模具专业英语
模具专业英语
一、入水:gate
进入位:gate location
水口形式:gate type
大水口:edge gate
细水口:pin-point gate
水口大小:gate size
转水口:switching runner/gate
唧嘴口径:sprue diameter
二、流道: runner
热流道:hot runner,hot manifold
热嘴冷流道: hot sprue/cold runner
唧嘴直流: direct sprue gate
圆形流道:round(full/half runner
流道电脑分析:mold flow analysis
流道平衡:runner balance
热嘴:hot sprue
热流道板:hot manifold
发热管:cartridge heater
探针: thermocouples
插头:connector plug
插座:connector socket
密封/封料:seal
三、运水:water line
喉塞:line lpug
喉管:tube
塑胶管:plastic tube
快速接头:jiffy quick connector plug/socker 四、模具零件:mold components
三板模:3-plate mold
二板模:2-plate mold
边钉/导边:leader pin/guide pin
边司/导套:bushing/guide bushing
中托司:shoulder guide bushing
中托边L:guide pin
顶针板:ejector retainner plate
托板:support plate
螺丝:screw
管钉:dowel pin
开模槽:ply bar scot
内模管位:core/cavity inter-lock
顶针:ejector pin
司筒:ejector sleeve
司筒针:ejector pin 推板:stripper plate
缩呵:movable core,return core core puller 扣机(尼龙拉勾):nylon latch lock
斜顶:lifter
模胚(架):mold base
上内模:cavity insert
下内模:core insert
行位(滑块):slide
镶件:insert
压座/斜鸡:wedge
耐磨板/油板:wedge wear plate
压条:plate
撑头: support pillar
唧嘴:sprue bushing
挡板:stop plate
定位圈:locating ring
锁扣:latch
扣鸡:parting lock set
推杆:push bar
栓打螺丝:S.H.S.B
顶板:eracuretun
活动臂:lever arm
分流锥:spure sperader
水口司:bush
垃圾钉:stop pin
隔片:buffle
弹弓柱:spring rod
弹弓:die spring
中托司:ejector guide bush
中托边:ejector guide pin
镶针:pin
销子:dowel pin
波子弹弓:ball catch
喉塞: pipe plug
锁模块:lock plate
斜顶:angle from pin
斜顶杆:angle ejector rod
尼龙拉勾:parting locks
活动臂:lever arm
复位键、提前回杆:early return bar
气阀:valves
斜导边:angle pin
术语:terms
承压平面平衡:parting surface support balance
模排气:parting line venting
回针碰料位:return pin and cavity interference
模总高超出啤机规格:mold base shut hight 顶针碰运水:water line interferes withejector pin
料位出上/下模:part from cavith (core) side 模胚原身出料位:cavity direct cut on
A-plate,core direct cut on B-plate.
不准用镶件:Do not use (core/cavity) insert 用铍铜做镶件:use beryllium copper insert 初步(正式)模图设计:preliinary (final) mold design
反呵:reverse core
弹弓压缩量:spring compressed length
稳定性好:good stability,stable
强度不够:insufficient rigidity
均匀冷却:even cooling
扣模:sticking
热膨胀:thero expansion
公差:tolorance
铜公(电极):copper electrode
dowel pin 定位梢
draft 拔模锥度
draw bead 张力调整杆
drive bearing 传动轴承
ejection pad 顶出衬垫
ejector 脱模器
ejector guide pin 顶出导梢
ejector leader busher 顶出导梢衬套
ejector pad 顶出垫
ejector pin 顶出梢
ejector plate 顶出板
ejector rod 顶出杆
ejector sleeve 顶出衬套
ejector valve 顶出阀
eye bolt 环首螺栓
filling core 椿入蕊
film gate 薄膜形浇口
finger pin 指形梢
finish machined plate 角形模板finish machined round plate 圆形模板fixed bolster plate 固定侧模板
flanged pin 带凸缘销
flash gate 毛边形浇口
flask 上箱
floating punch 浮动冲头
gate 浇口
gate land 浇口面
gib 凹形拉紧楔
goose neck 鹅颈管
guide bushing 引导衬套
guide pin 导梢
guide post 引导柱
guide plate 导板
guide rail 导轨
head punch 顶头冲孔
headless punch 直柄冲头
heavily tapered solid 整体模蕊盒
hose nippler 管接头
impact damper 缓冲器
injection ram 压射柱塞
inlay busher 嵌入衬套
inner plunger 内柱塞
inner punch 内冲头
insert 嵌件
insert pin 嵌件梢
king pin 转向梢
king pin bush 主梢
模具相关英语(3)
difference quantity差异量
cause analysis原因分析
raw materials原料
materials物料
finished product成品
semi-finished product半成品
packing materials包材
good product/accepted goods/ accepted parts/good parts良品
defective product/non-good parts不良品disposed goods处理品
warehouse/hub仓库
on way location在途仓
oversea location海外仓
spare parts physical inventory list备品盘点清单
spare molds location模具备品仓
skid/pallet栈板
tox machine自铆机
wire EDM线割
EDM放电机
coil stock卷料
sheet stock片料
tolerance工差
score=groove压线
cam block滑块
pilot导正筒
trim剪外边
pierce剪内边
drag form压锻差
pocket for the punch head挂钩槽
slug hole废料孔
feature die公母模
expansion dwg展开图
radius半径
shim(wedge)楔子
torch-flame cut火焰切割
set screw止付螺丝
form block折刀
stop pin定位销
round pierce punch=die button圆冲子shape punch=die insert异形子
stock locater block定位块
under cut=scrap chopper清角
active plate活动板
baffle plate挡块
cover plate盖板
male die公模
female die母模
groove punch压线冲子
air-cushion eject-rod气垫顶杆
spring-box eject-plate弹簧箱顶板bushing block衬套
insert 入块
club car高尔夫球车
capability能力
parameter参数
factor系数phosphate皮膜化成
viscosity涂料粘度
alkalidipping脱脂
main manifold主集流脉
bezel斜视规
blanking穿落模
dejecting顶固模demagnetization去磁;消磁
high-speed transmission高速传递heat dissipation热传
