(完整)电池行业英语词汇大全,推荐文档.doc
Alkaline batteries :碱性电池
Capacitor batteries :电容电池
Carbon zinc batteries :碳锌电池
Lead acid batteries :铅酸电池
Lead calcium batteries :铅钙电池
Lithium batteries :锂电池
Lithium ion batteries :锂离子电池
Lithium polymer batteries :锂聚合物电池
Nickel cadmium batteries :镍镉电池
Nickel iron batteries :镍铁电池
Nickel metal hydride batteries:金属氧化物镍氢电池/ 镍氢电池
Nickel zinc batteries :镍锌电池
Primary batteries :原电池
Rechargeable batteries :充电电池
Sealed lead acid batteries :密封铅酸电池
Silver cadmium batteries :银钙电池
Silver oxide batteries :银氧化物电池
Silver zinc batteries :银锌电池
Zinc chloride batteries :银氯化物电池
Zinc air batteries :锌空电池
Environmental Protection batteries: 环保电池
Lithium batteries :锂电池
Lithium ion batteries :锂离子电池
Lithium polymer batteries :锂聚合物电池
铅酸蓄电池 Lead-acid battery
起动铅酸电池 Lead-acid starter batteries
摩托车用铅酸电池 Lead-acid batteries for motorcycles
内燃机车用铅酸电池 Lead-acid batteries for disel locomotive
电动道路车辆用铅酸电池Lead-acid batteries for electric road vehicles 小型阀控密封式铅酸电池small-sized valve-regulated lead-acid batteries 航空用铅酸电池 Aircraft lead-acid batteries
固定型阀控密封式铅酸蓄电池Lead-acid batteries for stationary valve- regulated 铅酸电池用极板plate for lead-acid battery
铅锭 lead ingots
牵引用铅酸电池Lead-acid traction batteies
电解液激活蓄电池electrolyte activated battery
vent valve排气阀
filling device for pleral cells电池组填充装置
negative electrode负电极
negative plate负极板
addition reagent for negative plate负极板添加剂
indicator指示器
top cover上盖
vent plug液孔塞
expanded grid扩展式板栅
specific gravity indicator比重指示器
electrolyte level control pipe电解液液面控制管
electrolyte level indicator电解液液面指示器
electrolyte level sensor电解液液面传感器
hard rubber container硬橡胶槽
envelope separator包状隔板
woven cloth tube纺布管
spongy lead海绵状铅
partition隔壁
over the partition type 越过隔壁型
through the partition type 贯通隔壁贯通型
separator 隔板
(1)battery rack(2)battery stand(3)battery stillage 蓄电池架 / 蓄电池底垫active material 活性物质
glass fiber separator 玻璃纤维隔板
glass mat 玻璃纤维绵
glass mat tube 玻璃纤维绵管
spacing washer 间隔垫圈
reinforced fiber separator 强化纤维隔板
polarity mark plate 极性标记板
pole 极柱
pole insulator 极柱绝缘子
pole nut 极柱螺母
plate 极板
plate foot 极板足
plate supporter 极板支撑件
element 极板群 / 极群组
pole bolt 极柱螺栓
plate lug 极板耳
dilute sulfuric acid 稀硫酸
steel can 金属罐
steel container 金属蓄电池槽
(1)madribs(2)element rest 鞍子 / 极群组座
tubular plate 管状极板
gelled electrolyte 胶体电解液
grid 板栅
caution label 警告标签
synthetic resin separator 合成树脂隔板
plastics container 塑料蓄电池槽
synthetic fiber separator 合成纤维隔板
connector sunken type 沉没型连接器
connetor exposed type 露出型连接器
safety valve test 安全阀测试
ampere-hour efficency 安时效率
one charge distance range 一次充电行程
gas recombination on negative electrode type 阴极气体再化合型 /阴极气体复合型 cut-off discharge 终止放电 /截止放电
(1 ) specific characteristic (2)energy density (1) 比特性( 2)能量密度recovering charge 恢复充电
(1)open circuit voltage(2)off-load voltage
开路电压/空载电压overcharge过充电
gassing 析气
overcharge life test 过充电寿命试验
accelerated life test 加速寿命试验
active material utilization 活性物质利用率
theoretical capacity of active material 活性物质的理论容量
over discharge 过放电
intermittent discharge 间歇放电
full charge 完全充电
full discharge 完全放电
reverse charge 反充电 /反向充电
quick charge 快速放电
allowable minimum voltage 允许最小电压
equalizing charge 均衡充电
creeping 蠕变
group voltage 组电压
shallow cycle endurance 轻负荷寿命 /轻负荷循环寿命
characteristic of electrolyte decrease 电解液减少特性
nominal voltage 标称电压
high rate discharge 高率放电
high rate discharge characteristic 高率放电特性
5 second voltage at discharge放电5秒电压
(1) cold cranking ampere ( 2) cold cranking performance
(1)冷启动电流( 2 )冷启动性能
cycle life test 循环寿命测试
maximum voltage at discharge 最大放电电压
30 second voltage at discharge 放电 30 秒电压
residual capacity 残存容量
(1)hour rate(2) discharge rate ( 1 )小时率( 2)放电率
(1) self discharge (2) local action ( 1 )自放电(2)局部自放电
(1) self discharge rate(2) local action rate ( 1)自放电率(2)局部自放电率 actual capacity 实际容量
(1)starting capability(2)cranking ability 启动能力
cranking current 启动电流
battery clamp test 电池夹钳测试
power density 功率密度
momentary discharge 瞬间放电
modified constant voltage charge 修正恒定电压充电
initial capacity 初始容量
gas recombination by catalyser type 触媒气体复合式initialcharge 初始充电
viberation test 振动试验
predetermined voltage 预定电压
total voltage 总电压
activation test for dry charged battery 干式荷电蓄电池活化试验salting 盐析
earthquake-proof characteristics 防震性能
dielectric voltage withstand test电介质耐压试验
short time discharge 短时间放电
escaped acid mist test 酸雾逸出测试
terminal voltage 端子电压
cell voltage 单电池电压
step charge 阶段充电
short-circuit current短路电流
storage test 保存测试
high rate discharge at low temperature 低温高率放电
rated voltage 额定电压
rated capacity 额定容量
fixed resistance discharge 定阻抗放电
constant voltage charge 恒压充电
constant voltage life test 恒压寿命测试
constant current charge 恒流充电
constant voltage constant current charge 恒流恒压充电constant current discharge 恒流放电
constant watt discharge 恒功率放电
low rate discharge characteristics 低率放电特征
trickle charge 涓流充电
trickle charge current 涓流充电电流
trickle charge life test 涓流充电寿命测试
thermal runaway 热失控
driving pattern test 运行测试
capacity in driving pattern test 运行测试
boost charge 急充电
floating charge 浮充电
