drill tool Effect gyro hole line orientation tool presentation 定向(方位图定向钻井定向井承包商定向钻井工具效应陀螺仪井方向线定向工具方位显示) DIRECTIONAl reading scanning sub surveillance survey tendency tool turbodrill MWD survey tool 定向(方角读数定向扫描接头定向监测定向测量方向趋势随钻测斜仪定向涡轮随钻测量定向测量工具) direction sensor instrument of tilt of deflection of magnetization of strata parameter finding chart azimuth 方向（传感器方向仪倾斜方向井斜方位磁化方向地层走向方向参数测向系统）方向角deflecting tool angle build up angle drop off single shot inclinometer gyroscope whipstock horizontal well orbit 造斜工具增斜降斜单点测斜仪陀螺仪变向器）水平井轨迹Measure Depth Vertical Depth True Vertical Depth Displancement Closure Depth Vertica section Hole Inclination Hole Angle 井深/斜深垂深垂深水位/闭和距水位/闭和距视平移井斜角井斜角Declination Maximum Hole Angle Hole Direction Kick Off Point Dogleg Severity Target Tool face High Side Tool face Angle 慈偏角最大井斜角方位角造斜点全角变化率目标点工具面高边工具面角 sits the mark horizontal segment kick-off segment kick-off rate horizontal departure horizontal displacement 坐标水平段造斜段造斜率水平位移水平位移
钻井专业英语
一、钻井作业 1．钻台构造，设备，器材类： drilling equipment mast, derrick free standing mast drill floor v-door monkey board substructure mouse hole, rat hole gin pole setback crown block travelling block hook swivel power swivel draw works rotary table kelly kelly cock drum shaft cat head cat line deadline anchor sand line 钻井装置，钻机 井架 无绷绳轻便井架 钻台 坡板，井架大门 二层台 井架底座 鼠洞 人字架 立根盒 天车 游动滑车 大钩 水龙头 动力水龙头 绞车 转盘 方钻杆 方钻杆 滚动轴 猫头 猫头绳 死绳固定装置 捞绳器 work line ，drilling line deadline tong power tong kelly drive safety clamp elevator center latch elevator elevator chain block air hoist bushing master bushing inside BOP pipe wrench lifting sub kelly spinner geolograph cable jacket finger board slip rotary slip power slip 大绳 死绳 大钳 动力大钳 方钻杆滚子补心 安全卡子 吊卡 中开门吊卡 吊环 倒链 气动绞车 补心 转盘大补心 回压凡尔 管子扳手 提升短节 方钻杆旋转器 气测引绳 导管架 指梁 卡瓦 转盘卡瓦 动力卡瓦 2．钻头 3. Bit cone bit tri-cone bit bit noggle insert bit milled teeth bit diamond bit cone bit breaker hole openner 钻头 牙轮钻头 三牙轮钻头 钻头水眼 镶式钻头 铣齿钻头 金刚石钻头 牙轮 钻头装卸器 drilling assembly drill strings drill stem bit sub stabiliger wing stabiliger reamer drill pipe(drill collar) heavy weight drill pipe crossover sub 钻具组合 钻杆柱 钻柱 钻头接头 扶正器 翼状扶正器 辊轮扶正器 钻杆（钻铤） 加重钻杆
石油钻井词汇
