最新模具专业英语词汇
Injection Mold Technical Terms
（一）模具专业基本用词Professional Terms
1．塑料—plastic, resin
2．样件—sample
3．钢料—steel
4．注塑机—injection machine, press
5．产品—part, product, moulding
6．模具—mold, mould, tool
A 简易模（样板模）—prototype mold
B 量产用模具—production mold 7．三维造型（数模）—3D model, 3D data
8．二维产品图—2D part drawing
9．设计—design
10．制造—manufacture, build up, construction
11．检验—check, inspection
12．测量—measure, inspection
13．修改—change, modify, correction
14．工程更改—engineer change
15．质量—quality
16．数量—quantity
17．基准—datum, reference
牛角入水-rads gate
（二）如何解析2D 产品图？How to read 2D part drawing?
一．产品几何Geometry
1．点—point
2．线（边）—line, edge
3．面face
A 侧面—side
B 表面—surface
C 外观面—appearance surface 4．壁厚—wall thickness, stock thickness
5．加强筋（骨位）—rib
6．孔—hole
7．细长的槽—slot
8．柱位—boss
9．角—corner
A 圆角—fillet
B 倒角—chamfer
C 尖角—sharp corner 10．斜度—angle, taper
11. 凹槽—recess , groove
二．分模信息Splitting
1．分型线—parting line (P/L), splitting line
2．主分模方向—main direction, line of draw
3．浇口设定—gating
产品标识Part Identification
1．产品名称—part name (P/N)
2．产品编号+版本号—part number + revision (Rev.)
3．型腔号—cavity number
4．材料标记—material symbol
5．模具编号—mold number (no.)
6．日期印—dating insert, date code
7．循环印—cycling code
8．公司标志—company logo
三．技术要求Specification (Special Requirement)
1．项目启动表Kick-off sheet
1）项目名称—program name, project name
2）产品名称—part name, product name, part description
3）产品编号—part number (P/N)
4）客户模号—customer mold no.
5）项目启动日期—kick off date, start date
6）项目完成日期—due date,lead time
7）内模件用钢—tool steel
8）型腔数量—number of cavities
9）数据文件编号—data file no.
10）注塑材料—resin, plastic, raw material
11）收缩率—shrink, shrinkage, shrink factor
12）注塑机吨位—molding machine size, injection machine size 13）成型周期—cycle time
14）型腔光洁度—cavity polish
15）型芯光洁度—core polish
16）皮纹（晒纹）—texture, grain
17）拔模斜度—draft angle, removal taper
18）注塑件颜色及光泽—molded color & gloss
19）模具加工地—manufacturing facility
20）热流道供应商—manifold manufacturer, manifold supplier
21）浇口位置—gate location / position
22）浇口类型—gate type
23）产品标识—stamp information, part identification
24）特殊要求—special instructions
25）安全模数—safe steel
2．产品质量及外观要求Part Quality & Appearance Requirement 1）尺寸及公差Dimension & Tolerance
①重要尺寸—critical dimension, important dim., key dim.
②理论尺寸—nominal dimension
③实际尺寸—actual dimension
④公差—tolerance
⑤公差带—tolerance range
⑥尺寸超差—dimension deviation
⑦接受（合格）—accept, OK
⑧拒绝（不合格）—reject, refuse, obsolete, NG
⑨让步接受—concession, special admit
⑩返工—re-work
2）产品缺陷（常见的）Defects (normal)
①缩水—sink mark, shrinkage
②飞边，毛边—flash, burr
③段差—mismatch discrepancy
④银丝纹，蛇纹—snake marks, streak
⑤弯曲，变形—warpage, distortion
⑥打不饱（缺料）—short shot
⑦熔接线—weld line
⑧多胶—unwanted plastic
⑨拉伤—damage
3．产品外观Part Appearance
①产品颜色—part color
②产品光泽—gloss
③皮纹粒度—grain
4．常用词汇、词组及短语Normal Word, Short Sentence
1）单边—per side
2）双边—both sides
3）加入，添加—add, incorporate
4）去除，取消—remove, cancel
5）满足…的要求，符合，与…要求一致—according to, conform to, satisfy, meet 6）要求，需要—require, need, demand
7）确认—be approved, agreed by …
8）允许—permit, allow
9）在…范围之内—within
10）不可以，不允许，禁止—free from, prevent, avoid
11）…，除非有另指—…unless otherwise specified
12）…或少于—…or less
13）自动化运作—automatic operation
14）未注尺寸（详细形状）见三维造型
Non dimensioned contour (detailed shape) see 3D model.
15）分型线上的飞边（披缝）或段差应小于…
Burrs or discrepancy on the P/L shall be … or less.
四．标题栏Title Block
1．产品名称—part name
2．图纸编号 + 版本号（索引号）—drawing no. + level (index)
3．一般公差—general tolerance
（三）如何阅读制模标准？How to read tooling standard?
