模具常用中英文对照
模具常用术语中英文对照
模芯Parting Core
局部视图Partial View
冷料# Cold Slag
线切割 Wire E.D.M
轮廊Contour
螺纹孔 Tapping Hole
连接件 Fittings
斜针Angle Pin
接合Engage
替换镶件Interchangeable Mold Inserts 指定吨位的注塑机Specific Press 水嘴接头Water Fittings
螺纹Eyebolt Thread
回针Stop Pin
二级顶出针 Sub-Leaderd Pin
镶件Mold Insert
加硬Harden
唧嘴Sprue
设计筒图Design Preliminary
名称块表Title Block
版本标识Revision Level
材料清单Stock List
制模Build Mold
手动滑块Hand Slide
漏水测试Leak Test
流道排气Runner V ents
抛光Draw Polish
侧抽芯 Side Action
加强筋 Reinforcing
三角撑 Gusset
柱子Bossed
出模斜度Draft
外廊Contour
落单会议Kick-Off Meeting 装卸孔 Handling Hole
运输安全带 Moldstrap
码模槽 Clamp Slot
撑头Support Pillar
螺牙1/2-13 Eye Bolt 1/2-13Tap 导柱位 Leader Pin Location
耐落胶 Teflon Paste
偏移量 Offset
水塞Water Line Plug
撬模脚 Ppy Slot
重新加工Reworked
配件Components
补偿Compensation
平面度 Parallel
倒角Chamfer
模胚Mold Base
热嘴Hotnozzle
火花机 Edm
熔接线 Weildline
压机Press
晒纹Texturing
梯形Trapezoid
凸缘、法兰 Flange
方铁 Spacer Block
顶针板 Ejector Plate
顶针底板Ejector Retainer Plate
垫板 Retainer Plate
后模镶针Core Pin
拉圾钉 Stop Pin
有托顶针Shoulder Ejector Pin
顶针板导套 Guided Ejection Bushing
针板导柱Guided Ejection Leader Pin
唧嘴 Sprue Bushing
三板模延伸式唧嘴Extension Nozzle Bushing 水口板导套 Runner Stripper Plate Bushing
定位圈(法兰) Locating Ring
管钉(定位销) Dowel Pin
管状管钉 Tubular Dowel
吊环 Safety Hoist Ring
日期印 Dating Insert
环保印 Recycling Insert
气顶 Air Poppet V alve
截水口镶件 Runner Shut-Off Insert
早回 Early Ejector Return
加速项 Accelerated Ejector
客户 Client
产品名 Part Name
产品编号Part No
缩水Shrinkage
版本Rev
模胚Mold Base
下模镶件Core Block
上模镶件Cavity Block
小镶件 Sub-Insert
下模小镶件 Core Sub-Insert
上模小镶件 Cavity Sub-Insert
行位Slide
行位镶件Slide Insert
压条Gib
压紧块(铲机) Jaw
硬片(摩擦片) Wear Plate
水口铁 Runner Bar
上模水口铁 Upper Runner Bar
下模水口铁 Lower Runner Bar
弹簧Spring
水口勾针Sprue Puller Pin
顶针Ejector Pin
撑头Support Pillar
直身锁 Side Lock
斜度锁 Interlock
锁模板 Safety Bar
‘O’令(密封圈) O'Ring
喉塞Plug
隔水片 Baffle
波子螺丝(行位定位螺丝) Ball-Catch
斜顶Lifter
控制开关Switch
回针 Return Pin
斜导柱 Angle Pin
推板 Stripper Plate
A’板A'Plate
B’板B'Plate
方铁(垫铁)Spacer Block
顶针板 Ejector Plate
顶针底板Ejector Retainer Plate
垫板 Retainer Plate
垃圾钉 Stop Pin
有托顶针 Shoulder Ejector Pin
顶针板导套 Guided Ejection Bushing
针板导柱Guided Ejection Leader Pin
唧嘴 Sprue Bushing
三板模延伸式唧嘴Extension Nozzle Bushing 水口板导套 Runner Stripper Plate Bushing
定位圈(法兰) Locating Ring
管钉(定位销) Dowel Pin
管状管钉 Tubular Dowel
吊环 Safety Hoist Ring
日期印 Dating Insert
环保印 Recycling Insert
气顶 Air Poppet V alve
截水口镶件 Runner Shut-Off Insert
早回 Early Ejector Return
加速顶 Accelerated Ejector
扁顶 Blade
出模斜波Draft
手动滑块模具Hand Slide-In Type Mold 回针板 Backup
合模Shutoff
空隙槽 Clearance Slot
导柱及导套 Leader Pin Bushing
水口拉钩Spuer Puller
模框镶件Pocket Insert
成型热固性塑胶模具 Thermoset Mold
三板模 3-Plat Mold
分型面 Parting Line
司筒Ejector Sleeve
垫圈Washer
熔接线(夹水纹)Weldline
吸针Sucker Pin
回针板 Retainer Plate
顶出板 Knock -Out Plate
电动安全开关Electrical-Safety Switch 脱开Cut Of Position
预先决定Preload
缓冲器 Bumper
衬垫Cushion
公差Tolerance
突然性动作 Slam
销针Dowel
钩槽Gib
精磨Finished
通框Through Window
粘后模 Sticking Core