floating charge voltage 浮充电电压
floating charge current 浮充电电流
(1)mean voltage (2)average voltage平均电压
on-load voltage 负载电压
discharge duration time 放电持续时间
(1)final voltage(2)cut-off voltage(3)end voltage 终止电压 / 截止电压 depth of discharge 放电深度
discharge voltage 放电电压
discharge current 放电电流
discharge current density 放电电流密度
discharge watt-hour 放电瓦时
discharge characteristics 放电特性
discharged ampere-hour 放电安时
explosion proof test 防爆测试
auxiliary charge 补充电
maintenance factor 维护率
storage characteristics 保存特性
gas recombinating efficiency 气体复合效率 / 气体再化合效率
charge 充电
charge acceptance test 充电可接受性试验
start-of-charge current 充电开始电流
charge efficiency 充电效率
end-of-charge voltage 充电结束电压
specific gravity of electrolyte at the end of charge 充电结束时电解液比
重 charge voltage 充电电压
charge current 充电电流
charged watt-hour 充电瓦时
charge characteristic 充电特性
charge ampere-hour 充电安时
deep cycle endurance 重负荷循环寿命/重复合寿命
weight engergy density 重量能量密度
rubber pad 橡胶垫
lower level line 下液面线
side terminal 侧端子
collective exhaust unit 公共的排放单元
sintered plaque 烧结极板
sintered separator 烧结隔板
sintered plate 烧结极板
catalyst plug 催化塞
spine 芯骨
strap 带
spacer 隔离物
insulating tube 绝缘管
intercell connector 连接线 /连接条
connector cover 连接管盖
float mounted plug 浮动安装的栓
(1)pasted plate (2)grid type plate涂膏式极板
braidd tube 编织管
(1)flame-arrester vent plug (2)flam-retardant vent plug 安全塞 explosion and splash proof construction 防爆防溅结构
baffle 保护板
pocket type plate 袋式极板
bottom hole-down 底孔向下(固定)
bolt fastening terminal 螺栓连接端子
male blade 阳片
monoblock container 整体槽
positive electrode 正极
positive plate 正极板
leading wire terminal 引线端子
retainer mat 止动垫片
ribbed separator 肋隔板
(1)jumping wire (2)inter low wire 跳线
end plate 端板
filling plug 注液塞
plante plate 形成式极板 /普朗特极板
tubular plate 管式极板
low electric resistance separator 低电阻隔板
tapered terminal post 锥形接线柱
electrolyte 电解液
container 蓄电池槽 /蓄电池壳
set of container 成套蓄电池槽
level-scope mounted plug透视塞/透视栓
handle 手柄
jug 取液管
(1)connector;(2)plug concent (1) 连接器; (2) 插座式连接器connector wire 连接线
connecting bar 连杆
connecting bar cover 连杆帽
lead 引线 /连接线
edge insulator 绝缘卡
side frame 侧框架
battery cubicle 蓄电池箱
perforated separator 多孔隔板
burning rod ( 铅)焊条
terminal 端子
terminal connector 端子连接条
terminal cover 端子盖
terminal base 端子座
tab 接线片
lead bushing 铅套
corrugated separator 波形隔板
(1)lead dioxide;(2)lead peroxide (1) 二氧化铅;(2) 过氧化铅
(1)woven separator;(2)nonwoven separator (1) 织物隔板;(2) 非织物隔板vent hole通气孔
exhaust tube排气管
antipolar mass反极性物质
output cable输出电缆
microporous rubber separator微孔像胶隔板
specific gravity indicator比重计
leaf separator叶片式隔板
lid sealing compound密封剂/封口剂
sealing gasket密封衬垫/垫圈
lid 蓄电池盖
set of lid系列的盖
方通
盖板
cover board
底板
solepiece
钢珠
steel ball
压钢珠
press steel ball
防爆阀
valve preventing explosion
大电流 (倍率 )放电
discharge in highrate current
标称电压
Normal voltage
标称容量
normal capacity
放电容量
discharge capacity
充电上限电压
limited voltage in charge
放电下限电压
terminating voltage in discharge 恒流充电
constant current charge
恒压充电
constant voltage charge
恒流放电
constant current discharge
放电曲线
discharge curve
充电曲线
charge curve
放电平台
discharge voltage plateau
容量衰减
capacity attenuation
起始容量
initial discharge capacity
流水线
pipelining
传送带
carrying tape
焊极耳
welding the current collector
卷绕
wind
叠片
layer
贴胶带
stick tape
点焊
spot welding
超声焊
ultrasonic welding
The terminating voltage in discharge of the battery is 3.0 volt.The limited
voltage in charge of the battery is 4.2 volt.三元素
Nickle-Cobalt-Manganese Lithium Oxide
three elements materials
钴酸锂
Cobalt Lithium Oxide
锰酸锂
Manganese Lithium Oxide
石墨
graphite
烘箱
oven
真空烘箱
vacuum oven
搅拌机
mixing device
vacuum mixing device
涂布机
coating equipment
裁纸刀
分条机
equipment for cutting big piece to much pieces
辊压机roll press equipment
电阻点焊机
spot welding machine
超声点焊机
ultrasonic spot welding machine
卷绕机
winder
自动叠片机
auto laminating machine
激光焊机
laser welding machine
注液机
infusing machine
真空注液机
vacuum infusion machine
预充柜
pre-charge equipment
化成柜
formation systems
分容柜
grading systems
测试柜
testing systems
内阻仪
Battery inner resistance tester
万用表
Multimeter
转盘式真空封口机
Turntable type vacuum sealing machine
自动冲膜机
Automatic aluminum membrane shaper
序号首字母英文中文
1 A aging 老化
2 B battery charger 充电器
3 black-fleck 黑斑
4 C cap 盖板
5 capacity density 能量密度
6 capacity grading 分容
7 cathode tab welding极耳超焊
8cell电芯
9 charge(capacity) retention荷电(容量)保持
10 checking code检码
11 concave spot 凹点
12 constant current charge 恒流充电
13 constant current discharge 恒流放电
14 constant voltage charge 恒压充电
15 corrective measures 纠正措施
16 crack 裂纹
17 cut-off voltage 终止电压
18 cycle life 循环寿命
19 D dark trace 暗痕
20 degrade 降级
21 dent 凹痕
22 discharge depth 放电深度
23 distortion 变形
24 drape 打折
25 E Electrical and Mechanical Services Department 机电部 26 electrolyte 电解,电解液
27 empaistic 压纹
28 end-off voltage 放电截止电压
29 environmentally friendly 对环境友好
30 equipment first inspection 设备首检
31 erode 腐蚀
32 explosion-proof line 防爆线
33 F first inspection 首检
34 formation 化成
35 fracture 断裂
36 I inspection 检验
37 insulate 绝缘
38 internal resistance 内阻
39 J jellyroll 卷芯