一．模具结构术语Mold Construction Terms
A．模架Mold Base
1．模架量化特征Measurement Feature
①长X 宽X 高—Length X Width X Height
②模具高度尺寸（模厚）—stack height of mould
③模具重量—total weight of mould, mould thickness
2．定模底板—front plate, top clamping plate, clamp plate, clamping plate 3．定模板—cavity plate, fixed mould plate, A – plate
4．动模板—core plate, moving mould plate, B – plate
5．浮动板—floating plate
6．支撑板—support plate, backing plate
7．间隔板,方铁—support blocks, rails, risers, spacer block
8．顶杆固定板—retaining plate, ejector retaining plate
9．顶板—ejector plate，bottom clamping plate
10．动模底板—back plate
11．导柱—guide pillar, leader pin, guide pin
12．导套—guide bush, leader pin bush
13．复位杆—return pin, push-back pin
14．弹簧—spring
15．撑头—support pillar
16．顶针板导柱、导套—ejection guide pin / bush
17．垃圾钉—stop pin, stop button
18．模脚—standing-off pillars
19．标牌—plaque scutcheon
B．成型零部件moulding components
20．型芯—core insert
21．型腔—cavity insert
22．镶针—core pin
23．镶块—sub-insert, split
24．滑块—slide, sliding split
25．斜顶—lifter, angled-lift split
A 斜顶头—lifter head
B 斜顶杆—lifter rod, lifter shaft
C 斜顶连接块——lifter coupling
D 斜顶导向块——lifter guide
E 斜顶导滑块——lifter Gib
26．成型顶杆—moulding face pin, form pin
C．浇注系统Feed System
1．塑料Plastic
a．主流道—sprue
b．分流道runner
①主分流道—main runner②二级分流道—branch runner
分流道断面形状cross-sectional shape of runner
①圆形—full round
②半圆形—semicircular
③梯形—trapezoidal
c．浇口gate
常用浇口形式normal gate type :
①边缘浇口（J型浇口）—edge gate, J – gate
②侧浇口—side gate
③潜伏式浇口—sub-gate, cashew gate, subsurface gate, submarine gate
潜顶针—subgate to pin
④潜伏式二次浇口(隧道式浇口) —tunnel gate onto feeder post
⑤点浇口—pin gate
⑥直接浇口(主流道型浇口) —sprue gate, direct gate
⑦护耳式浇口—tab gate
d．模腔—impression
e．冷料井—cold slug well
f．热流道—hot runner
2．模具零件mold components
a．定位圈—locating ring, location ring, register ring
b．浇口套—sprue bush
c．挡圈—stop ring
d．浇口镶块—gate insert
e．热流道板—manifold
f．热嘴—hot drop
D．分型面及其锁紧、排气Parting Surface, inter-locking & venting 1．分型线—parting line ( P/L )
2．镶拼线—bodyline, joint line
3．平/ 不平的分型面—flat / non – flat parting surface
4．封胶面—shut off surfaces, seal-off surfaces
5．擦穿位—shut off
6．碰穿位—kiss-off
7．管位—parting line lock
8．分型面的释放(避空) —relief of parting surface
9．分型面的平衡—balancing of parting surface
10．锁紧角度—locking angle
11．锁紧力—clamping force
12．锁模块—safety strap
13．精定位—Interlock, die lock
14．困气—air trap
15．排气槽—vent, vent slot
16．撬模坑--- pry slot
17．计数器--- shot counter/ cycle counter
E．滑块机构Slide
1．驱动Actuation
①斜导柱—angle pin, horn pin, cam pin
②弹簧—spring
③油缸—hydraulic cylinder
2．制动Detention
①滑块固定器—slide retainer
②弹簧制动器—spring-loaded detention (plunger)
③挡钉、挡板—stop pin, stop plate, slide stop
3．导轨—gib, guide strip,center guide
4．锁紧块（楔紧块）—heel block, locking heel, wedge block, chase block,slide driver 5．耐磨片—wear plate, wear strip
6．压板—retainer,gib
7．螺钉—screw
8．定位销—dowel pin
9．行位扣—slide lock / slide retainer
10． flat ejector pin 扁顶针
F．斜顶机构Lifter
1．斜顶头—lifter head
2．斜顶杆—lifter rod, lifter shaft
3．斜顶固定块—lifter rod retainer
4．斜顶导向块—lifter guide
5．开口销—split pin
6．固定板（压板）—retainer plate
7．耐磨片—wear plate
8．铜导套—bronze bushing
9．导套固定板—bushing retainer
10．衬套—spacer
11．导轨—L – gib
12．导轨---T-Gib
13．滑动块—slide
14．连接块—U-Coupling
G．顶出系统Ejection System
1．基本词汇Basic Word
①顶出行程—ejection stroke
②模具开档—daylight
③粘模—stick on
④产品脱模—part is push off from, clear part of mould, separation of part 2．顶板机构Ejector plate assembly
①顶板—ejector plate
②顶板固定板—retaining plate
③推板—stripper plate
④推板导柱—ejector guide pin
⑤推板导套—ejector guide bush
