模具专业英文术语大全
模具英语专业术语
模具述语
一、入水：gate
进入位： gate location
水口形式：gate type
大水口：edge gate
细水口: pin—point gate
水口大小：gate size
转水口: switching runner/gate
唧嘴口径: sprue diameter
二、流道: runner
热流道： hot runner，hot manifold
热嘴冷流道: hot sprue/cold runner
唧嘴直流： direct sprue gate
圆形流道：round（full/half runner
流道电脑分析：mold flow analysis
流道平衡:runner balance
热嘴： hot sprue
热流道板:hot manifold
发热管：cartridge heater
探针: thermocouples
插头: connector plug
插座： connector socket
密封/封料: seal
三、运水：water line
喉塞：line lpug
喉管:tube
塑胶管:plastic tube
快速接头：jiffy quick connector
plug/socker
四、模具零件： mold components
三板模：3—plate mold
二板模：2—plate mold
边钉/导边:leader pin/guide pin
边司/导套：bushing/guide bushing
中托司:shoulder guide bushing
中托边L：guide pin
顶针板：ejector retainner plate
托板： support plate
螺丝: screw
管钉：dowel pin
开模槽：ply bar scot
内模管位：core/cavity inter—lock
顶针： ejector pin
司筒：ejector sleeve
司筒针：ejector pin
推板：stripper plate
缩呵：movable core，return core core puller
扣机（尼龙拉勾）：nylon latch lock
斜顶:lifter
模胚（架)： mold base
上内模：cavity insert
下内模：core insert 行位（滑块）: slide
镶件：insert
压座/斜鸡:wedge
耐磨板/油板：wedge wear plate
压条：plate
撑头： support pillar
唧嘴： sprue bushing
挡板:stop plate
定位圈：locating ring
锁扣：latch
扣鸡：parting lock set
推杆：push bar
栓打螺丝：S。H.S。B
顶板：eracuretun
活动臂：lever arm
分流锥：spure sperader
水口司:bush
垃圾钉：stop pin
隔片:buffle
弹弓柱：spring rod
弹弓：die spring
中托司:ejector guide bush
中托边：ejector guide pin
镶针:pin
销子：dowel pin
波子弹弓：ball catch
喉塞： pipe plug
锁模块：lock plate
斜顶：angle from pin
斜顶杆：angle ejector rod
尼龙拉勾：parting locks
活动臂：lever arm
复位键、提前回杆:early return bar
气阀：valves
斜导边:angle pin
术语：terms
承压平面平衡:parting surface support balance
模排气：parting line venting
回针碰料位：return pin and cavity interference
模总高超出啤机规格：mold base shut hight
顶针碰运水:water line interferes withejector pin
料位出上/下模：part from cavith （core) side
模胚原身出料位：cavity direct cut on A-plate，core direct cut
on B-plate。
不准用镶件: Do not use (core/cavity) insert 用铍铜做镶件: use beryllium copper insert 初步（正式）模图设计:preliinary (final）mold design
反呵：reverse core
弹弓压缩量：spring compressed length 稳定性好：good stability，stable
强度不够:insufficient rigidity
均匀冷却：even cooling
扣模:sticking
热膨胀:thero expansion
公差:tolorance
铜公（电极）：copper electrode
Mold ＆ die components 模具单元
Mold changing systems 换模系统
Mold core 模芯
Mold heaters/chillers 模具加热器/冷却器Mold polishing/texturing 模具打磨/磨纹Mold repair 模具维修
Molds 模具
Pressing dies 压模
Quick die change systems 速换模系统Quick mold change systems 快速换模系统三、模具
塑料模具 mould of plastics
注塑模具injection mould
冲压模具die
模架mould base
定模座板Top clamping plate
Top plate
Fixed clamp plate
水口推板stripper plate
A 板A plate
B 板B plate
支承板 support plate
方铁 spacer plate
底针板 ejector plate
面针板 ejector retainer plate
回针 Return pin
导柱 Guide pin
有托导套 Shoulder Guide bush
直导套 Straight Guide bush
动模座板Bottom clamp plate
Moving clamp plate
基准线datum line
基准面datum plan
型芯固定板core—retainer plate
凸模固定板punch—retainer plate
顶针ejector pin
单腔模具single cavity mould
多腔模具multi-cavity mould
多浇口multi—gating
浇口gate
缺料starving
排气breathing
光泽gloss
合模力mould clamping force
锁模力mould locking force 挤出extrusion
开裂crack
循环时间cycle time
老化aging
螺杆screw
麻点pit
嵌件insert
活动镶件movable insert
起垩chalking
浇注系统feed system
主流道 sprue
分流道runner
浇口gate
直浇口direct gate ， sprue gate
轮辐浇口spoke gate ， spider gate
点浇口pin—point gate
测浇口edge gate
潜伏浇口submarine gate , tunnel gate
料穴cold-slug well
浇口套sprue bush
流道板runner plate
排飞槽vent
分型线（面）parting line
定模stationary mould,Fixed mould
动模movable mould, movable half
上模upper mould, upper half
下模lower mould， lower half
型腔cavity
凹模cavity plate，cavity block
拼块split
定位销dowel
定位销孔dowel hole
型芯core
斜销angle pin, finger cam
滑块slide
滑块导板slide guide strip
楔紧块heel block, wedge lock
拉料杆sprue puller
定位环locating ring
冷却通cooling channel
脱模斜度draft
滑动型芯slide core
螺纹型芯threaded core
热流道模具hot—runner mould
绝热流道模insulated runner mould
熔合纹weld line （flow line）
三板式模具 three plate mould
脱模ejection
换模腔模具 interchangeable cavity mould 脱模剂release agent
注射能力shot capacity
注射速率injection rate
注射压力injection pressure
差色剂colorant
保压时间holdup time