粘水口 Sticking Sprue
夹水纹 Weld Line
变形 Warpage
走水不平均 Filling Uneven
走不齐 Short Shot
挂成品 Part Hanging
漏水 Water Leakage
刮花(擦伤)Galling
困气 Air Trapping
温度 Temperature
注塑模※※※※ction Mold 入水 Gate
试板 Sampling
压力 Pressure
倒圆 Fillet
顶棍 Ejector
顶白 Stress Mark
粘前模 Sticking Cav
名称块表Title Block
版本标识Revision Level
材料清单Stock List
斜导柱(斜边) Angle Pin
A板 A'plate
B板 B'plate
倒扣 Under-Cut
披峰 Flash
缩水 Sink Mark
氮化 Nitride
不规则四边形Trapezoid
连续的 Consecutive
雕刻 Engrave
出模角 Draft
分模面 Parting Surface
擦位 Shut-Off(S/0)
导套 Bushing
回针 Return Pin
加硬 Harden
唧嘴 Sprue
设计筒图Design Preliminary
丝印 Silkprint
不干胶 Adhesive Sticker
导向针 Guide Din
公差 Tolerance
线切割 Wire-Cut
电火花 Edm
抛光 Polishing
蚀纹 Texture
探热针 Thermocouple
三打螺丝毫(限螺丝)Stripper Bolt 盖板 Cover Plate
齿轮 Gear
油唧 Hydraulic Cylinder
司筒 Ejector Sleeve
导柱 Leader Pin
冷料# Cold Slag
线切割 Wire E.D.M.
轮廓 Contour
螺纹孔 Tapping Hole
连接件 Fittings
斜针 Angle Pin
接合 Engage
替换镶件Interchangeable Mold Inserts 指定吨位的注塑机Specific Press
水嘴接头Water Fittings
螺纹 Eyebolt Thread
回针 Stop Pin
二级顶出针 Sub-Leader Pin
镶件 Mold Insert
锁定位 Lock
楔子(铲鸡) Wedge
高产量模量 High V olume Running Mold 剖面图 Cross Section
模具结构Mold Construction 模芯 Parting Core
局部视图Partial View
热流道 Manifold
热嘴 Hot Nozzle
型腔数 Cav No
模号 Mold No
胶料 Material
尺寸 Dimension
重要尺寸Critical Dimension 雕刻 Engrave
托司 EJ.GUIDE PIN
塑胶模具类中英文对照专业术语
塑胶模具类中英文对照专业术语工程部/ Design department: 1) Designer - 设计师。 2) Assembly drawing - 模具组装图。 3) Mold layout - 模具结构图。 4) 2D product drawing - 2D产品图。 5) 3D product data - 3D产品数据。 6) Part drawing - 散件图。 7) Insert molding - 镶件模。 8) 2 color mold / Double injection tool - 双色模。 9) Hydraulic system - 油/水压系统。 10) Parting line - 分模线。 11) Air venting - 排气槽。 12) Cooling system - 冷却系统。 13) Screw - 镙丝。 14) Hot runner system - 热流道。 15) Valve gate - 伐针入水口。 16) Fan gate - 扇型入水口。 17) Pin point gate - 针点进胶。 18) Moon gate / Banana gate - 香蕉,象牙入水口。 19) Submarine gate - 潜水口。 20) Injection machine tonnage - 注塑机吨数。 21) Number of cavity - 穴数。 22) Steel - 钢材。 23) Copper - 铜。 24) Tungsten copper - 钨铜。 25) Beryllium copper - 铍铜。 26) Hardening - 加硬/淬火。 27) Tempering - 回火。
模具术语(中英文对照)
AD-Diameter The tread diameter at the centerline of the tread (EU); also: "T-Diameter"(GT) AD直径:指胎面中心线直径(EU)。又叫T直径(GT) Auto-lock Ear A Lug on the cone ring used to mount the mold/container in the top half of a 60“ NRM Auto-lock press. 导环上的突缘,用于和60“ NRM Auto-lock 硫化机上半部连接。 Bead Ring The tire bead forming ring (also: toe ring) 钢圈,也称toe ring Bead Ring Register The landing and tapered seat that the bead ring fits into 钢圈配合:侧板上,和钢圈配合的平面及锥面 Bottom Container Plate The plate that the bottom sidewall plate is bolted to 模壳底座 Bottom Container Plate Lifting Lug A lug attached to the Bottom Container Plate with Horizontal holes used for lifting. 模壳底座吊耳:装配在底座上、有水平的孔,用来吊装的吊耳 Bottom Container Plate Dowel Pin Lug A lug attached to the Bottom Container Plate that supports the Dowel Pin Bushing. 装配在底座上,用来支承定位销套的突缘 Bottom Container Plate Hold Down A lug that is used to fix the Bottom Plate in the Press. 用来将底座装配在硫化机上的突缘 Breaker Hook A hook fixed to the bottom of the tread segment that catches the bottom container plate only when the segment will not release from the tire during de-molding. 分离钩:固定在花纹块底部的钩子,轮胎硫化完后若花纹块不能跟轮胎分离,就用此钩抓住模壳底座帮助花纹块和轮胎进行分离。