⑥撑头—support pillar
⑦限位块—stop block,stroke block
3．复位机构Return System
①复位杆（回程杆）—return pin, push – back pin
②垃圾钉—stop pin, stop button
③压簧—compressed spring
④碟簧—a stack of “Belleville” washers
⑤早复位机构—early return system
⑥强制复位机构—positive return system
4．顶出方法Ejection Techniques
1）顶杆顶出—pin ejection
2）顶管顶出—sleeve ejection
3）顶块顶出—bar ejection
4）扁顶顶出—blade ejection
5）顶板顶出—stripper ejection
6）油缸顶出—hydraulic ejection
7）气顶—air ejection
8）阀门顶出—valve ejection
5．顶出元件Ejection Elements
1）拉料杆—sprue puller, sucker pin
2）顶杆—ejector pin
3）阶梯式顶杆—stepped ejector pin
4）顶管—ejection sleeve, sleeve
5）扁顶—ejector blade, slabbed off ejector pin
6）顶块—stripper bar
7）顶环—stripper ring
8）推板—stripper plate
9）加速顶—accelerated ejection
10）直顶----straight lifter/EJECTOR BAR
6．顶出辅助机构Supplementary operating system 1）弹簧柱塞器—spring – loaded plunger
2）弹珠定位器—ball catch system
3）插销式锁扣—Latch – lock
4）尼龙拉杆装置—friction puller device
7．电器元件Electric Components
1）压力传感器—pressure transducer
2）限位开关—limit switch
F．冷却系统Cooling System
1．基本词汇Basic Word
1）温差—temperature variation
2）水孔（水道）—waterlines, water-ways, flow-way, channel
3）水路—cooling circuit
4）水路示意图—water schematic, schematic circuit
5）冷却液—coolant, coolant fluid
6）内连接—interconnect
7）外连接—external connection
8）出口、入口—outlet、inlet
9）漏水—water leakage
2．水路分布Circuits
1）阶梯式水路—stepped system
2）分隔板水路—baffled hole system
3）斜孔式水路—angled hole system
3．水路元件Components
1）闷头（螺塞、止水栓）—（threadless）brass pressure plug : female plug & male 2）隔水片—baffle
3）密封圈—O – ring
4）快插水路接头—quick disconnect fitting, quick connection adaptor
5）弯头—elbow
6）偶合器（连接器、接头）—adaptor (including a plug & a socket)
7）橡皮管—rubber hose
8）分水板,集水块—water manifold
G．螺纹、螺纹孔& 螺钉Thread, thread hole & screw
1．螺纹—thread
2．管螺纹—pipe thread
3．螺纹孔—screw hole, tapped hole
4．起吊孔—handling hole, jack screw hole, eye bolt hole
5．螺钉—screw
6．内六角螺钉—socket headed cap screw （s.h.c.s.）
7．沉头螺钉—flat headed cap screw （f.h.c.s）
8．螺栓—bolt
9．螺母—nut
10．锁紧螺母—locknut
11．螺纹标准Thread Standard
①公制标准—Metric
②英制标准—Imperial
③英制管螺纹标准—British Standard Pipe thread （BSP）
④美制管螺纹标准—NPT
⑤美制粗螺纹标准—United Coarse thread （UNC）
⑥美制细螺纹标准—United Fine thread （UNF）
H．润滑Lubrication
1．润滑槽—grease groove
2．加油管—grease line
3．油杯—lubrication fitting
I．测量仪器Measuring Instruments
1．游标卡尺—vernier caliper
2．千分尺—micrometer
3．高度规—height gauge
4．刻度规—dial gauge
5．三坐标测量仪（三次元）—Coordinate Measure Machine（CMM）
6．塞规—pin gauge
7．圆角量规—radii gauge
8．轮廓投影机—profile projector
J．注塑机参数Injection Machine Parameter
1．注塑机规格参数Injection Machine Specification
①锁紧类型clamp type
a．油缸—hydraulic b．肘杆式—toggle
②垂直注塑机导柱间距—tie bar vertical clearance
③水平注塑机导柱间距—tie bar horizontal clearance
④台板尺寸—platen dim.
⑤最小/ 最大模厚—mold height Min. / Max., Min. / Max. mold thickness
⑥最小/ 最大注塑机开档—open daylight Min. / Max.
⑦锁紧行程—clamp stroke
⑧锁紧力—clamping force
⑨顶出行程—ejector stroke
⑩顶出力—ejector force
2．试模工艺参数Moulding Process Parameter, machine setting
①时间Timer（TM）, sec
a．
b．注塑（充填）时间—filling time, injection time
c．冷却时间—cooling time
d．补缩时间—packing time
e．保压时间—holding time
f．
g．成型周期—cycle time
②速率、速度Velocity, %、speed, in/sec
a．注塑（充填）速度—injection speed
b．保压速率—hold pressure velocity
c．螺杆转速—screw rotation speed
③压力Pressure（Prs.）, psi
a．
b．注塑压力—injection pressure
c．保压压力—hold pressure
d．
e．回压（背压）—back pressure
④温度Temperature（Temp.）, °F
a．注塑机喷嘴温度—nozzle temp.
b．
c．料筒前段、中段、后段温度—barrel front、middle、rear temp.
d．模温—mould temp.
e．
f．料温—purged resin melt temp.
g．空射料温—air shot melt temp.