rack上料
degrease脱脂
rinse水洗
alkaline etch龄咬
desmut剥黑膜
D.I. rinse纯水次
Chromate铬酸处理
Anodize阳性处理
seal封孔
revision版次
part number/P/N料号
good products良品
scraped products报放心品defective products不良品finished products成品
disposed products处理品barcode条形码
flow chart流程窗体
assembly组装
stamping冲压
molding成型
spare parts=buffer备品
模具相关英语(4)
coordinate坐标
dismantle the die折模
auxiliary fuction辅助功能
poly-line多义线
heater band 加热片thermocouple热电偶
sand blasting喷沙
grit 砂砾
derusting machine除锈机degate打浇口
dryer烘干机
induction感应
induction light感应光
response=reaction=interaction感应ram连杆
edge finder巡边器
concave 凹
convex凸
short射料不足
nick缺口
speck瑕疪
shine亮班
splay 银纹
gas mark焦痕
delamination起鳞
cold slug冷块
blush 导色
gouge沟槽;凿槽
satin texture段面咬花
witness line证示线
patent专利
grit沙砾
granule=peuet=grain细粒
grit maker抽粒机
cushion缓冲
magnalium镁铝合金
magnesium镁金
metal plate钣金
lathe车
mill锉
plane刨
grind磨
drill钻
boring镗
blinster气泡
fillet镶;嵌边
through-hole form通孔形式
voller pin formality滚针形式
cam driver铡楔
shank摸柄
crank shaft曲柄轴
augular offset角度偏差
velocity速度
production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火
tempering回火
annealing退火
carbonization碳化
alloy合金
tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂
bracket小磁导
liaison联络单
volatile挥发性
resistance电阻
ion离子
titrator滴定仪
beacon警示灯
coolant冷却液
crusher破碎机
模具工程类
plain die简易模
pierce die冲孔模
forming die成型模
progressive die连续模
gang dies复合模
shearing die剪边模
riveting die铆合模
pierce冲孔
forming成型(抽凸,冲凸)
draw hole抽孔
bending折弯
trim切边
emboss凸点
dome凸圆
模具相关英语(5)
semi-shearing半剪
stamp mark冲记号
deburr or coin压毛边
punch riveting冲压铆合
side stretch侧冲压平
reel stretch卷圆压平
groove压线
blanking下料
stamp letter冲字(料号)
shearing剪断
tick-mark nearside正面压印
tick-mark farside反面压印
冲压名称类
extension dwg展开图
procedure dwg工程图
die structure dwg模具结构图material材质
material thickness料片厚度factor系数
upward向上
downward向下
press specification冲床规格
die height range适用模高
die height闭模高度
burr毛边
gap间隙
weight重量
total wt.总重量
punch wt.上模重量
五金零件类
inner guiding post内导柱
inner hexagon screw内六角螺钉dowel pin固定销
coil spring弹簧
lifter pin顶料销
eq-height sleeves=spool等高套筒pin销
lifter guide pin浮升导料销
guide pin导正销
wire spring圆线弹簧
outer guiding post外导柱
stop screw止付螺丝
located pin定位销
outer bush外导套
模板类
top plate上托板(顶板)
top block上垫脚
punch set上模座
punch pad上垫板
punch holder上夹板
stripper pad脱料背板
up stripper上脱料板
male die公模(凸模)
feature die公母模female die母模(凹模)
upper plate上模板
lower plate下模板
die pad下垫板
die holder下夹板
die set下模座
bottom block下垫脚
bottom plate下托板(底板)
stripping plate内外打(脱料板)
outer stripper外脱料板
inner stripper内脱料板
lower stripper下脱料板
零件类
punch冲头
insert入块(嵌入件)
deburring punch压毛边冲子
groove punch压线冲子
stamped punch字模冲子
round punch圆冲子
special shape punch异形冲子
bending block折刀
roller滚轴
baffle plate挡块
located block定位块
supporting block for location
定位支承块
air cushion plate气垫板
air-cushion eject-rod气垫顶杆
trimming punch切边冲子
stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子
reel-stretch punch卷圆压平冲子
guide plate定位板
sliding block滑块
101个热处理常用英文词汇
1. indication 缺陷
2. test specimen 试样
3. bar 棒材
4. stock 原料
5. billet 方钢,钢方坯
6. bloom 钢坯,钢锭
7. section 型材
8. steel ingot 钢锭
9. blank 坯料,半成品
10. cast steel 铸钢
11. nodular cast iron 球墨铸铁
12. ductile cast iron 球墨铸铁
13. bronze 青铜
14. brass 黄铜
15. copper 合金
16. stainless steel不锈钢
17. decarburization 脱碳
18. scale 氧化皮
19. anneal 退火
20. process anneal 进行退火
21. quenching 淬火
22. normalizing 正火
23. Charpy impact text 夏比冲击试验
24. fatigue 疲劳
25. tensile testing 拉伸试验
26. solution 固溶处理
27. aging 时效处理
28. Vickers hardness维氏硬度
29. Rockwell hardness 洛氏硬度
30. Brinell hardness 布氏硬度
31. hardness tester硬度计
32. descale 除污,除氧化皮等
33. ferrite 铁素体
34. austenite 奥氏体
35. martensite马氏体
36. cementite 渗碳体
37. iron carbide 渗碳体
38. solid solution 固溶体
39. sorbite 索氏体
40. bainite 贝氏体
41. pearlite 珠光体
42. nodular fine pearlite/ troostite屈氏体
43. black oxide coating 发黑
44. grain 晶粒
45. chromium 铬
46. cadmium 镉
47. tungsten 钨
48. molybdenum 钼
49. manganese 锰
50. vanadium 钒
51. molybdenum 钼
52. silicon 硅53. sulfer/sulphur 硫
54. phosphor/ phosphorus 磷
55. nitrided 氮化的
56. case hardening 表面硬化,表面淬硬
57. air cooling 空冷
58. furnace cooling 炉冷
59. oil cooling 油冷
60. electrocladding /plating 电镀
61. brittleness 脆性