模具--中英文对照
dowel pin 定位梢 draft 拔模锥度 draw bead 张力调整杆 drive bearing 传动轴承 ejection pad 顶出衬垫 ejector 脱模器 ejector guide pin 顶出导梢 ejector leader busher 顶出导梢衬套ejector pad 顶出垫 ejector pin 顶出梢 ejector plate 顶出板 ejector rod 顶出杆 ejector sleeve 顶出衬套 ejector valve 顶出阀 eye bolt 环首螺栓 filling core 椿入蕊 film gate 薄膜形浇口 finger pin 指形梢 finish machined plate 角形模板 finish machined round plate 圆形模板fixed bolster plate 固定侧模板flanged pin 带凸缘销 flash gate 毛边形浇口 flask 上箱 floating punch 浮动冲头 gate 浇口 gate land 浇口面 gib 凹形拉紧楔 goose neck 鹅颈管
guide bushing 引导衬套 guide pin 导梢 guide post 引导柱 guide plate 导板 guide rail 导轨 head punch 顶头冲孔 headless punch 直柄冲头 heavily tapered solid 整体模蕊盒hose nippler 管接头 impact damper 缓冲器 injection ram 压射柱塞 inlay busher 嵌入衬套 inner plunger 内柱塞 inner punch 内冲头 insert 嵌件 insert pin 嵌件梢 king pin 转向梢 king pin bush 主梢 一、入水:gate 进入位:gate location 水口形式:gate type 大水口:edge gate 细水口: pin-point gate 水口大小:gate size 转水口:switching runner/gate 唧嘴口径:sprue diameter 二、流道: runner 热流道:hot runner, hot manifold 热嘴冷流道: hot sprue/cold runner
常用模具零件中英文对照表
常用模具零件中英文对照表 2005-12-19 14:51:17???中国注塑网 入水:gate 进入位:gate location 水口形式:gate type 大水口:edge gate 细水口: pin-point gate 水口大小:gate size 转水口:switching runner/gate 唧嘴口径:sprue diameter 二、流道: runner 热流道:hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形流道:round(full/half runner 流道电脑分析:mold flow analysis :?[??n?l?s?s] 流道平衡:runner balance 热嘴:hot sprue 热流道板:hot manifold 发热管:cartridge heater 探针: thermocouples 插头:connector plug 插座: connector socket 密封/封料: seal 三、运水:water line 喉塞:line lpug 喉管:tube 塑胶管:plastic tube 快速接头:jiffy quick connector plug/socker 四、模具零件:mold components 三板模:3-plate mold 二板模:2-plate mold 边钉/导边:leader pin/guide pin 边司/导套:bushing/guide bushing 中托司:shoulder guide bushing 中托边:guide pin 顶针板:ejector retainer plate 托板:support plate
模具中英文对照表
landed plunger mold 有肩柱塞式模具burnishing die 挤光模 landed positive mold 有肩全压式模具button die 镶入式圆形凹模 loading shoe mold 料套式模具 center-gated mold 中心浇口式模具loose detail mold 活零件模具 chill mold 冷硬用铸模 loose mold 活动式模具 clod hobbing 冷挤压制模 louvering die 百叶窗冲切模composite dies 复合模具 manifold die 分歧管模具 counter punch 反凸模 modular mold 组合式模具 double stack mold 双层模具 multi-cavity mold 多模穴模具electroformed mold 电铸成形模 multi-gate mold 复式浇口模具expander die 扩径模 offswt bending die 双折冷弯模具extrusion die 挤出模
palletizing die 叠层模 family mold 反套制品模具 plaster mold 石膏模 blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具 fantail die 扇尾形模具 pressure die 压紧模 fishtail die 鱼尾形模具 profile die 轮廓模 flash mold 溢料式模具progressive die 顺序模 gypsum mold 石膏铸模 protable mold 手提式模具 hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模 punching die 落料模 lancing die 切口模 raising(embossing) 压花起伏成形re-entrant mold 倒角式模具