模具专业英语词汇大全
模具专业英语词汇 A abrasion n. 磨损 abrasion resistance n. 耐磨损性 abrasive n. 磨料 accelerator n. 促进剂 accuracy n. 准确性 accurate die casting 精密压铸 air trap 积风 acrylic n. 丙烯酸 /压克力 ì active plate 活动板 additive n. 添加剂 adhere v. 黏附 adhesion n. 黏合 adhesive n. 胶粘剂 air-cushion eject-rod 气垫顶杆 air cushion plate 气垫板 air entrapment n. 困气 anneal v. 退火 assemble v. 总成 B back pressure 背压 bismuth mold 铋铸模 baffle plate 挡块 barrel n. 机筒 /料筒 / bending block 折刀 bottom block 下垫脚 bottom plate 下托板(底板) bushing bolck 衬套 barrel temperature 料筒温度 blush 发 blank through dies 漏件式落料模 burnishi blow molding n. 吹塑成型 blow molding machine n. 吹塑机 brittle adj. 脆性 bubble n. 气泡 burr 毛刺 button d by-product n. 副产品 C calendering n. 压延 carbon steel n. 碳素钢 casting n. 铸造 catalyst n. 催化剂 cavity n. 型腔 chemical resistance n. 耐化学腐蚀性 chip v. 削 /凿
模具专业英文术语大全
模具英语专业术语 模具述语 一、入水：gate 进入位： gate location 水口形式：gate type 大水口：edge gate 细水口： pin-point gate 水口大小：gate size 转水口： switching runner/gate 唧嘴口径： sprue diameter 二、流道: runner 热流道： hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形流道：round(full/half runner 流道电脑分析：mold flow analysis 流道平衡:runner balance 热嘴： hot sprue 热流道板：hot manifold 发热管：cartridge heater 探针: thermocouples 插头： connector plug 插座： connector socket 密封/封料： seal 三、运水：water line 喉塞：line lpug 喉管：tube 塑胶管：plastic tube 快速接头：jiffy quick connector plug/socker 四、模具零件： mold components 三板模：3-plate mold 二板模：2-plate mold 边钉/导边：leader pin/guide pin 边司/导套：bushing/guide bushing 中托司：shoulder guide bushing 中托边L：guide pin 顶针板：ejector retainner plate 托板： support plate 螺丝： screw 管钉：dowel pin 开模槽：ply bar scot 内模管位：core/cavity inter-lock 顶针： ejector pin 司筒：ejector sleeve 司筒针：ejector pin 推板：stripper plate 缩呵：movable core,return core core puller 扣机（尼龙拉勾）：nylon latch lock 斜顶：lifter 模胚（架）： mold base 上内模：cavity insert 下内模：core insert 行位（滑块）： slide 镶件：insert 压座/斜鸡：wedge 耐磨板/油板：wedge wear plate 压条：plate 撑头: support pillar 唧嘴： sprue bushing 挡板：stop plate 定位圈：locating ring 锁扣：latch 扣鸡：parting lock set 推杆：push bar 栓打螺丝：S.H.S.B 顶板：eracuretun 活动臂：lever arm 分流锥：spure sperader 水口司:bush 垃圾钉：stop pin 隔片：buffle 弹弓柱：spring rod 弹弓:die spring 中托司：ejector guide bush 中托边：ejector guide pin 镶针：pin 销子：dowel pin 波子弹弓：ball catch 喉塞: pipe plug
模具专业术语英语单词
1)Designer-设计师。 2)Assembly drawing-模具组装图。 3)Mold layout-模具结构图。 4)2D product drawing-2D产品图。 5)3D product data-3D产品数据。 6)Part drawing-散件图。 7)Insert molding-镶件模。 8)2color mold/Double injection tool-双色模。 9)Hydraulic system-油/水压系统。 10)Parting line-分模线。 11)Air venting-排气槽。 12)Cooling system-冷却系统。 13)Screw-镙丝。 14)Hot runner system-热流道。 15)Valve gate-伐针入水口。 16)Fan gate-扇型入水口。 17)Pin point gate-针点进胶。 18)Moon gate/Banana gate-香蕉，象牙入水口。 19)Submarine gate-潜水口。 20)Injection machine tonnage-注塑机吨数。 21)Number of cavity-穴数。 22)Steel-钢材。 23)Copper-铜。 24)Tungsten copper-钨铜。 25)Beryllium copper-铍铜。 26)Hardening-加硬/淬火。 27)Tempering-回火。 28)Chroming-电镀。 29)Painting-喷漆。 30)Resin-胶材。 31)Printing-丝印。 32)Texturing-嗮纹/咬花。 33)Socket screw-带肩镙丝。 34)Inter lock/Straight lock-模锁。 35)Mold lock-运输块。 36)3plate mold-3板模。 37)Hot runner plate-热流道板。
模具专业术语大全
模具专业术语大全
punch冲头 insert入块(嵌入 件)deburringpunch 压毛 边冲子groovepunch 压线冲子stampedpunch 字模冲子roundpunch 圆冲子 specialshapepunch 异形冲子bendingblock 折刀 roller滚轴 baffleplate 挡块 locatedblock 定位块supportingblockforlocatio n定位支承块 topplate上托板（顶板） topblock上垫脚 punchset上模座 punchpad上垫板 punchholder 上夹板 stripperpad 脱料背板 upstripper上脱料板 maledie公模(凸模) innerguidingpost 内导柱innerhexagonscrew 内六角螺钉dowelpin 固定销 coilspring弹簧 lifterpin顶料销 模具零件英语词汇 aircushionplate 气垫板 air-cushioneject-rod 气垫顶杆 trimmingpunch 切边冲子 stiffening ribpunch =stinger 加强筋冲子 reel-stretch punch 卷圆压平冲 子 guideplate 定位板 slidingblock 滑块 slidingdowelblock 滑块固定块 activeplate 活动板 lowerslidingplate 下滑块板 upperholderblock 上压块 模具模板英语词汇 featuredie 公母模 femaledie 母模(凹 模)upperplate 上 模板 lowerplate 下模板 diepad下垫板 dieholder 下夹板 dieset下模座 