闭模时间closing time
定型装置sizing system
阴模female mould，cavity block
阳模male mould
电加工设备Electron Discharge Machining 数控加工中心CNC machine center
万能铁床Universal milling machine
卧式刨床Horizontal planer
车床Engine lathe
平面磨床Surface grinding machine
去磁机Demagnetization machine
万能摇臂钻床Universal radial movable driller
立式钻床Vertical driller
超声波清洗机Ultrasonic clearing machine compre sion molding 压缩成型
flash mold 溢流式模具
plsitive mold 挤压式模具
split mold 分割式模具
cavity 型控母模
core 模心公模
taper 锥拔
leather cloak 仿皮革
shiver 饰纹
flow mark 流痕
welding mark 溶合痕
post screw insert 螺纹套筒埋值
self tapping screw 自攻螺丝
striper plate 脱料板
piston 活塞
cylinder 汽缸套
chip 细碎物
handle mold 手持式模具
(移转成型用模具）
encapsulation molding 低压封装成型
（射出成型用模具)
two plate 两极式（模具）
well type 蓄料井
insulated runner 绝缘浇道方式
hot runner 热浇道
runner plat 浇道模块
valve gate 阀门浇口
band heater 环带状的电热器
spindle 阀针
spear head 刨尖头
slag well 冷料井
cold slag 冷料渣
air vent 排气道
welding line 熔合痕
eject pin 顶出针
knock pin 顶出销return pin 回位销反顶针
sleave 套筒
stripper plate 脱料板
insert core 放置入子
runner stripper plate 浇道脱料板guide pin 导销
eject rod （bar）(成型机）顶业捧subzero 深冷处理
three plate 三极式模具
runner system 浇道系统
stress crack 应力电裂orientation 定向
sprue gate 射料浇口，直浇口nozzle 射嘴
sprue lock pin 料头钩销（拉料杆) slag well 冷料井
side gate 侧浇口
edge gate 侧缘浇口
tab gate 搭接浇口
film gate 薄膜浇口
flash gate 闸门浇口
slit gate 缝隙浇口
fan gate 扇形浇口
dish gate 因盘形浇口
diaphragm gate 隔膜浇口
ring gate 环形浇口
subarine gate 潜入式浇口
tunnel gate 隧道式浇口
pin gate 针点浇口
Runner less 无浇道
（sprue less)无射料管方式
long nozzle 延长喷嘴方式
sprue 浇口;溶渣
emboss 凸点
dome 凸圆
semi-shearing 半剪
stamp mark 冲记号
deburr or coin 压毛边
punch riveting 冲压铆合
side stretch 侧冲压平
reel stretch 卷圆压平
groove 压线
blanking 下料
stamp letter 冲字（料号) shearing 剪断
tick—mark nearside 正面压印
tick-mark farside 反面压印
冲压名称类
extension dwg 展开图
procedure dwg 工程图
die structure dwg 模具结构图material 材质
material thickness 料片厚度
factor 系数
upward 向上
downward 向下
press specification 冲床规格
die height range 适用模高
die height 闭模高度
burr 毛边
gap 间隙
weight 重量
total wt.总重量
punch wt。上模重量
五金零件类
inner guiding post 内导柱
inner hexagon screw 内六角螺钉dowel pin 固定销
coil spring 弹簧
lifter pin 顶料销
eq-height sleeves=spool 等高套筒pin 销
lifter guide pin 浮升导料销
guide pin 导正销
wire spring 圆线弹簧
outer guiding post 外导柱
stop screw 止付螺丝
located pin 定位销
outer bush 外导套
模板类
top plate 上托板（顶板）
top block 上垫脚
punch set 上模座
punch pad 上垫板
punch holder 上夹板
stripper pad 脱料背板
up stripper 上脱料板
male die 公模(凸模）
feature die 公母模
female die 母模（凹模)
upper plate 上模板
lower plate 下模板
die pad 下垫板
die holder 下夹板
die set 下模座
bottom block 下垫脚
bottom plate 下托板(底板)
stripping plate 内外打(脱料板)
outer stripper 外脱料板
inner stripper 内脱料板
lower stripper 下脱料板
零件类
punch 冲头
insert 入块（嵌入件）
deburring punch 压毛边冲子
groove punch 压线冲子
stamped punch 字模冲子
round punch 圆冲子
special shape punch 异形冲子
bending block 折刀
roller 滚轴
baffle plate 挡块
located block 定位块
supporting block for location
定位支承块
air cushion plate 气垫板
air-cushion eject—rod 气垫顶杆
trimming punch 切边冲子
stiffening rib punch = stinger 加强筋冲子
ribbon punch 压筋冲子
reel-stretch punch 卷圆压平冲子
guide plate 定位板
sliding block 滑块
塑料模具专业术语
动模 movable mould moving half
定模座板 fixed clamp plate, top clamping plate. top plate
动模座板 moving clamp plate. bottom clamping plate。 bottom plate
上模座板 upper clamping plate
下模座板 lower clamping plate
凹模固定板 cavity—retainer plate
型芯固定板 core-retainer plate
凸模固定板 punch-retainer plate
模套 chase. bolster. frame
支承板 backing plate。 supprr plate 垫块 spacer parallel
支架 ejector housing. mould base leg 压力铸造模具 die-casting die 压铸模零部件
定模 fixed die, cover die
定模座板 fixed clamping plate
定模套板 bolstor, fixed die
动模 moving die，ejector die
动模座板 moving clamping plate
直流道 sprue
横流道 runner
内浇口 gate
landed plunger mold｜|有肩柱塞式模具burnishing die｜｜挤光模
landed positive mold|｜有肩全压式模具button die|｜镶入式圆形凹模
loading shoe mold||料套式模具
center—gated mold｜|中心浇口式模具loose detail mold||活零件模具
chill mold||冷硬用铸模
loose mold||活动式模具
clod hobbing||冷挤压制模
louvering die||百叶窗冲切模
composite dies｜｜复合模具
manifold die|｜分歧管模具
counter punch｜|反凸模
modular mold｜|组合式模具
double stack mold|｜双层模具