40 joint 接缝,结合点
41 L laser deflecting 偏光
42laser reticle 激光刻线
43 laser welding-flatwise weld 激光焊接 -平焊
laser welding-standing weld 激光焊接 -立焊
44 leakage 漏液
45 leak-checking 测漏
46 leaving out of welding 漏焊
47 limited charge voltage 充电限制电压
48 local action 自放电
49 M margin turnly 翘边
50 measuring the dimension of cells电芯卡尺寸
51 meet requirement 达到要求
52 memory effects 记忆效应
53 N nick 划痕
54 nominal voltage 标称电压
55 notice-board confirmation 看板确认
56 nugget 硬块
57 O obverse 正面
58 open circuit voltage 开路电压
59 over charge 过充
60 over discharge 过放
61 over the thickness 超厚
62 P particle 颗粒
63 PE membrane PE 膜
64 pit 坑点
65 placing cells into the box 电芯装盒
66 point inspection 点检
67 preventive measures 预防措施
68 pricking the tapes 扎孔
69 process inspection 制程检验
70 put the battery piled up 将电芯叠放在一起
71 Q qualified products 合格品
72 quality assurance 质量保证
73 quality control 质量控制
74 quality improvement 质量改进
75 quality match 品质配对
76 quality planning 质量策划
77 R rated capacity 额定容量
78 recharge 再充电
79 refitting the can of cell 电芯壳口整形
80 requirement 要求
81 reverse 背面,反面
82 rework 返工
83ringing cells into pyrocondensation films 套热缩膜
84 S safety vent 安全阀
85 sand aperture 砂眼
86 scar 疤痕
87 secondary battery 二次电池
88 select appearance 选外观
sharp-set 批锋
89 short circuit checking 测短路
90 smudginess 污物
91 spot welding by laser 激光点焊
92 spot welding place 点焊位置
93 spraying the code 喷码
94 spur 毛刺
95 sticking the PVC cover boards 贴面垫
96 storing 陈化
97 storing with high voltage 高压储存
98 T tabs deflection 极耳歪斜
99 tabs excursion 极耳错位
100 technics requirement 工艺要求
101 U ultrasonic welding 超声波焊接
102 ultrasonic welding strength 超焊强度
103 unqualified products 不合格品
104 W wave 波浪
105 working procedure 工序
Voltage :
Units of measuring electrical current, all batteries are rated in volts DC.
(Direct Current). This determines how much energy is needed to power your equipment. Voltage plateau:(电压平台)
A slow decrease in voltage over a long period of time. As a rule, the plateau extends from the first voltage drop at the start of the discharge to the
bend of the curve after which the voltage drops rapidly at the end.
Nominal Voltage(标称电压)
The voltage of a battery, as specified by the manufacturer,
discharging at a specified rate and temperature.
The working voltage of a cell or battery begins at its electrical connections as soon as an electrical consumer is connected to it.
Discharging voltage, average voltage (放电电压)
The average discharging voltage is the average value of the discharging
voltage during the entire discharging process with a related discharging current. Open circuit voltage (OCV开路电压)
The voltage of a battery when there is no current flowing.
Closed-Circuit Voltage (CCV闭路电压)
The potential or voltage of a battery when it is discharging or charging.
State of charge:
The rate of charge capacity vs. whole capacity.
(起始电压)
A battery ' s initial voltage is the working voltage when discharging begins. End-point voltage (End voltage, Cutoff voltage, Final voltage)截止电压
Specified closed circuit voltage at which a service
output test is terminated. End-of-discharge voltage
The battery voltage when discharge is terminated.
End-of-charge voltage
The battery voltage when charge is terminated.
Cutoff voltage (V)
The battery voltage at which charge or discharge is terminated.
Definition: Capacity(容量)
The capacity of a cell is defined as how many mill-amp-hours (mAh) of
current the cell can store and subsequently deliver.
One mill-amp (mA) is 1/1000th of an Amp. Some larger cell
capacities are expressed in Amp-hours
(Ah).
“ Rated capacity is” varies with discharge rate, temperature, and cutoff voltage.
Rated capacity is different from power or energy
Example:
If a cell is rated at 1000 mAh, then it can deliver the following:
1000 mA of current for 1 hour
500 mA of current for 2 hours
200 mA of current for 5 hours
2000mA of current for 1/2 hour
Definition: Energy Density( 能量密度,包括体积比能量和质量比能量)
The energy density of a cell is a measure of how much energy can be
stored in the cell per unit volume or per unit weight.
E (watt-hours) = cell voltage x capacity rating
Energy density per unit volume is called the “ volumetric energy density ”and is expressed in terms of watt-hours/liter (wh/l).
Energy density per unit weight is called the “ gravimetric energy density ”and is expressed in terms of watt-hours/kilogram (wh/kg).
These measurements are useful when you are trying to determine which
cell has the most capacity per unit volume or weight.
1.Self Discharge 自放电
2.Uniformity of the Li-ion Batteries 锂离子电池的一致性
3.steel strap 钢带
4.Burst vent 防爆阀
5.Filling port 注液孔
6.spirally wound type cylindrical wound type 圆柱形
7.foil 箔
8.parallel-plate prismatic design 方形叠片式设计
Ageing (老化) -Permanent loss of capacity with frequent use or
The passage of time due to unwanted irreversible chemical reactions in
the cell. Anode (阳极) -The electrode in an electrochemical cell where oxidation takes place, releasing electrons.