石油钻井词汇 Part One SLICK-LINE（钢丝作业） A. TOOLS rope socket 绳帽 stem 加重杆 roll stem 滚轮加重杆 Tungsten stem 钨加重杆 Lead stem 铅加重杆 link jar 机械震击器 tubular jar 管状震击器 hydraulic jar 液压震击器 spring jar 弹簧震击器 knuckle joint 万向节 swivel joint 旋转节 wellhead adapter 井口变扣短节 X-Over 变扣 gauge cutter 通井规 selective downshift tool 选择性滑套开关工具 shiftting tool 移位工具 blind box 盲锤 L.I.B(lead impression block) 铅印swaging tool 胀管器 spear 打捞矛 prong grab 内捞矛 center spear 外捞矛 catcher 捕捉器 wirefinder 钢丝探测器 Go devil-F.B 平底撞棍 Go devil-C.B 刀杆撞棍 retriever 钢丝打捞器 overshot 卡瓦打捞筒 magnetic fishing tool 磁力打捞工具sidewall cutter 刮管刀 alligator grab 鳄鱼爪 sand bailer 捞沙筒 pipe wrench 管钳 tong chain 链钳 spanner 扳手 wireline clamp 钢丝夹 hay pulley 地滑轮 dump bailer 倾倒筒 saw 锯子 saw blade 锯条 punch 冲子 file 锉刀 flat file 板锉,扁锉 hammer 榔头 pliers,vice 老虎钳 wire cutter 断线钳forfex 剪刀 tongs 大钳,钳子,管钳 flat bit tongs 扁嘴钳 screwdriver 改锥，螺丝刀 wire stripper 剥皮钳,掳线钳 wire-stripper pliers 剥线钳 B. EQUIPMENT stuffing box 防喷盒 lubricator upper section 上防喷管 lubricator middle section 中防喷管 lubricator lower section 下防喷管 blowout preventer(BOP) 防喷器 wellhead adapter 井口变扣短节 Lincoln pump 林肯泵 hand pump assy.for stuffing box 手 压泵 Fire extinguisher 灭火器 hand tool box 手工具箱 injector 注油器 lifting cap BOP吊帽 trolly 防喷管支撑架 parasol 阳伞 work vice 台钳 chain block 链葫芦 tie down chain 系紧链 fixed pulley 定滑轮 wobble pump 手摇泵 wire line clamp 钢丝绳夹 wire rope sling 绳套,钢丝吊绳 winch 绞车 winch barrel(drum) 绞车滚筒 winch brake 绞车刹车 winch drive shaft universal joint 绞 车主动轴万向节 winch drum shaft 绞车滚动轴 winch line 吊装用绳套 winch control panel 绞车控制面板 winch truck 吊车 C. OPERATIONS RTTS Operation for Shoot and Pull RTTS完井服务 RTTS Operation for Cement Squeezing RTTS固井服务（挤水泥） Pulling Y Block 捞Y堵塞器 Open SSD(Slide Side Door) 开生产 滑套 Close SSD(Slide Side Door) 关生产 滑套 Open Circulating SSD(Slide Side Door) 开循环滑套 Close Circulating SSD(Slide Side Door) 关循环滑套 Running Gauge Cutter 通井 Clean up 地面完井放喷 Open Drain Valve 砸泻油阀 Pulling Test Plug 捞测试阀 Running Jet Pump 投射流泵 Pulling Jet Pump 捞射流泵 Running Flow Regulator 投配水器 Pulling Flow Regulator 捞配水器 Fishing Drop Bar 捞点火棒 Measuring Static Pressure 测静压 Measuring Flowing Pressure 测流压 Measuring BHPBU(Bottom Hole Pressure Build Up) 测压力恢复 Measuring BHP(Bottom Hole Pressure) Testing with Jet Pump 带 泵测压（射流泵） Multi-Rate BHP(Bottom Hole Pressure) Testing 系统试井 Slick-line Operation for Completion 钢丝配合完井服务 Slick-line Operation for acidizing 配 合酸化钢丝作业 Running Plug 投堵塞器 Pulling Plug 捞堵塞器 Run Impression Block 下铅印 Running Prong 投平衡杆 Sand Level detection 探沙面 Run Sand Bailer 下捞砂桶 Open SSSV(Sub Surface Safety Valve) by Force 强行打开井下安全 阀 Running Go Devil 剪切钢丝 Fishing Slickline 打捞钢丝 Running Side Pocket Plug 投偏心堵 塞器 Pulling Side pocket Plug 捞偏心堵 塞器 Running Side Pocket Check Valve 投 偏心阀 Pulling Side Pocket Check Valve 捞 偏心阀 Sand Sampling 取砂样 Stable Test 稳定试井 Slickline Swab 抽吸 Running Hanger 投悬挂器 Pulling Hanger 捞悬挂器 D. SPARE PARTS