62. strength 强度
63. rigidity 刚性,刚度
64. creep 蠕变
65. deflection 挠度
66. elongation 延伸率
67. yield strength 屈服强度
68. elastoplasticity 弹塑性
69. metallographic structure 金相组织
70. metallographic test 金相试验
71. carbon content 含碳量
72. induction hardening 感应淬火
73. impedance matching 感应淬火
74. hardening and tempering 调质
75. crack 裂纹
76. shrinkage 缩孔,疏松
77. forging 锻(件)
78. casting 铸(件)
79. rolling 轧(件)
80. drawing 拉(件)
81. shot blasting 喷丸(处理)
82. grit blasting 喷钢砂(处理)
83. sand blasting 喷砂(处理)
84. carburizing 渗碳
85. nitriding 渗氮
86. ageing/aging 时效
87. grain size 晶粒度
88. pore 气孔
89. sonim 夹砂
90. cinder inclusion 夹渣
91. lattice晶格
92. abrasion/abrasive/rub/wear/wearing resistance (property) 耐磨性
93. spectrum analysis光谱分析
94. heat/thermal treatment 热处理
95. inclusion 夹杂物
96. segregation 偏析
97. picking 酸洗,酸浸
98. residual stress 残余应力
99. remaining stress 残余应力
100. relaxation of residual stress 消除残余应力
101. stress relief 应力释放
机械类常用英语:冲压模具-零件类
punch冲头
insert入块(嵌入件)
deburring punch压毛边冲子
groove punch压线冲子
stamped punch字模冲子
round punch圆冲子
special shape punch异形冲子
bending block折刀roller滚轴
baffle plate挡块
located block定位块
supporting block for location
定位支承块
air cushion plate气垫板
air-cushion eject-rod气垫顶杆
trimming punch切边冲子
stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子
reel-stretch punch卷圆压平冲子
guide plate定位板
sliding block滑块
sliding dowel block滑块固定块
active plate活动板
lower sliding plate下滑块板
upper holder block上压块
upper mid plate上中间板
spring box弹簧箱
spring-box eject-rod弹簧箱顶杆
spring-box eject-plate弹簧箱顶板bushing bolck衬套
cover plate盖板
guide pad导料块
各式模具分类用语英汉对照
landed plunger mold 有肩柱塞式模具burnishing die 挤光模
landed positive mold 有肩全压式模具button die 镶入式圆形凹模
loading shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具
chill mold 冷硬用铸模
loose mold 活动式模具
clod hobbing 冷挤压制模
louvering die 百叶窗冲切模composite dies 复合模具
manifold die 分歧管模具
counter punch 反凸模
modular mold 组合式模具
double stack mold 双层模具multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模
offswt bending die 双折冷弯模具extrusion die 挤出模
palletizing die 叠层模
family mold 反套制品模具plaster mold 石膏模
blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具
fantail die 扇尾形模具
pressure die 压紧模
fishtail die 鱼尾形模具
profile die 轮廓模
flash mold 溢料式模具progressive die 顺序模
gypsum mold 石膏铸模protable mold 手提式模具
hot-runner mold 热流道模具
prototype mold 雏形试验模具
rsingle cavity mold 单腔模具
yoke type die 轭型模注塑模部分中英文对照塑料成形模具mould for plastics
热塑性塑料模mould for thermoplastics 热固性塑料模mould for thermosets
压缩模compression mould
压注模、传递模transfer mould
注射模injection mould
热塑性塑料注射模injection mould for thermoplastics
热固性塑料注射模injection mould for thermoses
成形零件
定模stationary mould fixed half
动模movable mould moving half
定模座板fixed clamp plate, top clamping plate. top plate
动模座板moving clamp plate. bottom clamping plate. bottom plate
上模座板upper clamping plate
下模座板lower clamping plate
凹模固定板cavity-retainer plate
型芯固定板core-retainer plate
凸模固定板punch-retainer plate
模套chase. bolster. frame
支承板backing plate. supprr plate
垫块spacer parallel
支架ejector housing. mould base leg
模具工程常用词汇英汉对照
designing, to design设计
design modification设计变化
die block模块
fsliding block滑块
location pin定位销
lifting pin顶料销
die plate, front board模板
padding block垫块
stepping bar垫条
upper die base上模座
lower die base下模座
upper supporting blank上承板
upper padding plate blank上垫板
spare dies模具备品spring 弹簧
bolt螺栓
document folder文件夹
file folder资料夹
to put file in order整理资料
spare tools location手工备品仓
first count初盘人
first check初盘复棹人
second count 复盘人
second check复盘复核人
equipment设备
waste materials废料
work in progress product在制品
casing = containerazation装箱
quantity of physical invetory second count
复盘点数量
quantity of customs count
会计师盘,点数量
the first page第一联
filed by accounting department for reference 会计部存查
end-user/using unit(department)使用单位summary of year-end physical inventory bills 年终盘点截止单据汇总表
bill name单据名称
This sheet and physical inventory list will be sent to accounting
department together (Those of NHK will be sent to financial
department)
本表请与盘点清册一起送会计部-(NHK厂区送财会部)
Application status records of year-end physical inventory List and
physical inventory card 年终盘点卡与清册使用-状况明细表
blank and waste sheet NO.