During discharge the negative electrode of the cell is the anode.
During charge the situation reverses and the positive electrode of the cell is the anode.
Cathode(阴极)-The electrode in an electrochemical cell where reduction
takes place, gaining electrons.
During discharge the positive electrode of the cell is the cathode. During
charge the situation reverses and
The negative electrode of the cell is the cathode.
Cycle(循环)-A single charge and discharge of a battery.
Depth of discharge DOD (放电深度) -The ratio of the quantity of electricity overcharge removed from a cell on discharge to its rated capacity.
Internal impedance (交流内阻) -Resistance to the flow of AC current within a cell. It takes into account the capacitive effect of the plates forming
the electrodes. Internal resistance (直流内阻) -Resistance to the flow of DC
electric current within a cell,
the current drain from the cell.
A low internal impedance is usually required for a high rate cell.
锂离子电池的内阻英语概念到底用哪个概念,是Internal resistance还是Internal impedance,一些电池说明书内阻用Internal resistance,也有的用Internal impedance,我认为Internal impedance较好些,因为
国内测的电池内阻基本都是交流内阻,而外文也有这样定义的(我在别的帖子
也粘贴过):
Internal impedance(交流内阻)-Resistance to the flow of AC current within a cell. It takes into account the capacitive effect of the plates forming
the electrodes.Internal resistance(直流内阻)-Resistance to the flow of DC
electric current within a cell, causing a voltage drop across the cell in closed
circuit proportional to the current drain from the cell.
A low internal impedance is usually required for a high rate cell.
在 IEC6196002 中,只定义为 Internal resistance ,而用交流的方法测得
的内阻,叫 Internal a.c. resistance (交流内阻)
用直流的方法测得的内阻,叫Internal d.c. resistance (直流内阻),其实Internal a.c. resistance 测得就是阻抗,这样看来不如
用 Internal impedance (交流内阻)和Internal resistance (直流内阻)这两个概念把它们进行分清,以免混淆。
Alkaline batteries :碱性电池
Capacitor batteries :电容电池
Carbon zinc batteries :碳锌电池
Lead acid batteries :铅酸电池
Lead calcium batteries :铅钙电池
Lithium batteries :锂电池
Lithium ion batteries :锂离子电池
Lithium polymer batteries :锂聚合物电池
Nickel cadmium batteries :镍镉电池
Nickel iron batteries :镍铁电池
Nickel metal hydride batteries :金属氧化物镍氢电池/ 镍氢电池
Nickel zinc batteries :镍锌电池
Primary batteries :原电池
Rechargeable batteries :充电电池
Sealed lead acid batteries:密封铅酸电池
Silver cadmium batteries :银钙电池
Silver oxide batteries :银氧化物电池
Silver zinc batteries :银锌电池
Zinc chloride batteries :银氯化物电池
Zinc air batteries :锌空电池
Environmental Protection batteries: 环保电池
电子行业专业英语词汇
专用词汇表 一、生产流程 1.插机(刮蓝胶)component-inserting 2.装配assembly 3.修理repair 4.包装packaging 5.成品仓finishedgoodswarehouse 6.返工rework 7.啤胶件 8.组件成型componentmoulding 9.IC烧录ICprogram 10.插件insection 11.注塑plasticinjection 12.发料materialdelivery 13.插机 14.零件加工component-processing 15.炉前外观检查 visualinspectionbeforewavesolde ring 16.电源板波峰焊 powerboardwavesoldering 17.执锡 18.零件后焊handsoldering 19.零件焊接&打黄胶 20.低电压测试lowvoltagetest 21.半成品外观检查 Semi-finishedgoodsvisualinspecti on 22.过水洗机 23.打热熔胶dottinghotglue 24.装卡板 25.pallet栈板 26.IC烧录ICprogram 27.SMT(刮锡膏) 28.喷油sprayconformalcoating 29.焗干防水油 30.welding焊接 31.breathing排气 32.feed供料
33.Tiana天那水 34.toloadmaterial上料 35.tounloadmaterial卸料 36.toreturnmaterial/stockto退料 37.tofixadie装模 38.totakeapartadie拆模 39.coldforging冷锻 40.pressforging冲锻 41.toimposelines压线 42.tocompress,compressing压缩 43.焗炉温度 44.开槽groove 45.shearing剪断 46.接线端子terminal 47.tostake,staking,reviting铆合 48.fusetogether熔合 49.electricalsparkle电火花 50.fittogether组装在一起 51.fasten锁紧(螺丝) 52.rotatingspeed,revolution转速53.argonwelding氩焊 54.totakeapartadie卸下模具 55.toloadadie装上模具 56.totightabolt拧紧螺栓 57.tolooserabolt拧松螺栓 https://www.360docs.net/doc/be15054305.html,pounddie复合模 59.punchedhole冲孔 60.buffing抛光 61.chamferingmachine倒角机 62.panelboard镶块 63.tocutedges=sidecut=sidescrap切 边 64.topull,tostretch拉伸 65.Linestreching,linepulling线拉伸 66.engraving,toengrave刻印 67.degrease脱脂 68.rinse水洗 69.piercedie冲孔模 70.formingdie成型模 71.progressivedie连续模
电池专业术语英语汇总
Cell or Battery Related English Vocabulary prepared by Jackie, QQ:58805359 ID电池术语英文翻译备注1放电discharge 2极耳弯折tab bending 3解剖disassemble 4性能测试performance Testing 5倍率rate 6倍率放电discharge rate capabilities 7电流current 8电压voltage 9内阻impedance 10容量capacity 11循环寿命cycle Life 12半成品Semi-manufactured 13电池组pack 14电解液electrolyte 15废料flotsam 16负极片negative electrode 17钢芯pin 18极组jellyroll(J/R) 19铝箔aluminum foil 20冒盖cover board 21石墨graphite 22铜copper 23铜箔copper foil 24正极片positive electrode 25工艺科Technics Department 26机电科electromechanical Department 27品质科quality department 28生产科Production Department 29浆料桶slurry bucket 30碾压机compression rollers 31封口曲线crimping curve 32腐蚀erode 33供应商supplier 34控制方法control measures 35室温room temperature 36注释comments