bottomblock 下垫脚 模具五金零件英语词汇eq- height sleeves=spool 等高 套筒 pin销 lifterguidepin 浮升导料销 guidepin导正销 uppermidplate 上中间板 springbox 弹簧箱 spring-boxeject-rod 弹簧箱顶杆 spring-boxeject-plate 弹簧箱顶板 bushingbolck 衬套 coverplate 盖板 guidepad 导料块 outerstripper 外脱料板 innerstripper 内脱料板 lowerstripper 下脱料板 ribbonpunch 压筋冲子 bottomplate 下托板(底 板)strippingplate 内 外打(脱料板)outerstripper 外脱料板 innerstripper内脱料板 lowerstripper下脱料板 coverplate盖板 wirespring 圆线弹簧 outerguidingpost 外导柱 stopscrew 止付螺丝 locatedpin 定位销 outerbush 外导套 模具冲压英语词汇 extensiondwg 展开图 proceduredwg 工程图 diestructuredwg 模具结构图 material材质 materialthickness 料片厚度 pressspecification 冲床 规格dieheightrange 适用模高 dieheight闭模高度 burr毛边 gap间隙 punchwt.上模重量 模具工程类英语词汇
模具英语词汇表汇编
模具英语词汇表 A abrasive grinding 强力磨削abrasive['breisiv] a.磨料的, 研磨的 absence ['bs ns] n.. 不在，缺席accessory[k'ses ri] n.附件 accommodate['k m deit] v. 适应 accordingly['k:di li] adv.因此,从而,相应地
accuracy['kjur si] n精度,准确性 actuate['ktjueit] vt.开动(机器), 驱动 adequate['dikwit] a. 足够的adhesive[d'hi:siv] n. 粘合剂 adjacent['d eisnt] a. 邻近的 adopt['d pt] vt. 采纳advance [d'v:ns] n.进步advisable [d'vaizbl] adj. 可取的agitate['d iteit] v. 摇动 a large extent 专门大程度algorithm ['l ri m] n. 算法 align ['lain] v 定位，调准alignment['lainm nt] n. 校直 all-too-frequent 频繁allowance['l uens] n. 容差, 余量 alternate[':lt nit]v.交替,轮流 alternative[:l't:n tiv]
n. 替换物 alternatively[:l't:n t ivli] ad. 做为选择, 也许aluminum[lju'minj m] n.铝 ample['mpl] adj. 充足的analysis ['n l sis] n. 分析 ancillary['nsil ri] a.补助的, 副的 angular ['jul] adj. 有角的 annealing['li:li ] n.退火 aperture ['p t ] n.孔applied loads 作用力appropriate ['pr uprieit] a. 适当的 arc[a:k] n.弧, 弓形 arise['raiz] vi. 出现, 发生 arrange['reid] v. 安排article['a:tikl] n.制品, 产品 ascertain[s'tein] vt. 确定, 查明
模具专业英语词汇
入水：gate 进入位：gate location 水口形式：gate type 大水口：edge gate 细水口： pin-point gate 水口大小：gate size 转水口：switching runner/gate 唧嘴口径：spray diameter 流道: runner 热流道：hot runner, hot manifold 热嘴冷流道: hot spray/cold runner 唧嘴直流: direct spray gate 圆形流道：round(full/half runner 流道电脑分析：mold flow analysis 流道平衡:runner balance 热嘴：hot spray 热流道板：hot manifold 发热管：cartridge heater 探针: thermocouples 插头：connector plug 插座： connector socket 密封/封料： seal 运水：water line 喉塞：line plug 喉管：tube 塑胶管：plastic tube 快速接头：jiffy quick connector plug 模具零件：mold components 三板模：3-plate mold 二板模：2-plate mold 边钉/导边：leader pin/guide pin 边司/导套：bushing/guide bushing 中托司：shoulder guide bushing 中托边L：guide pin 顶针板：ejector retainner plate 托板：support plate 螺丝： screw 管钉：dowel pin 开模槽：ply bar slot 内模管位：core/cavity inter-lock 顶针：ejector pin 司筒：ejector sleeve 司筒针：ejector pin 模具专业英语 推板：stripper plate 缩呵：movable core, return core puller 扣机（尼龙拉勾）：nylon latch lock 斜顶：lifter 模胚（架）： mold base 上内模：cavity insert 下内模：core insert 行位（滑块）： slide 镶件：insert 压座/斜楔：wedge 耐磨板/油板：wedge wear plate 压条：plate 撑头: support pillar 唧嘴： sprue bushing 挡板：stop plate 定位圈：locating ring 锁扣：latch 扣鸡：parting lock set 推杆：push bar 栓打螺丝：S.H.S.B injection nozzle 射出喷嘴 顶板：eracuretun 活动臂：lever arm 分流锥：spure sperader 水口司:bush 垃圾钉：stop pin 隔片：buffle 弹弓柱：spring rod 弹弓:die spring 中托司：ejector guide bush 中托边：ejector guide pin 镶针：pin 销子：dowel pin 波子弹弓：ball catch 喉塞: pipe plug 锁模块：lock plate 斜顶：angle from pin 斜顶杆：angle ejector rod 尼龙拉勾：parting locks 活动臂：lever arm 复位键、提前回杆：early return bar 气阀：valves 斜导边：angle pin
模具专业术语大全
模具专业术语大全 punch冲头 insert入块(嵌入件)deburringpunch 压毛边冲子groovepunch 压线冲子stampedpunch 字模冲子roundpunch 圆冲子specialshapepunch 异形冲子bendingblock 折刀 roller滚轴 baffleplate 挡块 locatedblock 定位块supportingblockforlocation定位支 承块 topplate上托板（顶板） topblock上垫脚punchset上 模座punchpad上垫板 punchholder 上夹板 stripperpad 脱料背板 upstripper上脱料板maledie 公模(凸模) innerguidingpost 内导柱innerhexagonscrew 内六角螺钉dowelpin 固定销 coilspring弹簧lifterpin 顶料销 模具零件英语词汇 aircushionplate 气垫板 air-cushioneject-rod 气垫顶杆 trimmingpunch 切边冲子stiffening ribpunch =stinger 加强筋冲子 reel-stretch punch 卷圆压平冲 子 guideplate 定位板 slidingblock 滑块 slidingdowelblock 