linux配置网络打印机

动检测并安装即插即用打印机”

b）、选择“创建新端口”端口类型选“Standard TCP/IP Port”

c）、打印机名或IP地址填上述Linux主机的IP地址

d）、选“自定义”，点“设置”按钮，确认“协议”为Raw，“端口号”为9100

e）、安装打印驱动程序，厂商选“HP”，打印机选“HP LaserJet P2015Series PCL 6”

f）、确认将新添加的打印机设置为默认打印机

虽然是台破PC，但单纯用做打印服务器也实在是太浪费资源了，再配置一下samba，把剩余的磁盘空间用做部门内的共享服务器，报废的计算机又可以继续发挥余热啦。

设备：水星MW4530R8M无线路由器，惠普HP MFP M1005打印一体机。

固件：?OpenWrt Barrier Breaker14.07r44382by Haxc；惠普HP MFP M1005打印一体机打印机固件采用hplj固件

https://www.360docs.net/doc/0b16290217.html,/hplj/。

?下面是安装设置教程：

****************part I路由器端安装设置***************?

?1、路由器端安装打印机服务器

通过putty软件SSH登陆到路由器安装，如果你安装了上述的openwrt 固件，可略过此步骤，里面已经集成了。

?opkg update

opkg install kmod-usb-printer usbutils p910nd luci-app-p910nd

2.安装打印机固件

HP的低端打印机自身不带打印固件，每次连接pc时?固件会从pc加载到打印机中。博主的HP MFP M1005就属于这种。通过putty软件SSH 登陆

?cd/usr/lib/

wget https://www.360docs.net/doc/0b16290217.html,/hplj/sihp1005.dl

?每次打印机上电要自动加载这个驱动固件：

?打开编辑器：vi/etc/hotplug.d/usb/20-printer

输入：

#############################################?

#!/bin/sh

#change this to the location where you put the.dl file:

FIRMWARE=/usr/lib/sihp1005.dl

DEVICE=/dev/usb/lp0

LOGFILE=/var/log/printer

if["$PRODUCT"="3f0/3b17/100"-a"$ACTION"="add"-a "$DEVTYPE"="usb_interface"];then

echo"$(date):STARTING">$LOGFILE

for i in$(seq30);do

echo"$(date):Attempt number$i on$DEVICE">> $LOGFILE

if[-c$DEVICE];then

echo"$(date):Device$DEVICE found.">>$LOGFILE

if[-z"'usb_printerid$DEVICE|grep FWVER"]; then

echo"$(date):No firmware found on $DEVICE">>$LOGFILE

echo"$(date):Sending firmware to printer...">>$LOGFILE

cat$FIRMWARE>$DEVICE

echo"$(date):done.">>$LOGFILE

else

echo"$(date):Firmware already there on $DEVICE">>$LOGFILE

fi

echo"$(date):EXITING">>$LOGFILE

exit

fi

sleep1

done

fi

?#############################

??其中

?PRODUCT"="3f0/3b17/100"信息要根据打印机不同做相应修改，把打印机用usb连接至路由器后，通过putty，利用命令：

lsusb-v|grep ID

???获得类似以下信息：

Bus001Device001:ID1d6b:0002Linux Foundation2.0root hub Bus001Device002:ID03f0:3b17Hewlett-Packard LaserJet M1005 MFP?

?

3、设置p910nd，安装了上述的openwrt固件，可略过此步，否则：vi/etc/config/p910nd?编辑加入一下内容：

config p910nd

option device/dev/usb/lp0

option port0

option bidirectional1

option enabled1

4、设置防火墙

vi/etc/config/firewall?，在尾部追加一下内容：

#Allow printer

config rule

option src lan

option proto tcp

option dest_port9100

option target ACCEPT?

?最后：

?/etc/init.d/p910nd enable

?reboot

??

以上就是在openwrt里面的配置，下面是在里面的配置

***********************part I电脑端安装设置以win7系统为例

**************************??

5、设备和打印机-添加打印机-添加本地打印机-创建新端口（端口类型Standard tcp/ip port）-IP地址：路由地址（192.168.5.1）（根据自己路由地址更改），端口名称默认，查询那个钩掉

点下一步就可以添加端口了

6、安装驱动（以HP为例，最后一步会让选择端口，选列表192.168.1.1那个），计算机安装打印机官方驱动。

?

至此，打印机服务器安装成功，就可以直接打印了。

本文由品质电器生活科技+友情提供赞助?

?

?Click on the Start button and select Devices and Printers.

?Click on"Add a printer."

?In the Add Printer dialog select"Add a local printer."

?Select"Create a new port:"and set the type of port to"Standard TCP/IP Port".

Then click Next.

?In the"Hostname or IP address:"field enter the IP address of your router.

?The"Port name:"field may be set to something you like.

?De-select"Query the printer and automatically select the driver to use,"then click next.

?The computer will then attempt to detect the TCP/IP port.This will take some time and will most likely fail.Failing this step is not a problem.

?On the"Additional port information required"page set the device type to Custom and click"Settings…"

?Verify the Printer Name or IP Address.The Protocol should be set to"Raw"

and the Raw Settings Port Number should be9100.Leave LPR Settings

and SNMP Status Enabled empty or de-selected.Then click OK.

?Select the correct printer driver and click next.You may need to install drivers if they are not already available.

?Finish the remaining printer installation wizard steps as needed.The printer should now be installed and working!

?Click on the Start button and select Devices and Printers.

?Click on"Add a printer."

?In the Add Printer dialog select"Add a local printer."

?Select"Create a new port:"and set the type of port to"Standard TCP/IP Port".

Then click Next.

?In the"Hostname or IP address:"field enter the IP address of your router.

?The"Port name:"field may be set to something you like.

?De-select"Query the printer and automatically select the driver to use,"then click next.

?The computer will then attempt to detect the TCP/IP port.This will take some time and will most likely fail.Failing this step is not a problem.

?On the"Additional port information required"page set the device type to Custom and click"Settings…"

?Verify the Printer Name or IP Address.The Protocol should be set to"Raw"

and the Raw Settings Port Number should be9100.Leave LPR Settings and SNMP Status Enabled empty or de-selected.Then click OK.

?Select the correct printer driver and click next.You may need to install drivers if they are not already available.

?Finish the remaining printer installation wizard steps as needed.The printer should now be installed and working!

?Click on the Start button and select Devices and Printers.

?Click on"Add a printer."

?In the Add Printer dialog select"Add a local printer."

?Select"Create a new port:"and set the type of port to"Standard TCP/IP Port".

Then click Next.

?In the"Hostname or IP address:"field enter the IP address of your router.

?The"Port name:"field may be set to something you like.

?De-select"Query the printer and automatically select the driver to use,"then click next.

?The computer will then attempt to detect the TCP/IP port.This will take some time and will most likely fail.Failing this step is not a problem.

?On the"Additional port information required"page set the device type to Custom and click"Settings…"

?Verify the Printer Name or IP Address.The Protocol should be set to"Raw"

and the Raw Settings Port Number should be9100.Leave LPR Settings and SNMP Status Enabled empty or de-selected.Then click OK.

?Select the correct printer driver and click next.You may need to install drivers if they are not already available.

?Finish the remaining printer installation wizard steps as needed.The printer should now be installed and working!