模具专业英文术语大全
模具英语专业术语 模具述语 一、入水:gate 进入位: gate location 水口形式:gate type 大水口:edge gate 细水口: pin-point gate 水口大小:gate size 转水口: switching runner/gate 唧嘴口径: sprue diameter 二、流道: runner 热流道: hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形流道:round(full/half runner 流道电脑分析:mold flow analysis 流道平衡:runner balance 热嘴: hot sprue 热流道板:hot manifold 发热管:cartridge heater 探针: thermocouples 插头: connector plug 插座: connector socket 密封/封料: seal 三、运水:water line 喉塞:line lpug 喉管:tube 塑胶管:plastic tube 快速接头:jiffy quick connector plug/socker 四、模具零件: mold components 三板模:3-plate mold 二板模:2-plate mold 边钉/导边:leader pin/guide pin 边司/导套:bushing/guide bushing 中托司:shoulder guide bushing 中托边L:guide pin 顶针板:ejector retainner plate 托板: support plate 螺丝: screw 管钉:dowel pin 开模槽:ply bar scot 内模管位:core/cavity inter-lock 顶针: ejector pin 司筒:ejector sleeve 司筒针:ejector pin 推板:stripper plate 缩呵:movable core,return core core puller 扣机(尼龙拉勾):nylon latch lock 斜顶:lifter 模胚(架): mold base 上内模:cavity insert 下内模:core insert 行位(滑块): slide 镶件:insert 压座/斜鸡:wedge 耐磨板/油板:wedge wear plate 压条:plate 撑头: support pillar 唧嘴: sprue bushing 挡板:stop plate 定位圈:locating ring 锁扣:latch 扣鸡:parting lock set 推杆:push bar 栓打螺丝:S.H.S.B 顶板:eracuretun 活动臂:lever arm 分流锥:spure sperader 水口司:bush 垃圾钉:stop pin 隔片:buffle 弹弓柱:spring rod 弹弓:die spring 中托司:ejector guide bush 中托边:ejector guide pin 镶针:pin 销子:dowel pin 波子弹弓:ball catch 喉塞: pipe plug
电子电气类专业英语单词汇总
课一A Communications 通讯 1. equation n.相等, 平衡, 综合体, 2. communication n. 通信, 通讯, 交通communicate v.沟通, 通信, 3. triode n.三极管 4. storage n. 存储 5.transmission n. 传输, 传送, transmit v. 传输, 转送, 传达, 传导 6. amplifier n.放大器,扩音器 amplify v. 扩大,放大,增强amplification n. 扩大,放大 7. oscillator n.振荡器 8. correlate v. 是相互关联 correlation n.相互关系, 相关(性) 9. transmitter n.发射机 transmit receive transmission reception (发射) (接收) 10.subsequent adj.随后的 课一B Capacitors 电容 1.capacitor n. 电容器 2.capacitance n. 电容量(值) Resistor resistance capacitor capacitance inductor inductance 3. fixed adj. 固定的 variable adj. 可变的 4. dielectric n. 电介质,绝缘材料 adj. 绝缘的 5. relatively adv. 相对地 absolutely adv.绝对地 6. maximum adj. 最大的 n. 最大值 minimum adj. 最小的 n. 最小值 7. farad n. 法(拉) F ohm n. 欧姆Ω Henry n. 亨(利)H 8. trimmer n. 调整者, 整理者, 9. screwdriver n. 螺丝起子,改锥课二A Radio T ransmitter无线电发射机 1. radio transmitter 无线电发射机 radio n. 无线电,无线 2. telecommunication n.电信,电信学, 无线电通信 telephone n.电话,电话机 telegraph n.电报, 电报机, 电讯报 3. transmit v. 传输, 转送, 传达, 传导, 发射, 发报 transmit receive transmission reception transmitter receiv er (发射) (接收) 4. intelligence n.信息、情报、智能 information/message n.信息 5. potential adj.潜在的, 可能的, 势 的, n.潜能, 潜力, 电位 6. generate v.产生,发生 generation n.产生, 发生, 一代,7. frequency n.频 low frequency 几个Hz到几十kHz high frequency 几个MHz到几十 MHz radio frequency 几百MHz到几 个GHz 8. pulse signal 脉冲信号 9. wavelength n.波长用λ表示 10. output n.输出,产量 input n.输入 11. band n. 带,波段,频带 课二B Electromotive Force 电动势 1. electromotive adj.电动的,电动 势的 electromotive force 电动势 2.driving adj.驱动的 driving force n. 驱动力 driving unit 传动装置 3. volt n. 伏特 4. distinguish v.区分 5. potential difference 电位差 课三A Time Constant 时常数 1.nuclear adj.原子能的, n.核武器, 有核国 nuclear arms 核武 nuclear energy 核能 2.constant n.常数 adj.不断, 不断的, time constant 时间常数 3. instantaneously adv.瞬间地,即刻 instant n.瞬息, 一会儿, 时刻 4. dependent adj. 依赖的,依赖于,取决于 5. capacitiv e adj.电容的,容性的 capacitor n.电容器 capacitance n.电容值 6.discharge n.放电v.放电 charge n.电荷,充电v.充电 7.universal 普遍的, 全体的, 通用的, 课三B RL Time Constant RL时序常数 1.inductor n.电感器 inductance n.电感值(量) inductive adj.感应的; 电感的 2. function n.功能, 函数,作用, 3. Decay n.衰减v. 衰减 decay constant 衰减常数 decay factor 衰减因子 4. reverse adj.反向的, 相反, 逆转的 5. peak value 峰值
模具专业英语词汇大全
模具专业英语词汇 A abrasion n. 磨损 abrasion resistance n. 耐磨损性 abrasive n. 磨料 accelerator n. 促进剂 accuracy n. 准确性 accurate die casting 精密压铸 air trap 积风 acrylic n. 丙烯酸 /压克力 ì active plate 活动板 additive n. 添加剂 adhere v. 黏附 adhesion n. 黏合 adhesive n. 胶粘剂 air-cushion eject-rod 气垫顶杆 air cushion plate 气垫板 air entrapment n. 困气 anneal v. 退火 assemble v. 总成 B back pressure 背压 bismuth mold 铋铸模 baffle plate 挡块 barrel n. 机筒 /料筒 / bending block 折刀 bottom block 下垫脚 bottom plate 下托板(底板) bushing bolck 衬套 barrel temperature 料筒温度 blush 发 blank through dies 漏件式落料模 burnishi blow molding n. 吹塑成型 blow molding machine n. 吹塑机 brittle adj. 脆性 bubble n. 气泡 burr 毛刺 button d by-product n. 副产品 C calendering n. 压延 carbon steel n. 碳素钢 casting n. 铸造 catalyst n. 催化剂 cavity n. 型腔 chemical resistance n. 耐化学腐蚀性 chip v. 削 /凿