空白与作废单号
plate电镀
mold成型
material for engineering mold testing工程试模材料
not included in physical inventory不列入盘点sample样品
incoming material to be inspected进货待验description品名
steel/rolled steel钢材
material statistics sheet
物料统计明细表
meeting minutes会议记录
meeting type 会别
distribution department分发单位
location地点
chairman主席
present members出席人员
subject主题
conclusion结论
decision items决议事项
responsible department负责单位
pre-fixed finishing date预定完成日approved by / checked by / prepared by核准/审核/承办
PCE assembly production schedule sheet PCE组装厂生产排配表
model机锺
work order工令
revision版次
remark备注
production control confirmation生产确认checked by初审
approved by核准
department部门
模具工程常用词汇英汉对照——2
stock age analysis sheet
库存货龄分析表
on-hand inventory现有库存
available material良品可使用
obsolete material良品已呆滞
to be inspected or reworked
待验或重工
total合计
cause description原因说明
part number/ P/N 料号
type形态
item/group/class类别
quality品质
prepared by制表
notes说明year-end physical inventory difference analysis sheet
年终盘点差异分析表
physical inventory盘点数量
physical count quantity帐面数量difference quantity差异量
cause analysis原因分析
raw materials原料
materials物料
finished product成品
semi-finished product半成品
packing materials包材
good product/accepted goods/ accepted parts/good parts良品
defective product/non-good parts不良品disposed goods处理品
warehouse/hub仓库
on way location在途仓
oversea location海外仓
spare parts physical inventory list备品盘点清单
spare molds location模具备品仓
skid/pallet栈板
tox machine自铆机
wire EDM线割
EDM放电机
coil stock卷料
sheet stock片料
tolerance工差
score=groove压线
cam block滑块
pilot导正筒
trim剪外边
pierce剪内边
drag form压锻差
pocket for the punch head挂钩槽
slug hole废料孔
feature die公母模
expansion dwg展开图
radius半径
shim(wedge)楔子
torch-flame cut火焰切割
set screw止付螺丝
模具专业英语词汇大全
模具专业英语词汇 A abrasion n. 磨损 abrasion resistance n. 耐磨损性 abrasive n. 磨料 accelerator n. 促进剂 accuracy n. 准确性 accurate die casting 精密压铸 air trap 积风 acrylic n. 丙烯酸 /压克力 ì active plate 活动板 additive n. 添加剂 adhere v. 黏附 adhesion n. 黏合 adhesive n. 胶粘剂 air-cushion eject-rod 气垫顶杆 air cushion plate 气垫板 air entrapment n. 困气 anneal v. 退火 assemble v. 总成 B back pressure 背压 bismuth mold 铋铸模 baffle plate 挡块 barrel n. 机筒 /料筒 / bending block 折刀 bottom block 下垫脚 bottom plate 下托板(底板) bushing bolck 衬套 barrel temperature 料筒温度 blush 发 blank through dies 漏件式落料模 burnishi blow molding n. 吹塑成型 blow molding machine n. 吹塑机 brittle adj. 脆性 bubble n. 气泡 burr 毛刺 button d by-product n. 副产品 C calendering n. 压延 carbon steel n. 碳素钢 casting n. 铸造 catalyst n. 催化剂 cavity n. 型腔 chemical resistance n. 耐化学腐蚀性 chip v. 削 /凿
开关按键的注塑模具设计说明书
开关按键的注塑模具设 计说明书 文档编制序号:[KKIDT-LLE0828-LLETD298-POI08]
目录 绪论 (3) 1.模塑工艺规程的编制 (5) 塑件的工艺性分析 (5) (5) (6) 计算塑件的体积和质量 (6) 塑件注塑工艺参数的确定 (7) 塑料成型设备的选取 (7) 2.注塑模的结构设计 (8) 分型面选择 (8) 确定型腔的数目及排列方式 (9) (9) (11) 浇注系统设计 (11) (11) (12) (13) (13) (14) 抽芯机构设计 (14) (14) (14) (15) (15) 滑块和导滑槽设计 (15) 导柱的设计 (15) 推出机构设计 (16) 成型零件结构设计 (16) (16) 3.外壳注塑模具的有关计算 (18)
4.模具加热和冷却系统的设计 (20) 5.模具闭合高度确定 (20) 计算模具的闭合高度 (21) 校核注塑机的开,合模空间 (21) (21) (21) 6.注塑机有关参数的校核 (21) 模具合模时校核 (21) 模具开模时校核 (22) 7.绘制模具总装图和非标零件工作图 (22) 本模具总装图和非标零件工作图见附图 (22) 本模具的工作原理 (22) 结论 (23) 致谢 (24) 参考文献 (25) 绪论 大学的学习即将结束,毕业设计是其中最后一个实践环节,是对以前所学的知识及所掌握的技能的综合运用和检验。随着我国经济的迅速发展,采用模具的生产技术得到愈来愈广泛的应用。 随着工业的发展,工业产品的品种和数量不断增加。换型不断加快。使模具的需要补断增加。而对模具的质量要求越来越高。模具技术在国民经济中的作用越来越显得更为重要。 根据业内专家预测,今年中国塑料模具市场总体规模将增加13%左右,到2005年塑料模具产值将达到460亿元,模具及模具标准件出口将从现在的9000多万美元增长到2005年的2亿美元左右,产值在增长,也就意味着市场在日渐扩大。 相当多的发达国家塑料模具企业移师中国,是国内塑料模具工业迅速发展的重要原因之一。中国技术人才水平的提高和平均劳动力成本低都是吸引外资的优势,所以中国塑模市场的前景一片辉煌,这是塑料模具市场迅速成长的重要因素所在。 按照我国国家标准,模具共分为10大类46个小类,塑料模具是10大类中的l 个大类,共有7个小类:热塑性塑料注塑模、热固性塑料注塑模、热固性塑料压塑
模具专业英文术语大全