滑块固定块 activeplate 活动板 lowerslidingplate 下滑块板 upperholderblock 上压块 模具模板英语词汇 featuredie 公母模femaledie 母模(凹 模)upperplate 上模板 lowerplate 下模板 diepad下垫板dieholder 下夹板 dieset下模座 bottomblock 下垫脚 模具五金零件英语词汇 eq-height sleeves=spool 等高 套筒 pin销 lifterguidepin 浮升导料销 guidepin导正销 uppermidplate 上中间板 springbox 弹簧箱 spring-boxeject-rod 弹簧箱顶杆spring- boxeject-plate 弹簧箱顶板 bushingbolck 衬套 coverplate 盖板guidepad 导料块 outerstripper 外脱料板 innerstripper 内脱料板 lowerstripper 下脱料板 ribbonpunch 压筋冲子 bottomplate 下托板(底 板)strippingplate 内外打(脱料 板)outerstripper 外脱料板 innerstripper内脱料板 lowerstripper下脱料板 coverplate盖板 wirespring 圆线弹簧 outerguidingpost 外导柱stopscrew 止付螺丝 locatedpin 定位销 outerbush 外导套 模具冲压英语词汇 extensiondwg 展开图 proceduredwg 工程图 diestructuredwg 模具结构图 material材质 materialthickness 料片厚度 pressspecification 冲床规格 dieheightrange 适用模高 dieheight闭模高度 burr毛边 gap间隙 punchwt.上模重量 模具工程类英语词汇
模具专业英文术语大全
实用文案 模具英语专业术语 模具述语开模槽：ply bar scot 内模管位：一、入水：gate core/cavity inter-lock 顶针：ejector pin 进入位：gate location 司筒：ejector sleeve 水口形式：gate type 司筒针：edge gate ejector pin 大水口：推板：细水口：stripper plate pin-point gate 缩呵：gate size movable core,return core core 水口大小：puller switching runner/gate 转水口：扣机（尼龙拉勾）：nylon latch lock sprue diameter 唧嘴口径：斜顶：lifter : runner 二、流道模胚（架）：mold base hot runner,hot manifold 热流道：上内模：cavity insert : hot sprue/cold runner 热嘴冷流道下内模：core insert : direct sprue gate 唧嘴直流行位（滑块）：slide round(full/half runner 圆形流道：镶件：insert mold flow analysis 流道电脑分析：压座/斜鸡：wedge :runner balance 流道平衡耐磨板/油板：wedge wear plate hot sprue 热嘴：压条：plate hot manifold 热流道板：撑头: support pillar cartridge heater 发热管：唧嘴：sprue bushing : thermocouples 探针挡板：stop plate connector plug 插头：定位圈：locating ring connector socket 插座：锁扣：latch seal 封料：/密封扣鸡：parting lock set water line 三、运水：推杆：push bar line lpug 喉塞：栓打螺丝：S.H.S.B tube 喉管：顶板：eracuretun plastic tube 塑胶管：活动臂：lever arm jiffy quick connector 快速接头：分流锥：spure sperader plug/socker 水口司mold components 四、模具零件：:bush 垃圾钉：三板模：3-plate mold stop pin 隔片：buffle 二板模：2-plate mold 弹弓柱：导边：/leader pin/guide pin spring rod 边钉弹弓:die spring 导套：边司/bushing/guide bushing 中托司：ejector guide bush 中托司：shoulder guide bushing 中托边：ejector guide pin guide pin ：L中托边镶针：ejector retainner plate 顶针板：pin 销子：托板：support plate dowel pin 波子弹弓：ball catch screw 螺丝：: pipe plug dowel pin 管钉：喉塞文案大全． 实用文案 锁模块：lock plate Mold repair 模具维修 angle from pin 斜顶：Molds 模具
模具英语专业术语
模具英语专业术语模具的分类: 冲压模(五金模): stamping die 分离模: cutting die 成形模: forming die 塑胶模: plastics mold 注射模: injection mold 压缩模: compression mold 铸塑模: transfer mold 吹塑模: blow mold 吸塑模: suck mold 铸造模: casting die 砂型铸造: sand casting 压铸模: die casting 锻造模: forging die 塑胶模具术语 一、入水：gate 进入位(入水点)：gate location 水口形式：gate type 大水口(侧浇口): edge gate 潜水口: sub-gate 薄膜式水口: film gate 牛角式潜水口: banana gate 扇形水口: fan gate 环形水口: ring gate 二次水口: 细水口：pin-point gate 水口大小：gate size 转水口：switching runner/gate 唧嘴口径：sprue diameter 直接水口: direct gate 二、流道: runner 热流道：hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形(整圆/半圆)流道：round(full/half) runner 矩形流道: rectangle runner 梯形流道: trapezoid runner U形流道: U shape runner 流道电脑分析(模流分析)：mold flow analysis 流道平衡: runner balance
模具专业的英语词汇大全
模具专业的英语词汇大全 一、模具专业英语 入水：gate 进入位：gate location 水口形式：gate type 大水口：edge gate 细水口： pin-point gate 水口大小：gate size 转水口：switching runner/gate 唧嘴口径：sprue diameter 二、流道: runner 热流道：hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形流道：round(full/half runner 流道电脑分析：mold flow analysis 流道平衡:runner balance 热嘴：hot sprue 热流道板：hot manifold 发热管：cartridge heater 探针: thermocouples 插头：connector plug 插座： connector socket 密封/封料： seal 三、运水：water line 喉塞：line lpug 喉管：tube 塑胶管：plastic tube 快速接头：jiffy quick connector plug/socker 四、模具零件：mold components 三板模：3-plate mold 二板模：2-plate mold 边钉/导边：leader pin/guide pin 边司/导套：bushing/guide bushing 中托司：shoulder guide bushing 中托边L：guide pin 顶针板：ejector retainner plate 托板：support plate 螺丝： screw 管钉：dowel pin 开模槽：ply bar scot 内模管位：core/cavity inter-lock