电子行业专业英语词汇
电子行业专业英语词汇 Document serial number【NL89WT-NY98YT-NC8CB-NNUUT-NUT108】
专用词汇表 一、生产流程 1.插机(刮蓝胶)component-inserting 2.装配assembly 3.修理repair 4.包装packaging 5.成品仓finishedgoodswarehouse 6.返工rework 7.啤胶件 8.组件成型componentmoulding 9.IC烧录ICprogram 10.插件insection 11.注塑plasticinjection 12.发料materialdelivery 13.插机 14.零件加工component-processing 15.炉前外观检查 visualinspectionbeforewavesolderi ng 16.电源板波峰焊 powerboardwavesoldering 17.执锡 18.零件后焊handsoldering 19.零件焊接&打黄胶 20.低电压测试lowvoltagetest 21.半成品外观检查Semi- finishedgoodsvisualinspection 22.过水洗机 23.打热熔胶dottinghotglue 24.装卡板 25.pallet栈板 26.IC烧录ICprogram 27.SMT(刮锡膏) 28.喷油sprayconformalcoating 29.焗干防水油 30.welding焊接 31.breathing排气32.feed供料 33.Tiana天那水 34.toloadmaterial上料 35.tounloadmaterial卸料 36.toreturnmaterial/stockto退料 37.tofixadie装模 38.totakeapartadie拆模 39.coldforging冷锻 40.pressforging冲锻 41.toimposelines压线 42.tocompress,compressing压缩 43.焗炉温度 44.开槽groove 45.shearing剪断 46.接线端子terminal 47.tostake,staking,reviting铆合 48.fusetogether熔合 49.electricalsparkle电火花 50.fittogether组装在一起 51.fasten锁紧(螺丝) 52.rotatingspeed,revolution转速 53.argonwelding氩焊 54.totakeapartadie卸下 55.toloadadie装上 56.totightabolt拧紧螺栓 57.tolooserabolt拧松螺栓 https://www.360docs.net/doc/be15054305.html,pounddie复合模 59.punchedhole冲孔 60.buffing抛光 61.chamferingmachine倒角机 62.panelboard镶块 63.tocutedges=sidecut=sidescrap切边 64.topull,tostretch拉伸 65.Linestreching,linepulling线拉伸 66.engraving,toengrave刻印 67.degrease脱脂 68.rinse水洗 69.piercedie冲孔模 70.formingdie成型模
电气工程专业英语词汇汇总(综合版)
电气工程师专业英语词汇汇总 10kV distribution substation 10kV配电所abrupt change of voltage 电压突变accumulation of electric energy 电能存储actuating coil 动作线圈adjustment diagram 调整图 alarm 报警 alarm signal 报警信号alternating light 变光灯 ammeter 电流表 apparent energy consumption unit 单位视在能耗 arc furnace 电弧炉 armature 电枢 arrester; lighting arrester; surge diverters 避雷器 automatic voltage regulator 电压自动调整器backlighting; background illumination 背景照明 battery box 电池箱 battery charger 电池充电器battery contactor 电池接触器battery fuse 电池保险丝battery resistor 电池电阻器 blow-out coil 磁吹线圈 boom 吊杆 bracket (OCS) 底座(接触网); 支架;托架bracket for headspan wire 定位索底座bridge 电桥 brush 电刷 built-in wardrobe; built-in closet; closet 壁灯 bulb; light(lamp) bulb; electric bulb 灯泡 butterfly valve with electric actuator 电动蝶阀 button 电钮 cable and accessories 电缆及附件 cable armour 电缆铠装 cable bays 电缆电线间隔cable box 电缆箱 cable bracket; cable tray 电缆托架 cable continuity test 电路复测 cable differential protection 电缆差动保护
模具专业英语词汇
入水:gate 进入位:gate location 水口形式:gate type 大水口:edge gate 细水口: pin-point gate 水口大小:gate size 转水口:switching runner/gate 唧嘴口径:spray diameter 流道: runner 热流道:hot runner, hot manifold 热嘴冷流道: hot spray/cold runner 唧嘴直流: direct spray gate 圆形流道:round(full/half runner 流道电脑分析:mold flow analysis 流道平衡:runner balance 热嘴:hot spray 热流道板:hot manifold 发热管:cartridge heater 探针: thermocouples 插头:connector plug 插座: connector socket 密封/封料: seal 运水:water line 喉塞:line plug 喉管:tube 塑胶管:plastic tube 快速接头:jiffy quick connector plug 模具零件:mold components 三板模:3-plate mold 二板模:2-plate mold 边钉/导边:leader pin/guide pin 边司/导套:bushing/guide bushing 中托司:shoulder guide bushing 中托边L:guide pin 顶针板:ejector retainner plate 托板:support plate 螺丝: screw 管钉:dowel pin 开模槽:ply bar slot 内模管位:core/cavity inter-lock 顶针:ejector pin 司筒:ejector sleeve 司筒针:ejector pin 模具专业英语 推板:stripper plate 缩呵:movable core, return core puller 扣机(尼龙拉勾):nylon latch lock 斜顶:lifter 模胚(架): mold base 上内模:cavity insert 下内模:core insert 行位(滑块): slide 镶件:insert 压座/斜楔:wedge 耐磨板/油板:wedge wear plate 压条:plate 撑头: support pillar 唧嘴: sprue bushing 挡板:stop plate 定位圈:locating ring 锁扣:latch 扣鸡:parting lock set 推杆:push bar 栓打螺丝:S.H.S.B injection nozzle 射出喷嘴 顶板:eracuretun 活动臂:lever arm 分流锥:spure sperader 水口司:bush 垃圾钉:stop pin 隔片:buffle 弹弓柱:spring rod 弹弓:die spring 中托司:ejector guide bush 中托边:ejector guide pin 镶针:pin 销子:dowel pin 波子弹弓:ball catch 喉塞: pipe plug 锁模块:lock plate 斜顶:angle from pin 斜顶杆:angle ejector rod 尼龙拉勾:parting locks 活动臂:lever arm 复位键、提前回杆:early return bar 气阀:valves 斜导边:angle pin
太阳能电池行业英语词汇1..