multi-cavity mold｜｜多模穴模具electroformed mold｜|电铸成形模multi—gate mold||复式浇口模具expander die||扩径模
offswt bending die｜｜双折冷弯模具extrusion die||挤出模
palletizing die||叠层模
family mold|｜反套制品模具
plaster mold|｜石膏模
blank through dies||漏件式落料模porous mold｜|通气性模具
duplicated cavity plate｜|复板模positive mold|｜全压式模具
fantail die|｜扇尾形模具
pressure die｜|压紧模
fishtail die||鱼尾形模具
pro轮廓模
flash mold||溢料式模具
progressive die||顺序模
gypsum mold|｜石膏铸模
protable mold||手提式模具
hot-runner mold||热流道模具
prototype mold||雏形试验模具
ingot mold｜｜钢锭模
punching die|｜落料模
lancing die｜｜切口模
raising（embossing）｜｜压花起伏成形re—entrant mold|｜倒角式模具sectional die｜|拼合模
runless injection mold|｜无流道冷料模具sectional die｜｜对合模具
segment mold｜｜组合模semi—positive mold||半全压式模具shaper｜|定型模套
single cavity mold|｜单腔模具
solid forging die｜｜整体锻模
split forging die｜|拼合锻模
split mold｜|双并式模具
sprueless mold｜|无注道残料模具squeezing die|｜挤压模
stretch form die｜|拉伸成形模sweeping mold｜｜平刮铸模swing die||振动模具
three plates mold|｜三片式模具
trimming die｜｜切边模
unit mold||单元式模具
universal mold||通用模具
unscrewing mold｜｜退扣式模具
yoke type die｜｜轭型模
模具钢材 khu?n thép
alloy tool steel 合金工具钢
aluminium alloy 铝合金钢
bearing alloy 轴承合金
blister steel 浸碳钢
bonderized steel sheet 邦德防蚀钢板carbon tool steel 碳素工具钢
clad sheet 被覆板
clod work die steel 冷锻模用钢
emery 金钢砂
ferrostatic pressure 钢铁水静压力
forging die steel 锻造模用钢
galvanized steel sheet 镀锌铁板
hard alloy steel 超硬合金钢
high speed tool steel 高速度工具钢
hot work die steel 热锻模用钢
low alloy tool steel 特殊工具钢
low manganese casting steel 低锰铸钢marging steel 马式体高强度热处理钢martrix alloy 马特里斯合金
meehanite cast iron 米汉纳铸钢meehanite metal 米汉纳铁
merchant iron 市售钢材
molybdenum high speed steel 钼系高速钢molybdenum steel 钼钢
nickel chromium steel 镍铬钢prehardened steel 顶硬钢
silicon steel sheet 矽钢板
stainless steel 不锈钢
tin plated steel sheet 镀锡铁板
tough pitch copper 韧铜
troostite 吐粒散铁
tungsten steel 钨钢
vinyl tapped steel sheet 塑胶覆面钢板
塑件及模具
compre sion molding压缩成型
flash mold溢流式模具
plsitive mold挤压式模具
split mold分割式模具
cavity型控母模
core模心公模
taper锥拔
leather cloak仿皮革
shiver饰纹
flow mark流痕
welding mark溶合痕
post screw insert螺纹套筒埋值
self tapping screw自攻螺丝
striper plate脱料板
piston活塞
cylinder汽缸套
chip细碎物
handle mold手持式模具
（移转成型用模具）encapsulation molding低压封装成型（射出成型用模具)
two plate两极式(模具）
well type蓄料井
insulated runner绝缘浇道方式
hot runner热浇道
runner plat浇道模块
valve gate阀门浇口
band heater环带状的电热器spindle阀针
spear head刨尖头
slag well冷料井
cold slag冷料渣
air vent排气道
welding line熔合痕
eject pin顶出针
knock pin顶出销
return pin回位销反顶针
sleave套筒
stripper plate脱料板
insert core放置入子
runner stripper plate浇道脱料板guide pin导销
eject rod (bar)(成型机）顶业捧subzero深冷处理
three plate三极式模具
runner system浇道系统
stress crack应力电裂
orientation定向
sprue gate射料浇口，直浇口nozzle射嘴
sprue lock pin料头钩销（拉料杆）slag well冷料井
side gate侧浇口
edge gate侧缘浇口
tab gate搭接浇口
film gate薄膜浇口
flash gate闸门浇口
slit gate缝隙浇口
fan gate扇形浇口
dish gate因盘形浇口
diaphragm gate隔膜浇口
ring gate环形浇口
subarine gate潜入式浇口tunnel gate隧道式浇口
pin gate针点浇口
Runner less无浇道
（sprue less)无射料管方式
long nozzle延长喷嘴方式
sprue浇口;溶渣
零件类
punch冲头
insert入块（嵌入件）
deburring punch压毛边冲子
groove punch压线冲子
stamped punch字模冲子
round punch圆冲子
special shape punch异形冲子
bending block折刀
roller滚轴
baffle plate挡块
located block定位块
supporting block for location
定位支承块
air cushion plate气垫板
air-cushion eject—rod气垫顶杆trimming punch切边冲子
stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子
reel—stretch punch卷圆压平冲子guide plate定位板
sliding block滑块
sliding dowel block滑块固定块
active plate活动板
lower sliding plate下滑块板
upper holder block上压块
upper mid plate上中间板
spring box弹簧箱
spring—box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套
cover plate盖板
guide pad导料块
模板类
top plate上托板(顶板）
top block上垫脚
punch set上模座
punch pad上垫板
punch holder上夹板
stripper pad脱料背板
up stripper上脱料板
male die公模(凸模)
feature die公母模
female die母模（凹模)
upper plate上模板
lower plate下模板
die pad下垫板
die holder下夹板
die set下模座
bottom block下垫脚
bottom plate下托板（底板) stripping plate内外打(脱料板) outer stripper外脱料板
inner stripper内脱料板
lower stripper下脱料板
plain die简易模
pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔
forming成型(抽凸,冲凸）draw hole抽孔
bending折弯
trim切边
emboss凸点
dome凸圆semi—shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线