模具常用英文词汇
钣金设计中常用的其它术语 扩孔enlarge hole 自铆self-chinching 全周压毛边all round burr 平头拉钉set-head rivet 表面处理finish 定位销dowel pin 挂钩hook 平头铆钉closed-end rivet 焊接线weld line 塑料固定栓fastener, plastic, push-type 压合胶粘剂pressure sensitive adhesive 尼龙绑带tie wrap, nylon 五金件hardware 泡棉静电导片gasket, foam, emi 贴纸labeling 铍铜静电导片gasket, beck, emi 烤漆paint 圆头螺钉button-head screw 电镀plating 平头螺母nut flush 铭板nameplate 平齐自铆flush, self-clinching 包装packing 紧固螺丝fix screw 铁材零件sheet metal parts 组装assembly 塑料零件plastic parts 凹陷,顶针sink mark 压边铆钉open-end rivet 插孔jack 弹簧螺丝caps 度thick 文字,记号char actor 半冲孔spring slice 角corner 基座chassis 自锁螺母nut self-clenching 承座bracket 轴肘式铆接toggle lock 承架horsing 卡尺caliper 下盖base 打印字模stamp letter 去毛边deburr 推板导住ejector guide 直导套guide bush, straight[straight bushing] 带头导套guide bush, straight {shoulder bushing} 推板导套ejector guide bush[ejector bushing] 定位圈Locating ring 锥形定位件mould bases locating elements 复位杆ejector plate return pin[push-back pin] 限位钉stop pin[stop but ton] 限位块stop block [stop pad] 定距拉杆puller[length]bolt 定距拉板puller[limit]plate 成形推杆forming ejector pin 圆柱头推杆ejector pin with cylindrical head 带肩推杆shouldered ejector pin 扁推杆flat ejector pin 推管ejector sleeve 推块ejector pad 推件板stripper plate 推杆固定板ejector retainer plate ; 推板ejection plate[elector plate] 连接推杆ejector tie rod 冲裁间隙blanking clearance 模具闭合高度die shut height 压力机闭合高度shut height Of press machine 冲模寿命die life 压力中心center Of load 冲模中心center Of die 冲压方向pressing direction 送料方向feed direction 排样blank layout 搭边scrap 进距feed pitch 切边余量trimming allowance 毛刺burr 冲裁力blanking force 弯曲力bending force 拉仲力drawing force 挤压力extruding force 卸料力stripping force 推件力ejecting force 顶件力kicking force 压料力pressure plate force 压边力black holder force 毛坯blank ;
常用模具英语单词
die 模具 figure file, chart file图档 cutting die, blanking die冲裁模progressive die, follow (-on)die 连续模compound die复合模 punched hole冲孔 panel board镶块 to cutedges=side cut=side scrap切边 to bending折弯 to pull, to stretch拉伸 Line streching, line pulling线拉伸engraving, to engrave刻印 upsiding down edges翻边 to stake铆合 designing, to design设计 design modification设计变化 die block模块 folded block折弯块 sliding block滑块 location pin定位销 lifting pin顶料销 die plate, front board模板 padding block垫块 stepping bar垫条 upper die base上模座 lower die base下模座 upper supporting blank上承板 upper padding plate blank上垫板spare dies模具备品 bolt螺栓
模具述语 一、入水：gate 进入位：gate location 水口形式：gate type 大水口：edge gate 细水口：pin-point gate 水口大小：gate size 转水口：switching runner/gate 唧嘴口径：sprue diameter 二、流道: runner 热流道：hot runner, hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形流道：round(full/half runner 流道电脑分析：mold flow analysis 流道平衡:runner balance 热嘴：hot sprue 热流道板：hot manifold 发热管：cartridge heater 探针: thermocouples 插头：connector plug 插座：connector socket 密封/封料：seal 三、运水：water line 喉塞：line lpug 喉管：tube
模具专业英语词汇
Injection Mold Technical Terms （一）模具专业基本用词Professional Terms 塑料—plastic, resin 样件—sample 钢料—steel 注塑机—injection machine, press 产品—part, product, moulding 模具—mold, mould, tool A 简易模（样板模）—prototype mold B 量产用模具—production mold 三维造型（数模）—3D model, 3D data 二维产品图—2D part drawing 设计—design 制造—manufacture, build up, construction 检验—check, inspection 测量—measure, inspection 修改—change, modify, correction 工程更改—engineer change 质量—quality 数量—quantity 基准—datum, reference 牛角入水-rads gate （二）如何解析2D 产品图How to read 2D part drawing 产品几何Geometry 1．点—point 2．线（边）—line, edge 3．面face A 侧面—side B 表面—surface C 外观面—appearance surface 4．壁厚—wall thickness, stock thickness 5．加强筋（骨位）—rib 6．孔—hole 7．细长的槽—slot 8．柱位—boss 9．角—corner A 圆角—fillet B 倒角—chamfer C 尖角—sharp corner 10．斜度—angle, taper 11. 凹槽—recess , groove 分模信息Splitting 分型线—parting line (P/L), splitting line 主分模方向—main direction, line of draw 浇口设定—gating 产品标识Part Identification 产品名称—part name (P/N) 产品编号+版本号—part number + revision (Rev.)