A A, Ampere的缩写, 安培 a-Si:H, amorph silicon的缩写, 含氢的, 非结晶性硅. Absorption, 吸收. Absorption of the photons:光吸收;当能量大于禁带宽度的光子入射时,太阳电池内的电子能量从价带迁到导带,产生电子——空穴对的作用,称为光吸收。 Absorptionscoefficient, 吸收系数, 吸收强度. AC, 交流电. Ah, 安培小时. Acceptor, 接收者, 在半导体中可以接收一个电子.
Alternating current, 交流电,简称“交流. 一般指大小和方向随时间作周期性变化 的电压或电流. 它的最基本的形式是正弦电流. 我国交流电供电的标准频率规定为50赫 兹。交流电随时间变化的形式可以是多种多样的。不同变化形式的交流电其应用范围和产生 的效果也是不同的。以正弦交流电应用最为广泛,且其他非正弦交流电一般都可以经过数 学处理后,化成为正弦交流电的迭加。 AM, air mass的缩写, 空气质量.直射阳光光束透过大气层所通过的路程,以直射太 阳光束从天顶到达海平面所通过的路程的倍数来表示。当大气压力P=1.013巴,天空无云时,海平面处的大气质量为1。 amorphous silicon solar cell:非晶硅太阳电池(a—si太阳电池)用非晶硅材料及其合金制造的太阳电池称为非晶硅太阳电池,亦称无定形硅太阳电池,简称a—si太阳电池。Angle of inclination, 倾斜角,即电池板和水平方向的夹角,0-90度之间。
Anode, 阳极, 正极. B Back Surface Field, 缩写BSF, 在晶体太阳能电池板背部附加的电子层, 来提高电流值. Bandbreak, 在半导体中, 价带和导带之间的空隙,对于半导体的吸收特性有重要意义. Becquerel, Alexandre-Edmond, 法国物理学家, 在1839年发现了电池板效应. BSF, back surface field的缩写. Bypas-Diode, 与太阳能电池并联的二极管, 当一个太阳能电池被挡住, 其他太阳能电池产生的电流可以从它处通过.
电子通信专业英语词汇
A a bit 一个比特a coil of 一圈 a mix of comflicting information 一个混合的相互冲突的信号 a parallel or series circuit 并联成串联回路 abbreviate 缩写abruptly 突然地absolutely summable 完全可求和 absolute绝对 AC 交流accomplish 实现 accumulate 聚集accurately 精确的 acoustic声学acronym 缩写across the open connection point 开路电压actirated simultaneously 同时被激励activation 激励 activation 激活active devices有源器件 active 有源additional term附加项 adequate 适当地adjacent 相邻的adjustable可调的aeronautics 太空学aeronautics and astronautics 航空航天 aircraft飞行器 alarm 警报器 algebra 代数 algorithm 算法 all or nothing 宁为玉碎,不 为瓦全 allow the solution 求解 alter 转换 alternate current 交流 alternatively 或 者 altitude 海拔 amount 量 ampere 安培 amplification factor 放大系数 amplify放大 amplitude 振幅 an electric combination lock 电子号码锁 an exact relation 直接关系 an initial time 初始 analog ics 模 拟集成电路 analog 模拟 analogous fashion 类似的方式中 analogous 相似的 analog类似的 analytic and numerical solution 解析法和数值法求 解过程 anatomical 解 剖,人体解剖学 angle 角度 anisotropic 各 向异性的 annual 年 antenna天线 apparatus仪器 appliance 工具,设 备,装置,仪表 appointed任命 apprenticed学徒 approach进场 appropriate 适合 approuch 接近地面 approximate近似 arbitrary 任意 are also governed 符合 arise 出现,产 生 arithmetic operations 算 法操作 arithmetic 算术 armed force 军 事力量 artery动脉 artificially 人为 地 assemble 组合 associated with 伴随着 Associative Law 结合律 associative 结合 (率) assume假设 astatic needle 无定向磁针 astatic不定向的 astronautics 太 空航空学 astronomically 天 文学的 astronomy天文学 atmospheric 大气 atom 原子 atomic原子 attenuation衰减 audio音频 automotive vehicle 汽车 available to motivate 可用于驱 动 axial轴 B bachelor 学士 back-of-the-envel ope type analysis 黑箱类型的封 装中 back-of-the-envel ope 粗略 bandwidth带宽 bar 横杠 base 基极 basic operatiom 操作 battery 电池 be analogous to 与…相似 be appropriate for 适合 be conservative 保留 be converted into 转换成 be demited as命名 的为 be evaluated被赋 值/被评估 be expanded被扩展 be factored into 被给予系数 be indicated表示 be isotropic各个 同性的 be present in存在 be reduced to归纳 be referred to in terms of flow 被 比喻做流动的形态 be released 放 开 be subject to易遭 受… be supplemented by 被增加 be symbolically denoted with 用…符号表示 beam(光)束 behavior 性能 beta β bias 偏见 binary digit 二 进制数字 binary 二进制 biological 生物学 biomedical engineering生物医 学工程 bipolar transistor 双极管 bipolar 双极型 blacksmith铁匠 block 阻塞 Boltzman波尔兹曼 bookbinder 装 订商 Boolean algebra 布尔代数 Boolean 布尔 bound 跳跃 boundary condition 边界条件 bounded 有界的 bounding surface 边界局面 brackets 方括号 brightness亮度 broadcast广播 building block结 构单元 but rather to 而是 buzzer 蜂鸣器 by a vector 以 矢量方式
电子行业英语