模具英语专业术语 模具述语 一、入水:gate 进入位: gate location 水口形式:gate type 大水口:edge gate 细水口: pin-point gate 水口大小:gate size 转水口: switching runner/gate 唧嘴口径: sprue diameter 二、流道: runner 热流道: hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形流道:round(full/half runner 流道电脑分析:mold flow analysis 流道平衡:runner balance 热嘴: hot sprue 热流道板:hot manifold 发热管:cartridge heater 探针: thermocouples 插头: connector plug 插座: connector socket 密封/封料: seal 三、运水:water line 喉塞:line lpug 喉管:tube 塑胶管:plastic tube 快速接头:jiffy quick connector plug/socker 四、模具零件: mold components 三板模:3-plate mold 二板模:2-plate mold 边钉/导边:leader pin/guide pin 边司/导套:bushing/guide bushing 中托司:shoulder guide bushing 中托边L:guide pin 顶针板:ejector retainner plate 托板: support plate 螺丝: screw 管钉:dowel pin 开模槽:ply bar scot 内模管位:core/cavity inter-lock 顶针: ejector pin 司筒:ejector sleeve 司筒针:ejector pin 推板:stripper plate 缩呵:movable core,return core core puller 扣机(尼龙拉勾):nylon latch lock 斜顶:lifter 模胚(架): mold base 上内模:cavity insert 下内模:core insert 行位(滑块): slide 镶件:insert 压座/斜鸡:wedge 耐磨板/油板:wedge wear plate 压条:plate 撑头: support pillar 唧嘴: sprue bushing 挡板:stop plate 定位圈:locating ring 锁扣:latch 扣鸡:parting lock set 推杆:push bar 栓打螺丝:S.H.S.B 顶板:eracuretun 活动臂:lever arm 分流锥:spure sperader 水口司:bush 垃圾钉:stop pin 隔片:buffle 弹弓柱:spring rod 弹弓:die spring 中托司:ejector guide bush 中托边:ejector guide pin 镶针:pin 销子:dowel pin 波子弹弓:ball catch 喉塞: pipe plug
外资企业模具英文常用对话
1. XXX!你现在有空吗,我可以问你一些问题吗? Could I ask you some questions if you are free?/ Are you free now? May I ask you some questions (a question)? 2.请问此产品的面是否为外观面?表面做什么处理?是晒纹/抛光? Can you tell me whether the surface of this part is a visible/esthetic one? What will we do for its surface? Texture or Polishing? 3.请问产品这个面可否加顶针或顶块?产品允许加扁顶针吗? Does this part need an ejector pin or an ejector bar? Can we add an ejector blade? 4.这个产品的柱位我们打算做司筒。(或镶针)可以吗? Can we add ejector sleeves or ejector pins in the boss of this part? 5.产品的这个位置不能出模,我们打算做行位,在此面上会有分模线,你接受吗? There's an undercut at this position and it needs a slider. It will also have a parting line on this side, is that OK? 6.产品里面的这个位置我们打算做斜顶或内行位,有问题吗? We will make the lifter and (inner) slider in this position, will that be a problem? 7.你提供的2D产品图与3D产品图不一致,请问以哪一个图面为准? The 2D and 3D drawing you provided is not the same, can you tell me which one is correct? 8.你提供的3D产品图有的地方没有出模角,有的地方胶位太厚,有的地方胶位太溥,这些产品问题我们可以自己修改吗?修改后会给交给你确认。 There is no draft angle in the 3D drawing, some materials are too thick, and some place are too thin. Can we modify this part by ourselves? We will send the drawing to you for you to check after we modify it.
塑胶模具专业英语
中文英文 机工,机器加工 machining,machine work O环,O形封垫 O ring 下料模,切料模 blanking die 寸进,寸动 inching 工程塑胶 engineering plastics 工模,夹具,支架 jig 干胶,粘著剂,动物胶 glue 干燥时间 drying time 干燥剂 drier dryer 不划一颜色,颜色深浅不均 color non-uni formity 中心浇口 center gate 内衬,衬套,衬蛰 liner 公差,容差 tolerance 分模线,合模线,模缝痕 parting line 切口,缺口 notch 切口,缺料 notch 切边(n) shear edge 化学腐蚀 chemical atching 化学腐蚀 chemical etching 反射 reflection 孔隙,空洞,气泡 void 尺寸稳定性 dimensional sability 手动压机 hand press 支管形喷嘴 nozzle manifold 比重 specific gravity 比热 specific heat 毛状裂痕 hair crack,hair cracking 毛绒 fuzz 毛边,凿纹 burr,flash,fin 水道,水通路 water channel 火花放电 spark discharge 火焰处理 flame treatment,flame treating 片材 sheet 凹痕,缩痕 sink mark,shrink mark 凹槽,内陷,凹陷 undercut 加料,给料,供料 feed 加热,加温 warming,warming up 加热板,热板(盘) heating plate 加热管套,加热缸 heating cylinder,heatin g barrel 加热炉 heating furnace 功率,力率 power factor 半透明 semitransparence,translucence 打眼,钻孔 driling 正余面,交叠,重叠 overlap 永久变形 permanent set,residual strain 白昙,雾状 haze 立式射出成型机 vertical injection mo(u)l ding machine 光彩,光泽 gloss 印刷 printing 同轴往复螺杆式射出成型机 in-line scre w(type)injecton mo(u)lding machine 合成树枝 synthetic resin 合板,集成材 composite wood 合模力,开模力 mo(u)ld clamping force, mo(u)ld locking force 合模线,毛边线 flash line,parting line 合模线,毛边线 spew line,spue line 合模销,导销 leader pin 合模销套,导销衬套 leader pin pushing 合模机构,开模机构 mo(u)ld clamping m echanism 后加工 post processing 后加热 after baking 后成型 postforming 回程销,复归销 return pin 安全系数 safety factor 安全门 safety door 成孔销,心型销,模蕊销 core pin 成孔销托板,动或定模板 core pin plate 成形 forming 成形,模制 mo(u)iding,forming
PR按键类模具设计教程
按键类模具设计
Ⅱ按键类模具设计总则 一、树立正确的观念 (一)什么是模具:模具就是用来生产某种指定产品的工具。即然模具只是生产产品的工具。所以制作模具并不是制模人员的目标。作业合格的产品才是我们一切努力的最终目标,而模具制作是这一过程中至关重要的环节。只有得到合格的产品,模具和模具设计才实现其价值。 (二)什么是按键模:按键模就是用来生产按键类产品的工具,按键类产品有如下共同的特点: 1 产品的尺寸相对较小,而尺寸精度要求高 2 产品一般有较高的表面要求 3 产品结构相对简单,但单件产品要求产量高 4 产品有诸如:电镀,印刷等后道工序 相对应于上述按键类产品的特点,按键类模具也有其相对应的特点: 1 模具精度要求高,一般重要尺寸控制为0.02MM 2 型腔、型芯的强度和表面质量要求高:一般型腔都要做到镜面抛光,故我们在选择工件 材料和加工工艺也要相应选用性能好的S136钢材,热处理后硬度为48-52HRC 3 在产品排布设计时,要设计边框和定位柱,以利于注塑工艺调整,以及产品后加工的固 定,产品运输过程中的包装和保护。 (三)按键类产品使用的材料: 1 ABS 用于空心电镀KEY或空心电镀 2 PC 用于空心透明KEY或实心透明KEY 3 PMMA 用于实心透明KEY 4 按键类产品成型后的处理程序以及模具设计时应注意的地方。 (1)表面电镀 1 整个表面都可以被电镀 (2)侧面和顶面可被电镀而底面不可以电镀 针对表面电镀的产品,模具设计时主要要考虑以下几点 1 产品的底面尽量设计成平面