blanking下料stamp letter冲字(料号) shearing剪断
tick—mark nearside正面压印tick-mark farside反面压印
冲压名称类
extension dwg展开图procedure dwg工程图
die structure dwg模具结构图material材质
material thickness料片厚度factor系数
upward向上
downward向下
press specification冲床规格die height range适用模高die height闭模高度
burr毛边
gap间隙
weight重量
total wt。总重量
punch wt.上模重量
连接器connector
端子terminal
条型连接器bar connector
阴连接器Housing
阳连接器wafer
线束wire harness
间距space
额定电压 rated voltage
额定电流 rated current
接触电阻contact resistance 绝缘电阻insulation resistance 超声波焊接ultrasonic welding 耐压withstand voltage
针pin
物料编号part number
导线wire
基体金属Base metal
电缆夹cable clamp
倒角chamfer
接触面积contact area
接触件安装孔contact cavity 接触长度contact length
接触件电镀层contact plating 接触压力contact pressure
接触件中心距contact space 接触簧片contact spring
插孔socket contact
法兰、凸缘Flange
界面间隙interfacial gap
键Key
键槽keyway
过渡段ramp
屏蔽套shielding
定位基准Datum reference
扁平电缆flat cable ，Ribbon cable
柔性印刷电线Flexible printed wiring
多层印制电路Multilayer printed circuit
焊盘pad
图形pattern
间距pitch
负极Negative pole
正极positive pole
回流Reflow
原理图Schematic diagram
单面板single sided board
双面板Two—sided board，Double-sided board
表面安装surface Mounting
翘曲warp， bow
波峰焊wave soldering
模具专业英文术语大全
模具英语专业术语 模具述语 一、入水：gate 进入位： gate location 水口形式：gate type 大水口：edge gate 细水口： pin-point gate 水口大小：gate size 转水口： switching runner/gate 唧嘴口径： sprue diameter 二、流道: runner 热流道： hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形流道：round(full/half runner 流道电脑分析：mold flow analysis 流道平衡:runner balance 热嘴： hot sprue 热流道板：hot manifold 发热管：cartridge heater 探针: thermocouples 插头： connector plug 插座： connector socket 密封/封料： seal 三、运水：water line 喉塞：line lpug 喉管：tube 塑胶管：plastic tube 快速接头：jiffy quick connector plug/socker 四、模具零件： mold components 三板模：3-plate mold 二板模：2-plate mold 边钉/导边：leader pin/guide pin 边司/导套：bushing/guide bushing 中托司：shoulder guide bushing 中托边L：guide pin 顶针板：ejector retainner plate 托板： support plate 螺丝： screw 管钉：dowel pin 开模槽：ply bar scot 内模管位：core/cavity inter-lock 顶针： ejector pin 司筒：ejector sleeve 司筒针：ejector pin 推板：stripper plate 缩呵：movable core,return core core puller 扣机（尼龙拉勾）：nylon latch lock 斜顶：lifter 模胚（架）： mold base 上内模：cavity insert 下内模：core insert 行位（滑块）： slide 镶件：insert 压座/斜鸡：wedge 耐磨板/油板：wedge wear plate 压条：plate 撑头: support pillar 唧嘴： sprue bushing 挡板：stop plate 定位圈：locating ring 锁扣：latch 扣鸡：parting lock set 推杆：push bar 栓打螺丝：S.H.S.B 顶板：eracuretun 活动臂：lever arm 分流锥：spure sperader 水口司:bush 垃圾钉：stop pin 隔片：buffle 弹弓柱：spring rod 弹弓:die spring 中托司：ejector guide bush 中托边：ejector guide pin 镶针：pin 销子：dowel pin 波子弹弓：ball catch 喉塞: pipe plug
冲压模具专业词汇中英文翻译
Counter bored hole 沉孔 Chamfer 倒斜角 Fillet 倒圆角 padding block垫块 stepping bar垫条 upper die base上模座 lower die base下模座 upper supporting blank上承板 upper padding plate blank上垫板 spare dies模具备品 spring 弹簧 bolt螺栓 document folder活页夹 file folder资料夹 to put file in order整理资料 spare tools location手工备品仓 first count初盘人 first check初盘复棹人 second count 复盘人 second check复盘复核人 equipment设备 waste materials废料 work in progress product在制品 casing = containerization装箱 quantity of physical inventory second count 复盘点数量 Quantity of customs count 会计师盘,点数量 the first page第一联 filed by accounting department for reference会计部存查 end-user/using unit(department)使用单位 Summary of year-end physical inventory bills 年终盘点截止单据汇总表 bill name单据名称 This sheet and physical inventory list will be sent to accounting department together (Those of NHK will be sent to financial department) 本表请与盘点清册一起送会计部－(NHK厂区送财会部) Application status records of year-end physical inventory List and physical inventory card 年终盘点卡与清册使用－状况明细表 blank and waste sheet NO. 空白与作废单号
塑胶模具类中英文对照专业术语