模具专业英语词汇.doc
模具专业英语词汇 landed plunger mold 有肩柱塞式模具burnishing die 挤光模英语站landed positive mold 有肩全压式模具button die 镶入式圆形凹模 loading shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具 chill mold 冷硬用铸模 loose mold 活动式模具 clod hobbing 冷挤压制模 louvering die 百叶窗冲切模composite dies 复合模具 manifold die 分歧管模具 counter punch 反凸模 modular mold 组合式模具 double stack mold 双层模具 multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模 offswt bending die 双折冷弯模具extrusion die 挤出模 palletizing die 叠层模 family mold 反套制品模具 plaster mold 石膏模 blank through dies 漏件式落料模porous mold 通气性模具 duplicated cavity plate 复板模positive mold 全压式模具 fantail die 扇尾形模具 pressure die 压紧模 fishtail die 鱼尾形模具 profile die 轮廓模 flash mold 溢料式模具 progressive die 顺序模 gypsum mold 石膏铸模 protable mold 手提式模具 hot-runner mold 热流道模具prototype mold 雏形试验模具 ingot mold 钢锭模 punching die 落料模
五金模具常用专业术语中英文对照表[1]
五金模具常用专业术语中英文对照表 上模座upper die set成型公form punch 脱料板stripper 垫板subplate/backup plate 下模座die plate滑块CAM slider 垫脚parallel 误检misfeeder 托板mounting plate顶料销kick off 初始管位first start pin带肩螺丝shoulder screw 两用销lifter pin氮气汽缸gas spring 弹簧护套spring cage 拔牙螺丝jack screw 侧冲组件cam section 导正装置guide equipment 漏废料孔slug hole刀口trim line 加强装置enhance equipment 入子insert 护套bushing 整形公restrike forming punch 止挡板stop plate 挂台head 扣位pocket of head 导柱guide post 导套guide bushing 油嘴oil nipple 接刀口mismatch/cookie bites 限位块stop block 挡块stopper 浮块lifter 压块keeper 靠块heel 对正块alignment block 简易模prototype tooling 检具gage/checking fixture 料带图strip layout 闭合高度shut hight 俯视图top view 料带strip 公差tolerance 正视图front view 走位travel 避位/空pocket 退磁demagnetization 间隙clearance 真空热外理vacuum heat treatment 镗孔mill hole 表面外理surface coasting 镀钛TD coasting 沉头counter sink 精锣finish mill 线割wire cutting 穿丝孔first wire hole 斜度taper 镭射laser-cut 上夹板/固定座holder/retainer 下模座lower die set 成刑母公forming die 电火花EDM 码模槽mounting slot 球锁紧固定座ball-lock 导尺rail 球锁紧凸模BALL--LOCK 送料板rail plate 外购out sourcing 倒角chamfer 清角SCRAP CHOPPER 销钉dowel 尖角sharp --angle 普通弹簧coil spring 展开图EXPENSINg DWG 三打螺丝spool 镶件insert 毛刺burr 键销key 插针pilot pin
模具英语专业术语
模具（MOULD/MOLD，TOOL）： CAVITY：前模 CORE：后模（定模） DIMENSION：寸法 GATE：浇口/水口/入水口 PIN GATE：点水口/点浇入水 SIDE GATE：边水口/侧浇入水/大水口APPERANCE SURFACE：体裁面WARPAGE DIRECTION：变形方向 DRAFT ANGEL：脱模斜度 PARTING LINE/P。L：分模线 EJECT PIN/E。P：注塑顶针 BLAST/TEXTURE：喷啥，蚀纹 MIRROR FINISH：镜面（抛光）处理POLISH：抛光 EMD：放电加工 WELD：熔接加工（烧焊） LATHE：车床 MILLING CUTTER：铣刀 MILLING MACHINE：铣床 WIRE CUT：线切割 CNC：主加工中心 POWER DRILL：电钻 DRILLING：钻孔 FRITING：烧结 ANNEALING：淬火 注塑术语（INJECTION） SCREW：螺杆 WELD LINE：熔接线 SINK MARK：缩水 DRAG MARK：脱花 BURR：批锋 FLOW MARK：流纹 SHADOW MARK/GLOSS DIFFERENCE：光影SHORT：缺胶 INJECTION CYCLE：成型周期
注塑英语 型厚大小 Thick size 锁模结构（机绞/直压） Mode locking structure(machine twists/straight pressure) 最大开模距离 The biggest die sinking is away from 动模板最大模具重量 Moves the template maximum mold weight 哥林柱间距 Elder brother forest column spacing 顶出形式（电动五点，油压五点，油压十三点） Goes against the form (electrically operated five spots, flowing tubing head pressure five spots, flowing tubing head pressure 13 spots) 顶出长度 Goes against the length 顶棍孔直径 Goes against the stick hole diameter 顶棍孔中心矩 Goes against the stick hole central moment 螺杆材质（合金） Screw rod material quality (alloy) 螺杆转速 Screw rod rotational speed 最大射出体积 Projects the volume most greatly 最大射出量 Projects the quantity most greatly 射出率 Ejection rate 每10mm射出量（理论） Each 10mm projects the quantity (theory) 射咀直径 Shoots ju the diameter 射咀R值 Shoots ju the R value 射咀空径 Shoots ju the spatial diameter 定位环直径 Locating ring diameter 溶胶能力 Sol ability 驱动方式（全自动/全液压）