2 LAYOUT 设计时,KEY间距有适当距离 3 流道上要设计挂点,方便电镀时固定产品, 挂点距离为40-50MM 4 在边框及流道上设计一小平面,方便电镀后检测电镀层的厚度 5 定位柱应朝向产品侧,以保护电镀KEY的表面 2 表面印刷: 1 定位柱的设计应朝向KEY的反面,以保证定位柱不刮破印刷丝网 2 流道边框等不能高于产品的KEY 顶面,以免干涉印刷 3 按键KEY与硅胶产品的装配 大多的按键KEY做好之后,都要装配到硅胶产品上, 装配一般是通过用胶水将按键KEY 粘在硅胶上来完成.所以,产品结构设计时必须设计合适的装配间隙和防呆结构. 二、模具设计: 在完成对产品的分析之后,我们要进入正式的模具设计。因按键类模具属于精度要求较高的模具,故模具设计应从以下几个方面着手分析: ㈠按键类模具的设计精度: 模具精度虽然与加工和年装配密切技术相关,但首先应具有较高的设计精度。如果在设计时没有提出恰当的技术要求,或模具结果本身设计不合理,则无论加工和装配技术有多高,模具的精度永远不可能得到保证,所以: 1.按键模各零部件的设计精度和技术要求要与产品精度相适应。按键模型腔、型芯以及分型面的精度相适应。一般模具的尺寸公差应小于产品公差的三分之一,按公司目前的要求,模具的设计和制造公差应控制在±0.02mm以内。 2.按键模的标准通用零部件,虽然不直接参与注射成型,但其精度却能够间接影响产品精度。为此,按键类模具的模架使用龙记标准模架,顶针及司筒使用进口顶针及司筒、浇口套、定位圈也可使用标准件。 3.按键模的结构必须要具有足够的刚度,防止它们在注射压力和合模力的作用下,发生大的弹性变形,影响产品的精度,故: ①模架及板模框适当加厚,并适当增加支撑柱,以防止模架变形 ②镶块选用优质的S136钢材,粗加工后进行热处理,其硬度达到48-52HRC ③设计合理的结构,比如锥面配合,设计凸块咬合结构类加强整体的刚度。 4.按键模应确保动、定模的对合精度。
模具专业英语——注塑模
Injection Mold Technical Terms 特克内克腾目思 (一)模具专业基本用词 Professional Terms Intensification Factor 增强比 Scientific molding 科学注塑英腾次分克深发克偷 塞音特菲克计数器counter康特 Specific Injection Pressure (Psi)特殊注塑压力 思呗色服克 1.塑料—plastic, resin瑞申油管:Oil pipe 尼龙--------nylon 2.样件—sample 调节板-------adjust plate 3.钢料—steel A板--------a plate 4.注塑机—injection machine, press 定位圈----locating ring 喽客厅令 5.产品—part, product, moulding 斜导柱-----angular pin 安给拉PIN 6.模具—mold, mould, tool B板--------- b plate A 简易模(样板模)—prototype mold B 量产用模具—production mold 7.三维造型(数模)—3D model, 滚珠导套-------ball ejector bush 8.二维产品图—2D part drawing 拽应扁顶针--------blade ejector pin 布累得 9.设计—design 低赛应下模板--------bottom clamping plate 抱腾 10.制造—manufacture, 上模型腔------cavity main insert 11.检验—check, 上模镶件------cavity sub insert 12.测量—measure, 妹试司筒针--------center pin 深特 13.修改—change, modify 下模型芯------core main insert 14.工程更改—engineer change 下模镶针------core pin 15.质量—quality 快乐体下模镶件------core sub insert 16.数量—quantity 宽体踢延迟顶针-------delay ejector pin 17.基准—datum, reference 拉杆限位钉--------distance bolt (二)如何解析2D 产品图?How to read 2D part drawing? 一.产品几何Geometry 顶距限位柱--------distance spacer 1.点—point 销钉-------dowel pin 2.线(边)—line, edge 顶块--------ejector bar 3.面face 顶板导套-----ejector leader pin A 侧面—side塞得 B表面—surface射飞思 C 外观面—appearance surface安皮尔思射飞思4.壁厚—wall thickness 我射克来思顶板导柱----ejector leader pin李德拼 5.加强筋(骨位)—rib 瑞布顶针-------ejector pin 6.孔—hole后顶针地板------ejector plate 7.细长的槽—slot 顶针面板-----ejector retain plate 瑞腾 8.柱位—boss 抱死顶棍------ejector rod
模具专业英文术语大全
实用文案 模具英语专业术语 模具述语开模槽:ply bar scot 内模管位:一、入水:gate core/cavity inter-lock 顶针:ejector pin 进入位:gate location 司筒:ejector sleeve 水口形式:gate type 司筒针:edge gate ejector pin 大水口:推板:细水口:stripper plate pin-point gate 缩呵:gate size movable core,return core core 水口大小:puller switching runner/gate 转水口:扣机(尼龙拉勾):nylon latch lock sprue diameter 唧嘴口径:斜顶:lifter : runner 二、流道模胚(架):mold base hot runner,hot manifold 热流道:上内模:cavity insert : hot sprue/cold runner 热嘴冷流道下内模:core insert : direct sprue gate 唧嘴直流行位(滑块):slide round(full/half runner 圆形流道:镶件:insert mold flow analysis 流道电脑分析:压座/斜鸡:wedge :runner balance 流道平衡耐磨板/油板:wedge wear plate hot sprue 热嘴:压条:plate hot manifold 热流道板:撑头: support pillar cartridge heater 发热管:唧嘴:sprue bushing : thermocouples 探针挡板:stop plate connector plug 插头:定位圈:locating ring connector socket 插座:锁扣:latch seal 封料:/密封扣鸡:parting lock set water line 三、运水:推杆:push bar line lpug 喉塞:栓打螺丝:S.H.S.B tube 喉管:顶板:eracuretun plastic tube 塑胶管:活动臂:lever arm jiffy quick connector 快速接头:分流锥:spure sperader plug/socker 水口司mold components 四、模具零件::bush 垃圾钉:三板模:3-plate mold stop pin 隔片:buffle 二板模:2-plate mold 弹弓柱:导边:/leader pin/guide pin spring rod 边钉弹弓:die spring 导套:边司/bushing/guide bushing 中托司:ejector guide bush 中托司:shoulder guide bushing 中托边:ejector guide pin guide pin :L中托边镶针:ejector retainner plate 顶针板:pin 销子:托板:support plate dowel pin 波子弹弓:ball catch screw 螺丝:: pipe plug dowel pin 管钉:喉塞文案大全. 实用文案 锁模块:lock plate Mold repair 模具维修 angle from pin 斜顶:Molds 模具