塑胶模具类中英文对照专业术语工程部/ Design department: 1) Designer - 设计师。 2) Assembly drawing - 模具组装图。 3) Mold layout - 模具结构图。 4) 2D product drawing - 2D产品图。 5) 3D product data - 3D产品数据。 6) Part drawing - 散件图。 7) Insert molding - 镶件模。 8) 2 color mold / Double injection tool - 双色模。 9) Hydraulic system - 油/水压系统。 10) Parting line - 分模线。 11) Air venting - 排气槽。 12) Cooling system - 冷却系统。 13) Screw - 镙丝。 14) Hot runner system - 热流道。 15) Valve gate - 伐针入水口。 16) Fan gate - 扇型入水口。 17) Pin point gate - 针点进胶。 18) Moon gate / Banana gate - 香蕉，象牙入水口。 19) Submarine gate - 潜水口。 20) Injection machine tonnage - 注塑机吨数。 21) Number of cavity - 穴数。 22) Steel - 钢材。 23) Copper - 铜。 24) Tungsten copper - 钨铜。 25) Beryllium copper - 铍铜。 26) Hardening - 加硬/淬火。 27) Tempering - 回火。
模具常用术语中英文对照
模芯 Parting Core 耐落胶 Teflon Paste 局部视图 Partial View 偏移量 Offset 冷料 Cold Slag 水塞 Water Line Plug 线切割 Wire 撬模脚 Ppy Slot 轮廓 Contour 重新加工 Reworked 螺纹孔Tapping Hole 配件 Components 连接件 Fittings 补偿 Compensation 斜针 Angle Pin 平面度 Parallel 接合 Engage 倒角Chamfer 替换镶件Interchangeable Mold Inserts 模胚 Mold Base 指定吨位的注塑机 Specific Press 热嘴Hotnozzle 水嘴接头 Water Fitting 火花机 Edm 螺纹 Eyebolt Thread 熔接线 Weildline 回针 Stop Pin 压机 Press 二级顶出针 Sub-Leaderd Pin 嗮纹 Texturing 镶件 Mold Insert 梯形 Trapezoid
加硬 Harden 凸缘、法兰 Flange 唧嘴 Sprue 方铁 Spacer Block 设计筒图 Design Preliminary 顶针板 Ejector Plate 名称块表 Title Block 顶针底板 Ejector Retainer Plate 版本标识 Revision Level 垫板 Retainer Plate 材料清单 Stock List 后模镶针 Core Pin 制模 Build Mold 垃圾钉 Stop Pin 手动滑块 Hand Slide 有托顶针 Shoulder Ejector Pin 漏水测试 Leak Test 顶针板导套Guided Ejection Bushing 流道排气 Runner Vents 针板导柱 Guided Ejection Leader Pin 抛光 Draw Polish 唧嘴 Sprue Bushing 侧抽芯 Slide Action 三板模延伸式唧嘴 Extension Noozzle Bulishing 加强筋 Reinforcing 水口板导套 Runner Stripper Pin 三角撑 Gusset 定位圈（法兰）Locating Ring 柱子 Bossed 管钉（定位销）Dowel Pin 出模斜度 Draft 管状管钉 Tubular Dowel
机械专业术语英文翻译
陶瓷 ceramics 合成纤维 synthetic fibre 电化学腐蚀 electrochemical corrosion 车架 automotive chassis 悬架 suspension 转向器 redirector 变速器 speed changer 板料冲压 sheet metal parts 孔加工 spot facing machining 车间 workshop 工程技术人员 engineer 气动夹紧 pneuma lock 数学模型 mathematical model 画法几何 descriptive geometry 机械制图 Mechanical drawing 投影 projection 视图 view 剖视图 profile chart 标准件 standard component 零件图 part drawing 装配图 assembly drawing 尺寸标注 size marking
技术要求 technical requirements 刚度 rigidity 内力 internal force 位移 displacement 截面 section 疲劳极限 fatigue limit 断裂 fracture 塑性变形 plastic distortion 脆性材料 brittleness material 刚度准则 rigidity criterion 垫圈 washer 垫片 spacer 直齿圆柱齿轮 straight toothed spur gear 斜齿圆柱齿轮 helical-spur gear 直齿锥齿轮 straight bevel gear 运动简图 kinematic sketch 齿轮齿条 pinion and rack 蜗杆蜗轮 worm and worm gear 虚约束 passive constraint 曲柄 crank 摇杆 racker 凸轮 cams
模具专业英文术语大全
实用文案 模具英语专业术语 模具述语开模槽：ply bar scot 内模管位：一、入水：gate core/cavity inter-lock 顶针：ejector pin 进入位：gate location 司筒：ejector sleeve 水口形式：gate type 司筒针：edge gate ejector pin 大水口：推板：细水口：stripper plate pin-point gate 缩呵：gate size movable core,return core core 水口大小：puller switching runner/gate 转水口：扣机（尼龙拉勾）：nylon latch lock sprue diameter 唧嘴口径：斜顶：lifter : runner 二、流道模胚（架）：mold base hot runner,hot manifold 热流道：上内模：cavity insert : hot sprue/cold runner 热嘴冷流道下内模：core insert : direct sprue gate 唧嘴直流行位（滑块）：slide round(full/half runner 圆形流道：镶件：insert mold flow analysis 流道电脑分析：压座/斜鸡：wedge :runner balance 流道平衡耐磨板/油板：wedge wear plate hot sprue 热嘴：压条：plate hot manifold 热流道板：撑头: support pillar cartridge heater 发热管：唧嘴：sprue bushing : thermocouples 探针挡板：stop plate connector plug 插头：定位圈：locating ring connector socket 插座：锁扣：latch seal 封料：/密封扣鸡：parting lock set water line 三、运水：推杆：push bar line lpug 喉塞：栓打螺丝：S.H.S.B tube 喉管：顶板：eracuretun plastic tube 塑胶管：活动臂：lever arm jiffy quick connector 快速接头：分流锥：spure sperader plug/socker 水口司mold components 四、模具零件：:bush 垃圾钉：三板模：3-plate mold stop pin 隔片：buffle 二板模：2-plate mold 弹弓柱：导边：/leader pin/guide pin spring rod 边钉弹弓:die spring 导套：边司/bushing/guide bushing 中托司：ejector guide bush 中托司：shoulder guide bushing 中托边：ejector guide pin guide pin ：L中托边镶针：ejector retainner plate 顶针板：pin 销子：托板：support plate dowel pin 波子弹弓：ball catch screw 螺丝：: pipe plug dowel pin 管钉：喉塞文案大全． 实用文案 锁模块：lock plate Mold repair 模具维修 angle from pin 斜顶：Molds 模具
机械专业外文翻译中英文翻译