A Analog 模拟 A/D Analog to Digital 模-数转换 AAC Advanced Audio Coding 高级音频编码 ABB Automatic Black Balance 自动黑平衡 ABC American Broadcasting Company 美国广播公司 Automatic Bass Compensation 自动低音补偿 Automatic Brightness Control 自动亮度控制 ABL Automatic Black Level 自动黑电平 ABLC Automatic Brightness Limiter Circuit 自动亮度限制电路 ABU Asian Broadcasting Union 亚洲广播联盟(亚广联 ABS American Bureau of Standard 美国标准局 AC Access Conditions 接入条件 Audio Center 音频中心 ACA Adjacent Channel Attenuation 邻频道衰减 ACC Automatic Centering Control 自动中心控制 Automatic Chroma Control 自动色度(增益控制 ACK Automatic Chroma Killer 自动消色器 ACP Additive Colour Process 加色法 ACS Access Control System 接入控制系统 Advanced Communication Service 高级通信业务 Area Communication System 区域通信系统 ADC Analog to Digital Converter 模-数转换器 Automatic Degaussirng Circuit 自动消磁电路 ADL Acoustic Delay Line 声延迟线 ADS Audio Distribution System 音频分配系统 AE Audio Erasing 音频(声音擦除 AEF Automatic Editing Function 自动编辑功能 AES Audio Engineering Society 音频工程协会 AF Audio Frequency 音频 AFA Audio Frequency Amplifier 音频放大器 AFC Automatic Frequency Coder 音频编码器 Automatic Frequency Control 自动频率控制 AFT Automatic Fine Tuning 自动微调 Automatic Frequency Track 自动频率跟踪 Automatic Frequency Trim 自动额率微调 AGC Automatic Gain Control 自动增益控制 AI Artificial Intelligence 人工智能 ALM Audio-Level Meter 音频电平表 AM Amplitude Modulation 调幅 AMS Automatic Music Sensor 自动音乐传感装置 ANC Automatic Noise Canceller 自动噪声消除器
模具专业的英语词汇大全
模具专业的英语词汇大全 一、模具专业英语 入水:gate 进入位:gate location 水口形式:gate type 大水口:edge gate 细水口: pin-point gate 水口大小:gate size 转水口:switching runner/gate 唧嘴口径:sprue diameter 二、流道: runner 热流道:hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形流道:round(full/half runner 流道电脑分析:mold flow analysis 流道平衡:runner balance 热嘴:hot sprue 热流道板:hot manifold 发热管:cartridge heater 探针: thermocouples 插头:connector plug 插座: connector socket 密封/封料: seal 三、运水:water line 喉塞:line lpug 喉管:tube 塑胶管:plastic tube 快速接头:jiffy quick connector plug/socker 四、模具零件:mold components 三板模:3-plate mold 二板模:2-plate mold 边钉/导边:leader pin/guide pin 边司/导套:bushing/guide bushing 中托司:shoulder guide bushing 中托边L:guide pin 顶针板:ejector retainner plate 托板:support plate 螺丝: screw 管钉:dowel pin 开模槽:ply bar scot 内模管位:core/cavity inter-lock
电子行业专业英语词汇
电子行业专业英语词汇 Document number:WTWYT-WYWY-BTGTT-YTTYU-2018GT
专用词汇表 一、生产流程 1. 插机(刮蓝胶)component- inserting 2. 装配 assembly 3. 修理repair 4. 包装 packaging 5. 成品仓 finished goods warehouse 6. 返工 rework 7. 啤胶件 8. 组件成型 component moulding 9. IC 烧录 IC program 10. 插件 insection 11. 注塑 plastic injection 12. 发料 material delivery 13. 插机 14. 零件加工 component-processing 15. 炉前外观检查 visual inspection before wave soldering 16. 电源板波峰焊 power board wave soldering 17. 执锡 18. 零件后焊 hand soldering 19. 零件焊接&打黄胶 20. 低电压测试 low voltage test 21. 半成品外观检查Semi-finished goods visual inspection 22. 过水洗机 23. 打热熔胶 dotting hot glue 24. 装卡板 25. pallet 栈板 26. IC 烧录 IC program 27. SMT(刮锡膏) 28. 喷油 spray conformal coating 29. 焗干防水油 30. welding 焊接 31. breathing 排气 32. feed 供料 33. Tiana 天那水
电池英语及翻译 专业术语
Alkaline batteries :碱性电池 Capacitor batteries:电容电池 Carbon zinc batteries :碳锌电池 Lead acid batteries:铅酸电池 Lead calcium batteries:铅钙电池 Lithium batteries :锂电池 Lithium ion batteries :锂离子电池 Lithium polymer batteries:锂聚合物电池 Nickel cadmium batteries :镍镉电池Nickel iron batteries :镍铁电池 Nickel metal hydride batteries :金属氧化物镍氢电池/镍氢电池 Nickel zinc batteries:镍锌电池 Primary batteries :原电池 Rechargeable batteries :充电电池Sealed lead acid batteries:密封铅酸电池 Silver cadmium batteries :银钙电池 Silver oxide batteries :银氧化物电池 Silver zinc batteries:银锌电池 Zinc chloride batteries:银氯化物电池 Zinc air batteries:锌空电池 Environmental Protection batteries:环保电池 Lithium batteries :锂电池 Lithium ion batteries :锂离子电池 Lithium polymer batteries:锂聚合物电池 铅酸蓄电池 Lead-acid battery 起动铅酸电池 Lead-acid starter batteries 摩托车用铅酸电池 Lead-acid batteries for motorcycles 内燃机车用铅酸电池 Lead-acid batteries for disel locomotive 电动道路车辆用铅酸电池 Lead-acid batteries for electric road vehicles 小型阀控密封式铅酸电池 small-sized valve-regulated lead-acid batteries 航空用铅酸电池 Aircraft lead-acid batteries固定型阀控密封式铅酸蓄电池 Lead-acid batteries for stationary valve-regulated 铅酸电池用极板 plate for lead-acid battery 铅锭 lead ingots 牵引用铅酸电池 Lead-acid traction batteies 电解液激活蓄电池electrolyte activated battery更多电池资讯:https://www.360docs.net/doc/be15054305.html,/ 电池产品认证指导网站: https://www.360docs.net/doc/be15054305.html,/ekeyword.php?ekeyid=6vent valve 排气阀 filling device for pleral cells 电池组填充装置 negative electrode 负电极 negative plate 负极板addition reagent for negative plate 负极板添加剂 indicator 指示器 top cover 上盖 vent plug 液孔塞 expanded grid 扩展式板栅