模具毕业设计99游戏机按钮注塑模具设计
目录 1引言------------------------------------------------------------------------------------------------------ 3 1.1塑料简介 -------------------------------------------------------------------------------------- 3 1.2注塑成型及注塑模-------------------------------------------------------------------------- 3 2 塑件材料分析------------------------------------------------------------------------------------------- 6 2.1 塑件材料的基本特性----------------------------------------------------------------------- 6 2.2 塑件材料成型性能-------------------------------------------------------------------------- 6 2.3 塑件材料成型条件-------------------------------------------------------------------------- 8 3 塑件的工艺分析 -------------------------------------------------------------------------------------- 9 3.1 塑件的结构设计----------------------------------------------------------------------------- 9 3.2 塑件尺寸及精度---------------------------------------------------------------------------- 11 3.3 塑件表面粗糙度---------------------------------------------------------------------------- 11 3.4 塑件的体积和质量------------------------------------------------------------------------- 12 4 注射成型工艺方案及模具结构的分析和确定------------------------------------------------ 12 4.1、注射成型工艺过程分析[5] ---------------------------------------------------------------- 12 4.2 浇口种类的确定 -------------------------------------------------------------------------- 13 4.3 型腔数目的确定---------------------------------------------------------------------------- 14 4.4 注射机的选择和校核 -------------------------------------------------------------------- 14 4.4.1 注射量的校核 ----------------------------------------------------------------------- 14 4.4.2 塑件在分型面上的投影面积与锁模力的校核------------------------------- 15 4.4.3、模具与注射机安装模具部分相关尺寸校核------------------------------- 15 5注射模具结构设计 ---------------------------------------------------------------------------------- 16 5.1 分型面的设计 ------------------------------------------------------------------------------- 16 5.2 型腔的布局 ---------------------------------------------------------------------------------- 17 5.3 浇注系统的设计---------------------------------------------------------------------------- 18 5.3.1 浇注系统组成 -------------------------------------------------------------------- 18 5.3.2 确定浇注系统的原则----------------------------------------------------------- 18 5.3.3 主流道的设计 -------------------------------------------------------------------- 19 5.3.4 分流道的设计 -------------------------------------------------------------------- 21 5.3.5 浇口的设计 ----------------------------------------------------------------------- 21 5.3.6 冷料穴的设计 -------------------------------------------------------------------- 22 5.4 注射模成型零部件的设计[7] ------------------------------------------------------------- 22 5.4.1 成型零部件结构设计----------------------------------------------------------- 23 5.4.2 成型零部件工作尺寸的计算 ------------------------------------------------- 23 5.5 排气结构设计 ------------------------------------------------------------------------------- 24 5.6 脱模机构的设计---------------------------------------------------------------------------- 25 5.6.1 脱模机构的选用原则----------------------------------------------------------- 25
模具英语专业术语
模具英语专业术语上内模:cavity insert 模具述语下内模:core insert 一、入水:gate行位(滑块):slide 进入位:gate location 镶件:insert 水口形式:gate type 压座/斜鸡:wedge 大水口:edge gate 耐磨板/油板:wedge wear plate 细水口:pin-point gate 压条:plate 水口大小:gate size 撑头: support pillar 转水口:switching runner/gate 唧嘴:sprue bushing 唧嘴口径:sprue diameter挡板:stop plate 二、流道: runner 定位圈:locating ring 热流道:hot runner,hot manifold锁扣:latch 热嘴冷流道: hot sprue/cold runner 扣鸡:parting lock set 唧嘴直流: direct sprue gate推杆:push bar 圆形流道:round(full/half runner 栓打螺丝:S.H.S.B 流道电脑分析:mold flow analysis顶板:eracuretun 流道平衡:runner balance 活动臂:lever arm 热嘴:hot sprue 分流锥:spure sperader 热流道板:hot manifold水口司:bush 发热管:cartridge heater 垃圾钉:stop pin 探针: thermocouples 隔片:buffle 插头:connector plug 弹弓柱:spring rod 插座:connector socket 弹弓:die spring 密封/封料:seal中托司:ejector guide