海外钻井项目必备词汇REVISED
海外钻井项目必备英语词汇ESSENTIAL ENGLISH WORDS FOR OVERSEAS DRILLING PROJECTS 山东胜利职业学院 国际化人才培训部
目录 第一章：石油钻井工程英语基础词汇 第1节石油钻井工程基础词汇 (1) 第2节石油钻井方法基础词汇 (5) 第3节石油钻井技术基础词汇 (5) 第4节石油钻井参数基础词汇 (6) 第5节石油钻井作业现场工作人员名称 (7) 第 6 节石油作业现场常用工具 (8) 第二章：石油工程常用设备及专业术语 第1节钻井设备部分 (13) 第2节钻井泵类及相关设备 (16) 第3节与泵操作有关的实用短语 (18) 第4节钻台与底座 (19) 第5节井控操作与防喷器 (19) 第三章：钻井工程作业部分 第1节钻井事故 (24) 第2节钻头 (25) 第3节钻具 (25) 第4节钻井工程地面作业实用词汇与短语 (27) 第5节钻井工程井口作业实用词汇与短语 (28) 第四章：钻井液及相关设备 第1节钻井液名称 (30) 第2节钻井液设备 (31) 第3节钻井液处理剂 (31) 第五章：钻井相关作业 第1节取芯部分 (35) 第2节固井部分 (35) 第3节固井水泥浆名称和参数 (37) 第4节测井部分 (38) 第六章：井下作业常用短语 (39) 第七章：海上钻井作业 (41) 第八章：定向井部分 (42) 第九章：石油现场机械传动与机械设备 第1节：动力与传动 (43)
第十章：石油工程作业现场生活用词 第1节身体各部分名称 (45) 第2节服装 (47) 第3节描述天气 (49) 第4节常见蔬菜名称 (49) 第5节常见水果名称 (50) 第6节味道和调味品调味品 (50) 第7节酒类和祝酒 (51) 第8节食品 (52) 第9节超级市场 (53) 第10节容器、单位及钱币 (53) 第11节肉类 (54) 第12节海鲜，鱼类 (54) 第13节救火及救援 (55) 第14节日常生活用品 (55) 第15节星期与月份 (56) 第16节数字 (57) 第17节颜色 (58) 第十一章：常用缩略语与换算 第1节常用缩略语 Abbreviation (59) 第2节钻井现场常用公英制（美国用法）换算 (60)
石油钻井专业英语词汇
目录 第一节钻井英语单词 (2) 第二节井场用语，钻井常用短语及句子 (10) 第三节钻井泥浆术语 (29) 第四节常用安全术语 (31) 第五节钻井设备英语 (33) 第六节石油钻井英语情景会话 (40) 附录一：平台人员、作业者及服务公司人员名称 (47) 附录二：主要设备名称 (48) 附录三：钻具、井口工具、打捞工具名称 (52) 附录四：材料和工具名称 (53) 附录五：常用缩写形式 (55)
第一节钻井英语单词 drilling crew 钻井队 drill floor,rig floor,floor 钻台drawworks 绞车 well-site, rig-site 井场 rig manager 平台经理 DC (drill collar) 钻铤 drilling engineer 钻井工程师 DP (drill pipe) 钻杆 toolpusher 带班队长 rotary table 转盘 driller 司钻 assistant driller 副司钻derrickman, monkeyman 井架工roughneck, floorman 钻工roustabout 场地工 liner 缸套 motor fire man 司机（motorman）wellhead 井口 circulation & solid system 循环固控系统 machinist 机械师,机工,机械大班electrician 电器师,电工,电器大班operation program 作业程序(指令) cathead 猫头 caravan 营房，大篷车 tong 大钳 elevator 吊卡 well depth 井深 slip 卡瓦makeup 上扣 spud in 开钻 breakout 卸扣 ROP (rate of penetration),drilling speed, penetration rate 钻速 trip 起下钻 diesel-engine 柴油机 loss circulation 井漏，循环漏失working uniform 工作服 brake handle, brake bar 刹把 water well condition 水井井况circulating tank, circulation tank 循环罐 normal drilling 正常钻进 reserve tank 储备罐 parameter 参数 trip tank 补给罐，尖底罐, 起下钻泥浆罐（起下钻计量罐） rotary speed 转盘转速（转速）shale shaker 振动筛 pump pressure 泵压 WOB (weight on bit) 钻压 mesh 目,网孔;啮合,编织 torque 扭矩 screen cloth 筛布 displacement 排量 safety meeting 班前会 pump stroke 泵冲 shift exchange 交班、（倒班）