模具方面的中英文对照
查看文章模具方面的中英文对照【二】2007-05-09 22:35 塑料成型模具的主要设计要素脱模距stripper distance 脱模斜度draft 投影面积projected area 最大开距maximum daylight;open daylight 闭合高度mould-shut height 抽芯距core-pulling distance 抽芯力core-pulling force 脱模力ejector force 开模力mould opening force 模内压力internal mould pressure;cavity pressure 成型压力moulding pressure 背压环back-up ring 1 bar = 14.5psi 高压接头bite type fitting 液压马达hydraulic motor 冷却水流量计waterflow regulator 打磨器材abrasive material 打磨砂轮grinding wheels 切割砂轮cutting wheels 码模夹(注塑机使用) mould clamps; lifting clamps 小五金工具piping tools 高压力软管high pressure hose 风管,水软管air .water hose 高压油表pressure gauge 压力油喉hydraulic hoses 光塑检测photoelastic testing 吹塑模plastic blow mould 注塑模plastic injection mould 冲扎复合模blank & form compound die 精密冲模precision blanking die 熔料流动率MFR=melt flow rate 熔料流动指数MET=melt flow index 推板导柱guide pin for ejector plater 座板clamping plate 垫块space block(plate) 推板ejector block(plate) afdek plate 档尘板guide stripe 行位后板cavity sub-insert 前模镶件core sub-insert 后模镶件sprue puller insert 扣针镶件 stage ejector 顶棍
模具常用术语中英文对照表
"R,L Co.,Ltd" 模具常用术语中英文对照 模芯Parting Core 局部视图Partial View 冷料# Cold Slag 线切割 Wire 轮廊Contour 螺纹孔 Tapping Hole 连接件 Fittings 斜针Angle Pin 接合Engage 替换镶件Interchangeable Mold Inserts 指定吨位的注塑机Specific Press 水嘴接头Water Fittings 螺纹Eyebolt Thread 回针Stop Pin 二级顶出针Sub-Leaderd Pin 镶件Mold Insert 加硬Harden 唧嘴Sprue 设计筒图Design Preliminary 名称块表Title Block 版本标识Revision Level 材料清单Stock List 制模Build Mold 手动滑块Hand Slide 漏水测试Leak Test 流道排气Runner Vents 抛光Draw Polish 侧抽芯 Side Action 加强筋 Reinforcing
三角撑 Gusset 柱子Bossed 出模斜度Draft 外廊Contour 落单会议Kick-Off Meeting 装卸孔 Handling Hole 运输安全带Moldstrap 码模槽 Clamp Slot 撑头Support Pillar 螺牙1/2-13 Eye Bolt 1/2-13Tap 导柱位 Leader Pin Location 耐落胶 Teflon Paste 偏移量 Offset 水塞Water Line Plug 撬模脚 Ppy Slot 重新加工Reworked 配件Components 补偿Compensation 平面度 Parallel 倒角Chamfer 模胚Mold Base 热嘴Hotnozzle 火花机 Edm 熔接线 Weildline 压机Press 晒纹Texturing 梯形Trapezoid 凸缘、法兰Flange 方铁Spacer Block 顶针板Ejector Plate 顶针底板Ejector Retainer Plate 垫板Retainer Plate
各式模具分类用语中英文对照
Landed plunger mold有肩柱塞式模具Burnishing die 挤光模 Landed positive mold 有肩全压式模具Button die镶入式圆形凹模 Loading shoe mold料套式模具Center-gated mold中心浇口式模具Loose detail mold 活零件模具 Chill mold 冷硬铸模 Loose mold 活动式模具 Cold hobbing冷挤压制模 Louvering die百叶窗冲切模Composite dies 复合模具 Manifold die分歧管模具 Counter punch反凸模 Modular mold 组合式模具 Double stack mold 双层模具 Multi-cavity mold多模穴模具Electroformed mold电铸成形模 Multi-gate mold复式浇口模具Expander die 扩径模 Offswt bending die双折冷弯模具Extrusion die 挤出模 Palletizing die 叠层模 Family mold反套制品模具 Plaster mold 石膏模 Blank through dies漏件式落料模Porous mold 通气性模具Duplicated cavity plate复板模Positive mold全压式模具 Fantail die扇尾形模具 Pressure die压紧模 Fishtail die鱼尾形模具 Profile die轮廓模 Flash mold 溢料式模具Progressive die顺序模 Gypsum mold 石膏铸模 Protable mold 手提式磨具 Hot-runner mold热流道模具Prototype mold 雏形试验模具 Ingot mold钢锭模 Punching die 落料模 Lancing die 切口模 Raising (embossing) 压花起伏成形Re-entrant mold 倒角式模具