bush 三、运水:water line中托边:ejector guide pin 喉塞:line lpug 镶针:pin 喉管:tube 销子:dowel pin 塑胶管:plastic tube 波子弹弓:ball catch 快速接头:jiffy quick connector plug/socker 喉塞: pipe plug 四、模具零件:mold components 锁模块:lock plate 三板模:3-plate mold斜顶:angle from pin 二板模:2-plate mold斜顶杆:angle ejector rod 边钉/导边:leader pin/guide pin 尼龙拉勾:parting locks 边司/导套:bushing/guide bushing 活动臂:lever arm 中托司:shoulder guide bushing 复位键、提前回杆:early return bar 中托边L:guide pin 气阀:valves 顶针板:ejector retainner plate 斜导边:angle pin 托板:support plate 术语:terms 螺丝:screw 承压平面平衡:parting surface support balance 管钉:dowel pin 模排气:parting line venting 开模槽:ply bar scot 回针碰料位:return pin and cavity interference 内模管位:core/cavity inter-lock模总高超出啤机规格:mold base shut hight 顶针:ejector pin 顶针碰运水:water line interferes withejector pin 司筒:ejector sleeve 料位出上/下模:part from cavith (core) side 司筒针:ejector pin 模胚原身出料位:cavity direct cut on A-plate,core direct cut 推板:stripper plate on B-plate. 缩呵:movable core,return core core puller 不准用镶件:Do not use (core/cavity) insert 扣机(尼龙拉勾):nylon latch lock用铍铜做镶件:use beryllium copper insert 斜顶:lifter 初步(正式)模图设计:preliinary (final) mold design 模胚(架):mold base 反呵:reverse core 弹弓压缩量:spring compressed length 稳定性好:good stability,stable 强度不够:insufficient rigidity 均匀冷却:even cooling 扣模:sticking 热膨胀:thero expansion 公差:tolorance 铜公(电极):copper electrode Mold & die components 模具单元 Mold changing systems 换模系统 Mold core 模芯 Mold heaters/chillers模具加热器 /冷却器 Mold polishing/texturing模具打磨/磨纹Mold repair模具维修
注塑模具英文论文
Low Cost Injection Mold Creation via Hybrid Additive and Conventional Manufacturing 1. Introduction In most industrial applications, the manufacturing cost of a plastic part is mainly governed by the amount of material used in the molding process. Thus, current approaches for plastic part design and manufacturing focus primarily on establishing the minimum part thickness to reduce material usage. The assumption is that designing the mold and molding processes to the minimum thickness requirement should lead to the minimum manufacturing cost. Nowadays, electronic products such as mobile phones and medical devices are becoming ever more complex and their sizes are continually being reduced. The demand for small and thin plastic components for miniaturization assembly has considerably increased in recent years. Other factors besides minimal material usage may also become important when manufacturing thin plastic components. In particular, for thin parts, the injection molding pressure may become significant and has to be considered in the first phase of manufacturing. Employing current design approaches for plastic parts will fail to produce the true minimum manufacturing cost in these cases. Thus, tackling thin plastic parts requires a new approach, alongside existing mold design principles and molding techniques. 1.1 Current research Today, computer-aided simulation software is essential for the design of plastic parts and molds. Such software increases the efficiency of the design process by reducing the design cost and lead time [1]. Major systems, such as Mold Flow and C-Flow, use finite element analysis to simulate the filling phenomena, including flow patterns and filling sequences. Thus, the molding conditions can be predicted and validated, so that early design modifications can be achieved. Although available software is capable of analyzing the flow conditions, and the stress and the temperature distribution conditions of the component under various molding scenarios, they do not yield design parameters with minimum manufacturing cost [2,3]. The output data of the software only give parameter value ranges for reference and leaves the decision making to the component designer. Several attempts have also been made to optimize the parameters in feeding [4–7], cooling [2,8,9], and ejection These attempts were based on maximizing the flow ability of molten material during the molding process by using empirical relation ships between the product and mold design parameters.