外文翻译 英文原文 Belt Conveying Systems Development of driving system Among the methods of material conveying employed，belt conveyors play a very important part in the reliable carrying of material over long distances at competitive cost．Conveyor systems have become larger and more complex and drive systems have also been going through a process of evolution and will continue to do so．Nowadays，bigger belts require more power and have brought the need for larger individual drives as well as multiple drives such as 3 drives of 750 kW for one belt(this is the case for the conveyor drives in Chengzhuang Mine)．The ability to control drive acceleration torque is critical to belt conveyors’ performance．An efficient drive system should be able to provide smooth，soft starts while maintaining belt tensions within the specified safe limits．For load sharing on multiple drives．torque and speed control are also important consideratio ns in the drive system’s design. Due to the advances in conveyor drive control technology，at present many more reliable．Cost-effective and performance-driven conveyor drive systems cov ering a wide range of power are available for customers’ choices[1]. 1 Analysis on conveyor drive technologies 1．1 Direct drives Full-voltage starters．With a full-voltage starter design，the conveyor head shaft is direct-coupled to the motor through the gear drive．Direct full-voltage starters are adequate for relatively low-power, simple-profile conveyors．With direct fu11-voltage starters．no control is provided for various conveyor loads and．depending on the ratio between fu11- and no-1oad power requirements，empty starting times can be three or four times faster than full load．The maintenance-free starting system is simple，low-cost and very reliable．However, they cannot control starting torque and maximum stall torque；therefore．they are
机械术语英文翻译
机械术语英文翻译 阿基米德蜗杆Archimedes worm 安全系数safety factor; factor of safety安全载荷safe load 凹面、凹度concavity扳手wrench 板簧flat leaf spring 半圆键woodruff key 变形deformation摆杆oscillating bar 摆动从动件oscillating follower 摆动从动件凸轮机构cam with oscillating follower 摆动导杆机构oscillating guide-bar mechanism 摆线齿轮cycloidal gear摆线齿形cycloidal tooth profile 摆线运动规律cycloidal motion 摆线针轮cycloidal-pin wheel包角angle of contact 保持架cage背对背安装丨back-to-back arrangement 背锥back cone ；normal cone 背锥角back angle背锥距back cone distance比例尺scale 热容specific heat capacity 闭式链closed kinematic chain闭链机构closed chain mechanism 臂部arm 变频器frequency converters变频调速frequency control of motor speed 变速speed change 变速齿轮change gear ; change wheel变位齿轮modified gear变位系数modification coefficient 标准齿轮standard gear标准直齿轮standard spur gear 表面质量系数superficial mass factor 表面传热系数surface coefficient of heat transfer 表面粗糙度surface roughness 并联式组合combination in parallel并联机构parallel mechanism 并联组合机构parallel combined mechanism并行工程concurrent engineering 并行设计concurred design, CD不平衡相位phase angle of unbalance 不平衡imbalance (or unbalance)不平衡量amount of unbalance 不完全齿轮机构intermittent gearing波发生器wave generator 波数number of waves补偿compensation 参数化设计parameterization design, PD残余应力residual stress 操纵及控制装置operation control device槽轮Geneva wheel 槽轮机构Geneva mechanism ；Maltese cross槽数Geneva numerate 槽凸轮groove cam侧隙backlash 差动轮系differential gear train差动螺旋机构differential screw mechanism 差速器differential常用机构conventional mechanism; mechanism in common use 车床lathe承载量系数bearing capacity factor 承载能力bearing capacity成对安装paired mounting 尺寸系列dimension series齿槽tooth space 齿槽宽spacewidth齿侧间隙backlash 齿顶高addendum齿顶圆addendum circle 齿根高dedendum齿根圆dedendum circle 齿厚tooth thickness齿距circular pitch 齿宽face width齿廓tooth profile 齿廓曲线tooth curve齿轮gear 齿轮变速箱speed-changing gear boxes齿轮齿条机构pinion and rack 齿轮插刀pinion cutter; pinion-shaped shaper cutter齿轮滚刀hob ,hobbing cutter 齿轮机构gear齿轮轮坯blank 齿轮传动系pinion unit齿轮联轴器gear coupling 齿条传动rack gear齿数tooth number 齿数比gear ratio齿条rack 齿条插刀rack cutter; rack-shaped shaper cutter齿形链、无声链silent chain 齿形系数form factor齿式棘轮机构tooth ratchet mechanism 插齿机gear shaper重合点coincident points 重合度contact ratio冲床punch
机械专业相关词汇中英文翻译大全