模具方面的中英文对照
查看文章模具方面的中英文对照【二】 2007-05-09 22:35 塑料成型模具的主要设计要素脱模距stripper distance 脱模斜度draft 投影面积projected area 最大开距maximum daylight;open daylight 闭合高度mould-shut height 抽芯距core-pulling distance 抽芯力core-pulling force 脱模力ejector force 开模力mould opening force 模内压力internal mould pressure;cavity pressure 成型压力moulding pressure 背压环back-up ring 1 bar = 14.5psi 高压接头bite type fitting 液压马达hydraulic motor 冷却水流量计waterflow regulator 打磨器材abrasive material 打磨砂轮grinding wheels 切割砂轮cutting wheels 码模夹(注塑机使用) mould clamps; lifting clamps 小五金工具piping tools 高压力软管high pressure hose 风管,水软管air .water hose 高压油表pressure gauge 压力油喉hydraulic hoses 光塑检测photoelastic testing 吹塑模plastic blow mould 注塑模plastic injection mould 冲扎复合模blank & form compound die 精密冲模precision blanking die 熔料流动率MFR=melt flow rate 熔料流动指数MET=melt flow index 推板导柱guide pin for ejector plater 座板clamping plate 垫块space block(plate) 推板ejector block(plate) afdek plate 档尘板guide stripe 行位后板cavity sub-insert 前模镶件core sub-insert 后模镶件sprue puller insert 扣针镶件 stage ejector 顶棍 spacer rock(risers) 间隔板变形distortion 弯曲
模具DFM常用中英文对照
DFM常用中英文对照 15、如果分型面此处,模具上会有尖角和刀口,对模具寿命有影响。 There are sharp edges if we set the parting line here, it will reduce the tool life. 16、此处料厚段差很大,成品表面会有应力痕,建议修改如图示。 The thickness is not equal and it will bring the stress lines on the surface, suggest to improve the part as the picture shown. 17、此大行位上有小行位,开模时小行位需先退,大行位做延时,合模时则相反。 The small slider is inside the big slider, when the mold open, the small slider need to recede first and the big slider have to postpone. When the mold close, it is contrary. 18、此处需做强顶。 This position need to force ejection. 19、由于此处没有足够空间下热咀,所以需做一个柱子进胶。 This position need to make a pole for gating because there have no enough space for hot sprue. 20、沾模, Stick 1.High shrinkage values could indicate sink marks or voids at gate location 高缩水率的产品容易产生缩印,但 在浇口附近可以避免。 2.Welding line on the cosmetic surface 熔接线在外表面 3.Two banana gate was to being confluent in the end of melt flow. 两个香蕉浇口在流动未端熔合。 4.Venting insert here has flash 排气镶件处有飞边 5.Venting gap between inserts is too big 镶件处的排气槽过大 6.Stress mark on the cosmetic surface 产品外表面上有压痕 7.Uneven thickness 不平均的产品壁厚 8.Unreasonable product structure 不合理的产品结构 9.Injection speed is high 注塑压力过高 10.There is black spot on the cosmetic surface 产品外表面上有黑色点 11.There is flash on the product 产品有飞边 12.there is sink mark on the cosmetic surface 产品外表面上有缩痕 13.Gate size is not reasonably 浇口尺寸不合理 14.There is argent spot 这里有亮点(银色斑点) 15.The plastic of first shot didn't meet high temperature. 塑料的第一胶不会有很高的温度。 16.Make sure the core float plate was closed before lifter completely return to correct position 确认 lifter完全回位时core侧浮动板已经复位 17.Make sure the ejector system is smooth 确认顶针系统移动平稳 18.Add early return structure to protect lifter return to correct position 增加先复位机构保护lifter回到正确 位置。 19.Propose to add draft on slider side wall and draw polish. 建议增加 slider的角度和抛光角度。 20.It is too thin and very difficult to inject fully, and weakness wall will have risk of the part function 该 处壁厚过薄而造成很难去填充完整,薄壁将会有产品功能上的风险。 21.These are will have sink marks due to uneven thickness, propose to reduce plastic. 壁厚不均匀容易产生缩印, 建议在该处减胶。 22.These are will have sink marks due to ribs opposite. 正面的筋位易导致背面产生缩印。 23.Please confirm the 3D part thickness whether has including painting thickness or not? 请确认产品的设计是否
模具英文缩写对照
模芯 Parting Core 局部视图 Partial View 冷料# Cold Slag 线切割 Wire E.D.M 轮廊 Contour 螺纹孔 Tapping Hole 连接件 Fittings 斜针 Angle Pin 接合 Engage 替换镶件 Interchangeable Mold Inserts 指定吨位的注塑机 Specific Press 水嘴接头 Water Fittings 螺纹 Eyebolt Thread 回针 Stop Pin 二级顶出针 Sub-Leaderd Pin 镶件 Mold Insert 加硬 Harden Sprue唧嘴 Design Preliminary 设计筒图Title Block名称块表 Revision Level版本标识 Stock List 材料清单Build Mold制模 Hand Slide手动滑块 Leak Test 漏水测试Runner Vents 流道排气Draw Polish抛光Side Action侧抽芯 Reinforcing加强筋 Gusset三角撑 Bossed柱子 Draft出模斜度 Contour外廊 Kick-Off Meeting落单会议 Handling Hole装卸孔 运输安全带 Moldstrap 码模槽 Clamp Slot 撑头 Support Pillar 螺牙 1/2-13 Eye Bolt 1/2-13Tap 导柱位 Leader Pin Location 耐落胶 Teflon Paste 偏移量 Offset Water Line Plug水塞Ppy Slot 撬模脚 重新加工 Reworked 配件 Components 补偿 Compensation 平面度 Parallel 倒角 Chamfer
模具常用中英文对照
模具常用术语中英文对照 模芯Parting Core 局部视图Partial View 冷料# Cold Slag 线切割 Wire E.D.M 轮廊Contour 螺纹孔 Tapping Hole 连接件 Fittings 斜针Angle Pin 接合Engage 替换镶件Interchangeable Mold Inserts 指定吨位的注塑机Specific Press 水嘴接头Water Fittings 螺纹Eyebolt Thread 回针Stop Pin 二级顶出针 Sub-Leaderd Pin 镶件Mold Insert 加硬Harden 唧嘴Sprue 设计筒图Design Preliminary 名称块表Title Block 版本标识Revision Level
材料清单Stock List 制模Build Mold 手动滑块Hand Slide 漏水测试Leak Test 流道排气Runner V ents 抛光Draw Polish 侧抽芯 Side Action 加强筋 Reinforcing 三角撑 Gusset 柱子Bossed 出模斜度Draft 外廊Contour 落单会议Kick-Off Meeting 装卸孔 Handling Hole 运输安全带 Moldstrap 码模槽 Clamp Slot 撑头Support Pillar 螺牙1/2-13 Eye Bolt 1/2-13Tap 导柱位 Leader Pin Location 耐落胶 Teflon Paste 偏移量 Offset 水塞Water Line Plug
模具设计与制造中英文外文翻译文献
中英文对照资料外文翻译文献 模具设计与制造 模具是制造业的重要工艺基础,在我国,模具制造属于专用设备制造业。中 国虽然很早就开始制造模具和使用模具,但长期未形成产业。直到20世纪80 年代后期,中国模具工业才驶入发展的快车道。近年,不仅国有模具企业有了很 大发展,三资企业、乡镇(个体)模具企业的发展也相当迅速。 虽然中国模具工业发展迅速,但与需求相比,显然供不应求,其主要缺口集 中于精密、大型、复杂、长寿命模具领域。由于在模具精度、寿命、制造周期及 生产能力等方面,中国与国际平均水平和发达国家仍有较大差距,因此,每年需 要大量进口模具。 中国模具产业除了要继续提高生产能力,今后更要着重于行业内部结构的调 整和技术发展水平的提高。结构调整方面,主要是企业结构向专业化调整,产品 结构向着中高档模具发展,向进出口结构的改进,中高档汽车覆盖件模具成形分 析及结构改进、多功能复合模具和复合加工及激光技术在模具设计制造上的应用、高速切削、超精加工及抛光技术、信息化方向发展。 近年,模具行业结构调整和体制改革步伐加大,主要表现在,大型、精密、复杂、长寿命、中高档模具及模具标准件发展速度高于一般模具产品;塑料模和 压铸模比例增大;专业模具厂数量及其生产能力增加;“三资”及私营企业发展 迅速;股份制改造步伐加快等。从地区分布来看,以珠江三角洲和长江三角洲为 中心的东南沿海地区发展快于中西部地区,南方的发展快于北方。目前发展最快、