机械专业相关词汇中英文翻译大全 单价unit price 工日合计Man-day total/work-day total 人工费cost of labor 材料费materials expenses 机械的mechanical 检查接线connection test 发电机generator 调相机phase regulator 周波cycle 减负荷装置 load-shedding equipment 断路器柜circuit breaker cabinet 单母线single busbar 互感器transformer 每相电流Current by Phase 封闭式插接close type socket joint 发电机控制面板generator control panel 分级卸载sorted unloading 同步控制synchronization control 调速器 speed governor 信号屏signal screen 继电器relay 高压柜high pressure cabinet 油浸电力变压器oil-immersed power transformer 空气断路器air circuit breaker 控制屏control panel 直流馈电屏direct current feed control panel 电容器electric condenser 计量盘metering panel 成套配电箱whole set of distribution box 落地式floor model 控制开关Control switches 铜芯电力电缆Copper core power cable 控制电缆actuating cable 热缩式电力电缆终端头pyrocondensation power cable terminal 钢结构支架配管steel structure bracket tubing 万用槽钢versatile U-steel 电缆托架 cable bracket 钢制托盘式桥架steel Tray-type cable support system waterproof socket 防水插座 防爆插座Explosion-proof socket 接地绞线earthing twisted pair 接地母线 earthing bus
模具常用术语中英文对照表
"R，L Co.,Ltd" 模具常用术语中英文对照 模芯Parting Core 局部视图Partial View 冷料# Cold Slag 线切割 Wire 轮廊Contour 螺纹孔 Tapping Hole 连接件 Fittings 斜针Angle Pin 接合Engage 替换镶件Interchangeable Mold Inserts 指定吨位的注塑机Specific Press 水嘴接头Water Fittings 螺纹Eyebolt Thread 回针Stop Pin 二级顶出针Sub-Leaderd Pin 镶件Mold Insert 加硬Harden 唧嘴Sprue 设计筒图Design Preliminary 名称块表Title Block 版本标识Revision Level 材料清单Stock List 制模Build Mold 手动滑块Hand Slide 漏水测试Leak Test 流道排气Runner Vents 抛光Draw Polish 侧抽芯 Side Action 加强筋 Reinforcing
三角撑 Gusset 柱子Bossed 出模斜度Draft 外廊Contour 落单会议Kick-Off Meeting 装卸孔 Handling Hole 运输安全带Moldstrap 码模槽 Clamp Slot 撑头Support Pillar 螺牙1/2-13 Eye Bolt 1/2-13Tap 导柱位 Leader Pin Location 耐落胶 Teflon Paste 偏移量 Offset 水塞Water Line Plug 撬模脚 Ppy Slot 重新加工Reworked 配件Components 补偿Compensation 平面度 Parallel 倒角Chamfer 模胚Mold Base 热嘴Hotnozzle 火花机 Edm 熔接线 Weildline 压机Press 晒纹Texturing 梯形Trapezoid 凸缘、法兰Flange 方铁Spacer Block 顶针板Ejector Plate 顶针底板Ejector Retainer Plate 垫板Retainer Plate
模具英语专业术语
模具英语专业术语模具的分类: 冲压模(五金模): stamping die 分离模: cutting die 成形模: forming die 塑胶模: plastics mold 注射模: injection mold 压缩模: compression mold 铸塑模: transfer mold 吹塑模: blow mold 吸塑模: suck mold 铸造模: casting die 砂型铸造: sand casting 压铸模: die casting 锻造模: forging die 塑胶模具术语 一、入水：gate 进入位(入水点)：gate location 水口形式：gate type 大水口(侧浇口): edge gate 潜水口: sub-gate 薄膜式水口: film gate 牛角式潜水口: banana gate 扇形水口: fan gate 环形水口: ring gate 二次水口: 细水口：pin-point gate 水口大小：gate size 转水口：switching runner/gate 唧嘴口径：sprue diameter 直接水口: direct gate 二、流道: runner 热流道：hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形(整圆/半圆)流道：round(full/half) runner 矩形流道: rectangle runner 梯形流道: trapezoid runner U形流道: U shape runner 流道电脑分析(模流分析)：mold flow analysis 流道平衡: runner balance
机械专业术语英文翻译
机械专业英语词汇 陶瓷ceramics 合成纤维synthetic fibre 电化学腐蚀electrochemical corrosion 车架automotive chassis 悬架suspension 转向器redirector 变速器speed changer 板料冲压sheet metal parts 孔加工spot facing machining 车间workshop 工程技术人员engineer 气动夹紧pneuma lock 数学模型mathematical model 画法几何descriptive geometry 机械制图Mechanical drawing 投影projection 视图view 剖视图profile chart 标准件standard component 零件图part drawing 装配图assembly drawing 尺寸标注size marking 技术要求technical requirements 刚度rigidity 内力internal force 位移displacement 截面section 疲劳极限fatigue limit 断裂fracture 塑性变形plastic distortion 脆性材料brittleness material 刚度准则rigidity criterion 垫圈washer 垫片spacer 直齿圆柱齿轮straight toothed spur gear 斜齿圆柱齿轮helical-spur gear 直齿锥齿轮straight bevel gear 运动简图kinematic sketch 齿轮齿条pinion and rack 蜗杆蜗轮worm and worm gear 虚约束passive constraint 曲柄crank
模具专业英文术语大全
模具专业英文术语大全