模具生产最为集中的省份是广东和浙江,江苏、上海、安徽和山东等地近几年也有较大发展。 虽然我国模具总量目前已达到相当规模,模具水平也有很大提高,但设计制造水平总体上落后于德、美、日、法、意等工业发达国家许多。当前存在的问题和差距主要表现在以下几方面: (1)总量供不应求 国内模具自配率只有70%左右。其中低档模具供过于求,中高档模具自配率只有50%左右。 (2)企业组织结构、产品结构、技术结构和进出口结构均不合理 我国模具生产厂中多数是自产自配的工模具车间(分厂),自产自配比例高达60%左右,而国外模具超过70%属商品模具。专业模具厂大多是“大而全”、“小而全”的组织形式,而国外大多是“小而专”、“小而精”。国内大型、精密、复杂、长寿命的模具占总量比例不足30%,而国外在50%以上。2004年,模具进出口之比为3.7:1,进出口相抵后的净进口额达13.2亿美元,为世界模具净进口量最大的国家。 (3)模具产品水平大大低于国际水平,生产周期却高于国际水平 产品水平低主要表现在模具的精度、型腔表面粗糙度、寿命及结构等方面。 (4)开发能力较差,经济效益欠佳 我国模具企业技术人员比例低,水平较低,且不重视产品开发,在市场中经常处于被动地位。我国每个模具职工平均年创造产值约合1万美元,国外模具工业发达国家大多是15~20万美元,有的高达25~30万美元,与之相对的是我国相当一部分模具企业还沿用过去作坊式管理,真正实现现代化企业管理的企业较少。 造成上述差距的原因很多,除了历史上模具作为产品长期未得到应有的重视,以及多数国有企业机制不能适应市场经济之外,还有下列几个原因:(1)国家对模具工业的政策支持力度还不够 虽然国家已经明确颁布了模具行业的产业政策,但配套政策少,执行力度弱。目前享受模具产品增值税的企业全国只有185家,大多数企业仍旧税负过重。模
模具DFM常用中英文对照
DFM常用中英文对照 欧阳学文 15、如果分型面此处,模具上会有尖角和刀口,对模具寿命有影响。 There are sharp edges if we set the parting line here, it will reduce the tool life. 16、此处料厚段差很大,成品表面会有应力痕,建议修改如图示。 The thickness is not equal and it will bring the stress lines on the surface, suggest to improve the part as the picture shown. 17、此大行位上有小行位,开模时小行位需先退,大行位做延时,合模时则相反。 The small slider is inside the big slider, when the mold open, the small slider need to recede first and the big slider have to postpone. When the mold close, it is contrary. 18、此处需做强顶。 This position need to force ejection. 19、由于此处没有足够空间下热咀,所以需做一个柱子进
胶。 This position need to make a pole for gating because there have no enough space for hot sprue. 20、沾模, Stick 1.High shrinkage values could indicate sink marks or voids at gate location 高缩水率的产品容易产生缩印,但在浇口附近可 以避免。 2.Welding line on the cosmetic surface 熔接线在外表面 3.Two banana gate was to being confluent in the end of melt flow. 两个香蕉浇口在流动未端熔合。 4.Venting insert here has flash 排气镶件处有飞边 5.Venting gap between inserts is too big 镶件处的排气槽过大 6.Stress mark on the cosmetic surface 产品外表面上有压痕 7.Uneven thickness 不平均的产品壁厚 8.Unreasonable product structure 不合理的产品结构 9.Injection speed is high 注塑压力过高 10.There is black spot on the cosmetic surface 产品外表面上有
模具常用术语中英文对照表
模具常用术语中英文对 照表 Document serial number【LGGKGB-LGG98YT-LGGT8CB-LGUT-
"R,L Co.,Ltd" 模具常用术语中英文对照 模芯Parting Core 局部视图Partial View 冷料# Cold Slag 线切割Wire 轮廊Contour 螺纹孔Tapping Hole 连接件Fittings 斜针Angle Pin 接合Engage 替换镶件Interchangeable Mold Inserts 指定吨位的注塑机Specific Press 水嘴接头Water Fittings 螺纹Eyebolt Thread 回针Stop Pin 二级顶出针Sub-Leaderd Pin 镶件Mold Insert 加硬Harden 唧嘴Sprue 设计筒图Design Preliminary 名称块表Title Block 版本标识Revision Level 材料清单Stock List 制模Build Mold 手动滑块Hand Slide 漏水测试Leak Test 流道排气Runner Vents 抛光Draw Polish 侧抽芯Side Action 加强筋Reinforcing
三角撑Gusset 柱子Bossed 出模斜度Draft 外廊Contour 落单会议Kick-Off Meeting 装卸孔Handling Hole 运输安全带Moldstrap 码模槽Clamp Slot 撑头Support Pillar 螺牙1/2-13 Eye Bolt 1/2-13Tap 导柱位Leader Pin Location 耐落胶Teflon Paste 偏移量Offset 水塞Water Line Plug 撬模脚Ppy Slot 重新加工Reworked 配件Components 补偿Compensation 平面度Parallel 倒角Chamfer 模胚Mold Base 热嘴Hotnozzle 火花机Edm 熔接线Weildline 压机Press 晒纹Texturing 梯形Trapezoid 凸缘、法兰Flange 方铁Spacer Block 顶针板Ejector Plate 顶针底板Ejector Retainer Plate 垫板Retainer Plate
模具常用术语中英文对照
模具常用术语中英文对照 模具常用术语中英文对照 中文英文 模芯Parting Core 局部视图Partial View 冷料# ColdSllig 线切割Wire E.D.M 轮廊Contour 螺纹孔Tapping Hole 连接件Fittings 斜针AnglePin 接合Engage 替换镶件Interchangeable Mold Inserts 指定吨位的注塑机SpecificPress 水嘴接头Water Fittings 螺纹Eyebolt Thread 回针Stop Pin 二级顶出针Sub-LeaderdPin 镶件Mold Insert 加硬Hapden 唧嘴Sprue 设计筒图DesignPreliminary 名称块表 Title Block 版本标识Revision Level 材料清单Stock List 制模Build Mold 手动滑块Hand Slide 漏水测试LeakTest 流道排气Runner Vents 抛光Draw Polish 侧抽芯SideAction 中文英文加强筋Reinforcing 三角撑Gusset 柱子Bosse 出模斜度Draft 外廊Contour 落单会议Kick-Off Meeting 装卸孔Handl Ing Hole 运输安全带Moldstrap 码
模槽ClampSlot
撑头Support Pillar 螺牙1/2-13 EyeBolt 1/2-13Tap 导柱位LeaderPin Location 耐落胶Teflon Paste 偏移量Offset 水塞 Water Line Plig 撬模脚PpySlot 重新加工Reworked 配件Components 补偿 Compensation 平面度 Parallel 倒角 Chamfer 模胚 Mold Base 热嘴 Hotnozzle 火花机 Edm 熔接线 Weildline 压机 Press 晒纹 Texturing 梯形Trapezoio 凸缘、法兰Flange 模具常用术语中英文对照 中文英文 方铁 SpacerBlock 顶针板 Ejector Plate
模具中英文对照
冲压模具术语中英文对照文件版本 1.0 制修订日期2008-01-4 制定单位工程部页次 / 页数Page 1 of 10制定人张奎审批 1.目的:为统一本厂冲压模具专业术语的中英文对照作业而制订本文件。 2.范围:适用于本公司各部门之作业。 3.职责:各部人员根据本节内容来进行相关作业。 4.内容: 4.1.1 模具相关术语对照表:spotting['spɑt??] 合模 种类中文名称英文名称中文名称英文名称 模具种类 连续模Progressive die 冲孔模Pierce die 机械手Transfer die 剪边模Trimming die 手动机械手Hand transfer die 下料模Blanking die 单工程模Single die 成形模Forming die 铸造结构模Cast die 折弯模Bending die 简易模Prototype die 围边模Flange die 铆合模Riveting die 拉伸模Draw die 复合模Compound die 快换模Changeable die 工序类 料带strip 料带图strip layout 工序process 冲导正孔pilot pierce 冲孔pierce 侧冲cam pierce 切边notch 切侧刃notch french 折弯bend 墩薄coin 成形form 侧成形cam form 整形restrike 围边flange 打凸米boss / dimple 打凸包emboss 打字印stamp 打沙拉孔hourglass 面押coin burr 抽孔extrude hole 拍平flat 卷圆curl
五金模具常用专业术语中英文对照表
五金模具常用专业术语中英文对照表上模座upperdieset成型公formpunch 脱料板stripper垫板subplate/backupplate 下模座dieplate滑块CAMslider 垫脚parallel误检misfeeder 托板mountingplate顶料销kickoff 初始管位firststartpin带肩螺丝shoulderscrew 两用销lifterpin氮气汽缸gasspring 弹簧护套springcage拔牙螺丝jackscrew 侧冲组件camsection导正装置guideequipment 漏废料孔slughole刀口trimline 加强装置enhanceequipment入子insert 护套bushing整形公restrikeformingpunch 止挡板stopplate挂台head 扣位pocketofhead导柱guidepost 导套guidebushing油嘴oilnipple 接刀口mismatch/cookiebites限位块stopblock 挡块stopper浮块lifter 压块keeper靠块heel 对正块alignmentblock简易模prototypetooling 检具gage/checkingfixture料带图striplayout
闭合高度shuthight俯视图topview 料带strip公差tolerance 正视图frontview走位travel 避位/空pocket退磁demagnetization 间隙clearance真空热外理vacuumheattreatment 镗孔millhole表面外理surfacecoasting 镀钛TDcoasting沉头countersink 精锣finishmill线割wirecutting 穿丝孔firstwirehole斜度taper 镭射laser-cut上夹板/固定座holder/retainer 下模座lowerdieset成刑母公formingdie 电火花EDM码模槽mountingslot 球锁紧固定座ball-lock导尺rail 球锁紧凸模BALL--LOCK送料板railplate 外购outsourcing倒角chamfer 清角SCRAPCHOPPER销钉dowel 尖角sharp--angle普通弹簧coilspring 展开图EXPENSINgDWG三打螺丝spool 镶件insert毛刺burr 键销key插针pilotpin 顶杆lifterbolt结构图dielayout/design 起吊孔handinghole侧视图cross-sectionview