模具英语专业术语 模具述语 一、入水：gate 进入位：gate location 水口形式：gate type 大水口：edge gate 细水口：pin-point gate 水口大小：gate size 转水口：switching runner/gate 唧嘴口径：sprue diameter 二、流道: runner 热流道：hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形流道：round(full/half runner 流道电脑分析：mold flow analysis 流道平衡:runner balance 热嘴：hot sprue 热流道板：hot manifold 发热管：cartridge heater 探针: thermocouples 插头：connector plug 插座：connector socket 密封/封料：seal 三、运水：water line 喉塞：line lpug 喉管：tube 塑胶管：plastic tube 快速接头：jiffy quick connector plug/socker 四、模具零件：mold components 三板模：3-plate mold 二板模：2-plate mold 边钉/导边：leader pin/guide pin 边司/导套：bushing/guide bushing 中托司：shoulder guide bushing 中托边L：guide pin 顶针板：ejector retainner plate 托板：support plate 螺丝：screw 管钉：dowel pin 开模槽：ply bar scot 内模管位：core/cavity inter-lock 顶针：ejector pin 司筒：ejector sleeve 司筒针：ejector pin 推板：stripper plate 缩呵：movable core,return core core puller 扣机（尼龙拉勾）：nylon latch lock 斜顶：lifter 模胚（架）：mold base 上内模：cavity insert 下内模：core insert 行位（滑块）：slide 镶件：insert 压座/斜鸡：wedge 耐磨板/油板：wedge wear plate 压条：plate 撑头: support pillar 唧嘴：sprue bushing 挡板：stop plate 定位圈：locating ring 锁扣：latch 扣鸡：parting lock set 推杆：push bar 栓打螺丝：S.H.S.B 顶板：eracuretun 活动臂：lever arm 分流锥：spure sperader 水口司:bush 垃圾钉：stop pin 隔片：buffle 弹弓柱：spring rod 弹弓:die spring 中托司：ejector guide bush 中托边：ejector guide pin 镶针：pin 销子：dowel pin 波子弹弓：ball catch 喉塞: pipe plug 锁模块：lock plate 斜顶：angle from pin
模具常用英文词汇
钣金设计中常用的其它术语 扩孔enlarge hole 自铆self-chinching 全周压毛边all round burr 平头拉钉set-head rivet 表面处理finish 定位销dowel pin 挂钩hook 平头铆钉closed-end rivet 焊接线weld line 塑料固定栓fastener, plastic, push-type 压合胶粘剂pressure sensitive adhesive 尼龙绑带tie wrap, nylon 五金件hardware 泡棉静电导片gasket, foam, emi 贴纸labeling 铍铜静电导片gasket, beck, emi 烤漆paint 圆头螺钉button-head screw 电镀plating 平头螺母nut flush 铭板nameplate 平齐自铆flush, self-clinching 包装packing 紧固螺丝fix screw 铁材零件sheet metal parts 组装assembly 塑料零件plastic parts 凹陷,顶针sink mark 压边铆钉open-end rivet 插孔jack 弹簧螺丝caps 度thick 文字,记号char actor 半冲孔spring slice 角corner 基座chassis 自锁螺母nut self-clenching 承座bracket 轴肘式铆接toggle lock 承架horsing 卡尺caliper 下盖base 打印字模stamp letter 去毛边deburr 推板导住ejector guide 直导套guide bush, straight[straight bushing] 带头导套guide bush, straight {shoulder bushing} 推板导套ejector guide bush[ejector bushing] 定位圈Locating ring 锥形定位件mould bases locating elements 复位杆ejector plate return pin[push-back pin] 限位钉stop pin[stop but ton] 限位块stop block [stop pad] 定距拉杆puller[length]bolt 定距拉板puller[limit]plate 成形推杆forming ejector pin 圆柱头推杆ejector pin with cylindrical head 带肩推杆shouldered ejector pin 扁推杆flat ejector pin 推管ejector sleeve 推块ejector pad 推件板stripper plate 推杆固定板ejector retainer plate ; 推板ejection plate[elector plate] 连接推杆ejector tie rod 冲裁间隙blanking clearance 模具闭合高度die shut height 压力机闭合高度shut height Of press machine 冲模寿命die life 压力中心center Of load 冲模中心center Of die 冲压方向pressing direction 送料方向feed direction 排样blank layout 搭边scrap 进距feed pitch 切边余量trimming allowance 毛刺burr 冲裁力blanking force 弯曲力bending force 拉仲力drawing force 挤压力extruding force 卸料力stripping force 推件力ejecting force 顶件力kicking force 压料力pressure plate force 压边力black holder force 毛坯blank ;
机械用语的英语翻译
机械用语的英语翻译 恒温·干燥器/恒温恒湿器 Drying Ovens/Humidity Chambers 送风定温恒温器 Forced Convection Constant Temperature Ovens 惰性气体恒温器 Inert Gas Ovens 精密恒温器 Precision Constant Temperature Ovens 洁净恒温器 Clean Ovens 送风定温干燥器 Forced Convection Constant Temperature Drying Ovens 空气幕送风定温恒温器 Forced Convection Ovens With Air Curtain 定温干燥箱 Constant Temperature Drying Ovens 角形真空定温干燥器 Vacuum Drying Ovens 恒温恒湿器 Constant Temperature and Humidity Chambers 流水线设备 In-Line System for Underfill Adhesive and Encapsulation 恒温培养器 Constant Temperature Incubators--- 可程式低温培养器 Low Temperature Program Type Incubators 低温培养器 Low Temperature Incubators 低温稳定性培养器 Low Temperature Stability Incubators 培养器 Incubators CO2培养器 CO2 Incubators
振荡培养器 Shaking Incubators 冻结干燥器 Freeze Dryers--- 冻结干燥器 Freeze Dryers 离心形冻结干燥器 Centrifugal Freeze Dryers 灭菌器 Sterilizers--- 干热灭菌器 Drying Sterilizers 高压灭菌器 Autoclaves Sterilizers 低温等离子灭菌器 Low Temperature Plasma Sterilizers 环形燃烧管灭菌器 Loop Cinerator 纯水制造装置 Water Purifiers--- 纯水制造装置 Water Stills 超纯水制造装置 Ultra-pure Water Purifiers 简易纯水制造装置 Water Purifiers 超纯水制造装置系统 Ultra-pure Water Purifier System 大容量纯水制造装置 Water Purifiers System 洗净器 Washers--- 实验室玻璃器皿清洗机 Laboratory Glassware Washers 超声波清洗机 Ultrasonic Cleaners 大型超声波清洗机 Aqueous Ultrasonic Cleaning Systems 超声波试管清洗机 Ultrasonic Pipet Washers 超声波清洗机 Ultrasonic Cleaners